bmw airhead drive shaft repair

You search Auto repair manual PDF bmw airhead drive shaft repair, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bmw airhead drive shaft repair Direct Download speed 5282 Kb/s

  bmw airhead drive shaft repair Full Version speed 6162 Kb/s



BMW Airhead Side Braces Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
Figure B shows the upper end of the Airhead Side Brace where it attaches to the frame ( NOTE: Leave at least 1/2″ spacing below the bottom edge of the fuel tank ). Figure C shows how the Airhead Side Brace must clear the air inlet tubing Figure D showing how the lower edge (beveled end) fits the frame at the rear of the bike. Figure E shows one of the threaded cones properly welded to the frame, and painted. . Ensure Airhead Side Braces are fully assembled (threaded cones firmly bolted into the braces at both ends). 2. Hold Airhead Side Brace in their proper position (reference Figures A-D) to mark location where front and rear threaded cones will be welded to the frame. NOTE : The lower (rear) end of the Airhead Side Brace is beveled, for reference. NOTE : Make sure that both the left and right Airhead Side Braces are positioned equally. 3. Mark the frame and remove paint in the appropriate areas using emery cloth to prepare the frame surface for welding. NOTE : Measure and mark twice, weld once! 4. Hold assembled Airhead Side Braces in their appropriate positions and tack-weld at the top and bottom. Perform this step for both the top (front) and bottom (rear) ends of the Airhead Side Braces , on both sides of the bike. 5. Using removable tape, mark each Airhead Side Brace as either “left” or “right”, to make sure they are replaced onto the appropriate side of the bike after disassembly. 6. Remove the bolts, and the Airhead Side Braces from the tack-welded, threaded cones. Complete the welding of the threaded cone to the motorcycle frame at all 4 locations. 7. Clean/remove any weld splatter, and paint to protect threaded cone and frame from corrosion (see Figure E). 8. Re-assemble Airhead Side Braces onto threaded cones maintaining original left side/right side orientation. NOTE : The lower (rear) end of the Airhead Side Brace is beveled, for reference. 9. Torque hex bolts to 7 ft/lbs

Incoming search terms:

1994 – 2004 BMW Motorcycle History

0

Filed Under (BMW) by admin on 17-11-2010

download
1994 brought many changes to BMW, most obviously by the introduction of the “R259″ series twins and the elimination of the old standby “Airhead” twins that had been BMW’s trademark for seven decades. While it is interesting to look at all the technologies introduced during the 1994 to 2004 time block, it is also exciting to look into what was going on as far as changes in BMW more esoteric than measurable. In this author’s opinion there were unspoken changes in BMW’s mindset and philosophy. BMW had forged it’s reputation for long lasting, simple machines built to the highest standards and quality; aimed at a dwindling, older (OK, Jeff, more mature) market of enthusiastic but eccentric riders. They built motorcycles that were easy for the owners to maintain and modify to fit their specific wants. BMW had always built their bikes their way; often it seemed like they did so in spite of what the younger and upwardly mobile riders were looking for. By 1994, the airhead was simply not a sellable motorcycle; the buying market was younger and wanted performance in line with what the Japanese products offered at much lower prices. The K 75/100 series that were so far ahead of their time in 1984 when they were introduced were also showing their age. No doubt, BMW knew this was coming many years before the new “Oil Head” was introduced. They knew that the riding community had reduced its mean age substantially. The younger riders had money to spend on a bike that had to be BMW, yet had to be totally more modern both in performance and in perception than what BMW had been selling. Thus, the R259 was born. The Birth of the R259 Twins The new BMW corporate mindset, if you will, was no longer concerned with selling motorcycles that would be handed down from one generation to the next, nor was BMW concerned about ease of maintenance with standard hand tools. Although the new bikes were still able to outlast the riders, the concern for building units to last a quarter-million miles was not so much in the forefront of the design. The new models would have to be powerful, fast, handle better than anything on the road; they would need to offer a standard of technology that the Japanese would never build. They should be complex pieces of rolling art. Most obvious, though, was that they would build a product aimed at an entirely new market of riders who would likely not be interested in maintaining the bikes themselves or really understanding the nuances of design. The new customers BMW was looking for were serious riders who were more interested in the fun and excitement of riding than they were in savoring the history of the older designs

Incoming search terms:

MECHANIC CERTIFICATION REQUIREMENTS MDOS Form: Repair Facility Manual

0

Filed Under (Tips and Review) by admin on 18-11-2010

download
Chapter 7: Mechanic Certification Requirements Page 4 7-2.2 Heavy-duty Truck Certification Categories. The Heavy-duty Truck Repair categories requiring mechanic certification to repair vehicles over 10,000 pounds G.V.W. are: a) Engine Repair, Gasoline; b) Engine Repair, Diesel; c) Drive Trains; d) Brakes and Braking Systems; e) Suspension and Steering Systems; f) Electrical Systems; g) Collision-Related Mechanical Repair. 7-2.3 Other On-road Vehicle Certification Categories. Repair categories for other on-road vehicles that require mechanic certification to perform repairs are: a) Motorcycle; b) Recreational Trailer. Automobile and Light Truck Certification Categories. The repair categories requiring mechanic certification to repair vehicles under 10,000 pounds gross vehicle weight (G.V.W.) are: a) Engine Repair; b) Engine Tune-up/Performance; c) Front End, Suspension and Steering Systems; d) Brakes and Braking Systems; e) Automatic Transmission; f) Manual Transmission, Front and Rear Drive Axles; g) Electrical Systems; h) Heating and Air Conditioning; i) Collision-Related Mechanical Repair; j) Unitized Body Structural Repair; k) Pre-1973 Vehicle Repair

Incoming search terms:

KTM 3V TURBO DRIVE MODEL 9808T KNEE FEED Installation and Removal Manual

0

Filed Under (KTM) by admin on 28-01-2012

download
Gather together the following items that you will need to complete this installation. a) lathe b) 3/8″ electric hand drill c) 9/32″ diameter transfer punch SERVO Turbo Drive Model 9808T Page 2 d) .4375 drill, 3/16″ drill, #7 drill e) 1/4-20 tap f) 3/4″ socket wrench g) set of inch hex wrenches h) clean shop rag Step 2: Clean the power feed mounting area completely. Step 3: Remove the drive clutch nut and the drive clutch from the elevating jack shaft. Step 4: Remove the dial nut, dial, and dial carrier. Keep the dial for reuse later. Step 5: Remove the existing bearing retainer. Keep the screws for reuse later. Step 6: Pull jack shaft out of knee. Hold inboard end up while removing to avoid damage to the pinion gear. Step 7: Press the bearing off the jack shaft. Step 8: Drill and ream the end of the jack shaft .4375″ diameter by 13/16″ deep. The .4375″ dia. must be concentric to the shaft O.D. within .002″ T.I.R. Chamfer 1/32″ x 1/2″ diameter. For best results, machining should be done in a lathe. Step 9: Place the shaft extension #6975 into the end of the jack shaft. Finish drill 3/16″ diameter through the shaft and pin the extension with the 3/16″ diameter x 5/8″ long roll pin. File smooth. Step 10: Reassemble and replace the jack shaft in the machine. Step 11: Replace the existing bearing retainer with #57904 retainer provided. Secure using existing screws. Step 12: Slip spacer #5426 and bearing race #1616 onto the jack shaft. Slide the adaptor #0771 over the bearing race and locate against front of the knee.

Incoming search terms:

BMW R 1200 C And R 850 C REPAIR MANUAL

0

Filed Under (BMW) by admin on 22-11-2010

download
BMW Inspection 1000 km/600 miles I -BMW Service II -BMW Inspection III -BMW Annual Service IV Reading out MoDiTeC fault memory (Inspections I, II, III and IV) • Remove the left air cleaner trim panel. • Connect MoDiTeC to diagnostic plug. • Read out the fault memory. • Perform any repair work indicated. Checking throttle cable play, adjusting if necessary (Inspections I and III) • Check throttle cable for free movement and freedom from abrasion or kinking; renew if neces- sary. • With the steering turned to various angles, open the throttle twistgrip fully and allow it to close again. • When released, the twistgrip must return to the closed position by itself. • Pull back the protective cap. • Preset throttle cable play with the engine cold to 1.5 mm (0.06 in). • Warm the engine up to its regular operating tem- perature. • Adjust throttle cable play to 0.5mm (0.02 in) Changing engine oil, renew oil filter element (Inspections I, II, III and IV) L Note: If the motorcycle is ridden only for short distances or outside temperatures are below 0°C (32°F): change the oil and renew the oil filter element every 3 months, but at least every 3 000 km (1 800 miles). • Change the oil while it is at regular operating temperature. • Remove screw plug. • Unscrew oil drain plug and drain off oil. • Fit new seal and screw in drain plug. • Use oil filter wrench, BMW No. 11 4 650 , to unscrew and remove the oil filter. • Coat sealing ring on new oil filter element with oil and screw in. • Add oil. • Insert and tighten the screw plug. • Check engine oil level with the motorcycle in a horizontal position; use the auxiliary stand, BMW No. 001550 . e Caution: Never add engine oil above the MAX mark. X Tightening torque: Oil filter………………………………………………… 11 Nm Oil drain plug………………………………………… 32 Nm Fill quantity for engine: With oil filter change.. 3.75 l (6.6 Imp. pints/3.96 US quarts) Without oil filter change.. 3.50 l (6.2 Imp. pints/3.69 US quarts) Oil volume between MIN and MAX marks……0.50 l (0.88 Imp. pint/0.52 US quart) Engine oil grade: Brand-name HD oil for four-stroke spark-ignition engine, API classifications SE, SF, SG; combination with CC or CD specification

Incoming search terms:

BMW F650 CS Front belt wheel not correctly secured

0

Filed Under (BMW) by admin on 23-11-2010

download
2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure 2.3 Wear check gearbox main shaft- It is extremely important that the techni- cian always check that the dimensions of the gearbox main shaft splines are to specification before proceeding with the installation of a new front belt wheel. This note only applies to motorcycles with accumulated mileage, not to new motorcycles from the crate. If the visual inspection was satisfactory and the main shaft was not replaced for visual damage, a main shaft wear check will be necessary. This check requires the use of BMW Special Tool # 23 4 571 . The adapters are designed for micrometer gauges with stud diameters from 6.35 mm to 6.6 mm. Do not use cellulose-lacquer thinners to clean the adapters as there is a risk of damaging the measuring instruments. Make sure that the micrometer gauges and the adapters are perfectly clean

Electronic Speedo Drive for Toyota T50 5 Speed Transmission

0

Filed Under (Toyota Manuals) by admin on 20-09-2011

Download
Disassembly is simple, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” ring from the housing. Wash all parts internally and externally to remove oil, grease and road grime This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” rings from the housing. Remove the three (3) philips head screws from the cover on the top of the drive housing. Carefully remove cover, be aware that the small parts in side may be stuck to the cover. Remove all internal parts, record order of assembly. Wash housing and shaft to remove oil, grease and road grime. The T50 drive shaft needs to be shortened to a similar length to the AE101. I reassembled the AE101 shaft and housing, and then measured from the top face of the AE101 housing down to the top of the AE101 drive shaft. ( Fig.4) Record this reference depth, (I got 17mm)

Incoming search terms:

Integral ABS and ASC – new Riding Dynamic Control Systems for BMW Motorcycles

0

Filed Under (BMW) by admin on 16-11-2010

download
Entering its next generation, BMW Motorrad Integral ABS is taking a quantum leap in the process of evolution, advancing from a stand-alone solution acting only on the brakes into a fully networked all-round system. Offering the new generation of Integral ABS, BMW Motorrad provides the foundation for additional dynamic riding control systems with a reduction in technical requirements and features. And following the customer’s wishes, this new generation also opens up the option in future for further-reaching rider assistance functions. The first step in this direction is BMW Motorrad ASC Automatic Stability Control available as of 2007. This system serving to control drive spin on a production motorcycles is being introduced as an optional extra on the touring models in the BMW K and Boxer Series. Once again, therefore, BMW is acting as the pioneer in the introduction of advanced safety technologies on the motorcycle. This further enhances the leadership which BMW Motorrad has shown in the area of active safety for more than 15 years. Choosing the right development partner for both systems, BMW Motorrad obviously had to focus on that partner’s specific competence in control technology and the networking of functions within the vehicle. In recent years, major car suppliers have become aware of the technical challenges presented by the motorcycle with its specific riding dynamics and the growing potential for motorcycle control systems in the market. The decisive point in preselection of the development partner was the willingness and ability to develop specialised solutions suitable for use on BMW motorcycles. So taking this into account, joint development of the new generation of ABS brake technology started together with Continental-Teves in early 2003. Integral ABS. BMW Motorrad’s new Integral ABS technology has been developed separately from the previous system and the entire layout of the system has been newly conceived from the ground up. Capitalising on progress in technology in both hydraulics and electronics, the development engineers have succeeded in simplifying the architecture of the system while at the same time enhancing its functions to an even higher standard. The result is supreme stopping power and very short stopping distances even without electrical power assistance on the brakes.

Incoming search terms:

BMW F 650 CS Rear belt wheel cracks Removal And Installation Manual

0

Filed Under (BMW) by admin on 12-11-2010

download
Relieve the tension of the toothed belt and lift the belt off the belt wheel (refer to F 650CS Repair Manual, 00.57). 2) Remove 6 screws (see arrow in photo at right). 3) Remove the rear belt wheel. 4) Clean and degrease the tapered bores and the threads of the mounting screws 5) Carefully place the new belt wheel in position on the damper, coat the screw threads with Loctite 243 and hand tighten the securing screws. 6) Tighten the securing screws to the specified torque maintaining a diagonally opposite tightening sequence throughout (Torque to 28 NM, curing time 12 hours). 7) Measure the vertical runout of the belt wheel (refer to F 650 CS Repair Manual, 33.15). 8) Install and adjust the rear drive belt (refer to F 650 CS Repair Manual 00.57 – 00.58) 2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure.

Incoming search terms:

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

Incoming search terms: