bmw f800gs air box mod

You search Auto repair manual PDF bmw f800gs air box mod, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bmw f800gs air box mod Direct Download speed 5282 Kb/s

  bmw f800gs air box mod Full Version speed 6162 Kb/s



Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

2009 Kawasaki ULTRA 250X/ 260X FUEL INJECTION CONTROLLERS And REGULATORS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The R&D high performance Air Filter Kit will improve acceleration and top speed performance by increasing air flow and reducing air temperatures that enter directly into the Ultra 250X’s air plenum box area. The O.E.M. air plenum box on the Ultra 250X is a great design that will flow plenty of air. However, the air that feeds the plenum box is heated by the engine. R&D has created an easy to install “flat filter” that installs directly in place of the large center access inspection cover located directly under the main glove box. The R&D Flat Air Filter insert will allow unrestricted fresh and cool air to enter the air plenum box area which will add power you can feel and a nice high performance tone. The R&D Performance Filter Kit also features two filters, one for each of the surge and blowoff protections valves. The O.E.M. surge valve recycles compressed hot air back into the air box plenum at idle and under deceleration conditions. The R&D surge and blowoff valve filter kit removes the air recycling hoses which will keep the hot air from entering the air plenum box reducing the engines intake air temperatures. The R&D Ultra 250X Air Filter Kit offers great performance tips on how to remove the restrictive air vent hoses which will further reduce the under seat ambient air temperatures. The R&D Filter system does not remove or alter the O.E.M. plenum box in any way, therefore there are no questions to be answered regarding water ingestion

Incoming search terms:

Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

Air Shock Installation Instructions

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
Air HoseInstallation. Choose the most convenient loca- tiononyour motorcycle for the air fill valve. Drilla 5/16″hole and install the air fill valve as shown in Figure 3orsecure air fill valve to frame tube. 2. Keep hose ends clean during installation because dirt can cause air leaks. 3. Install hose connector, tube clamp and two O-rings onto one end of the air hose (See Figures4&5) Apply rubber lubricant (soap solution, not oil) to the O-rings to ease installation on the air hose& into the shock absorber inlet. Plastic connector should just bottom on fitting. Do not overtighten! The function of the nut is to hold everything together in place, the O- rings do the sealing. Fin- gertightenonly (10 in/lb maximum). 4. After routing the air hose, trim the length to fit air fill valve. Install hose connector, tube clamp, and twoO-rings onto end of hose (See figures 4&5). Lubricate as above and assemble to air fill valve. Use the same procedure formating hose. Important —leaveasmall amount of slack in hose near shock absorber to allow for the slight move- mentofthe shock. Caution! Do not install hose near ex- haustsystem, battery or any other sharp edges or seat movement. Keep hoses clear of moving parts such as wheels or suspension components. Do not allow hoses to have excess slack and sag below the motorcycle. The hoses could catch on road surfaces or debris and could be damaged while the motorcycle is in motion. 5. If necessary the air hose can be secured along the motorcycle’swiringharness with tie-wraps. 6. Testing: Inflate system to 50 psi. Apply soapy water solution to all connections and check for air leaks. If there are any leaks, disconnect the suspected fitting and check for dirt or damage to the air line or the O-rings. Remove any dirt or foreign matter, re-lubricate the O-rings and reinstall. If unable to locate the leak, remove rubber boot from shocks and submerge pressurized components under water (in- cludingT-Valve) and check for leaks. If you cannot solve the air leak problem, please contact our technical staff for assistance

KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

1994 – 2004 BMW Motorcycle History

0

Filed Under (BMW) by admin on 17-11-2010

download
1994 brought many changes to BMW, most obviously by the introduction of the “R259″ series twins and the elimination of the old standby “Airhead” twins that had been BMW’s trademark for seven decades. While it is interesting to look at all the technologies introduced during the 1994 to 2004 time block, it is also exciting to look into what was going on as far as changes in BMW more esoteric than measurable. In this author’s opinion there were unspoken changes in BMW’s mindset and philosophy. BMW had forged it’s reputation for long lasting, simple machines built to the highest standards and quality; aimed at a dwindling, older (OK, Jeff, more mature) market of enthusiastic but eccentric riders. They built motorcycles that were easy for the owners to maintain and modify to fit their specific wants. BMW had always built their bikes their way; often it seemed like they did so in spite of what the younger and upwardly mobile riders were looking for. By 1994, the airhead was simply not a sellable motorcycle; the buying market was younger and wanted performance in line with what the Japanese products offered at much lower prices. The K 75/100 series that were so far ahead of their time in 1984 when they were introduced were also showing their age. No doubt, BMW knew this was coming many years before the new “Oil Head” was introduced. They knew that the riding community had reduced its mean age substantially. The younger riders had money to spend on a bike that had to be BMW, yet had to be totally more modern both in performance and in perception than what BMW had been selling. Thus, the R259 was born. The Birth of the R259 Twins The new BMW corporate mindset, if you will, was no longer concerned with selling motorcycles that would be handed down from one generation to the next, nor was BMW concerned about ease of maintenance with standard hand tools. Although the new bikes were still able to outlast the riders, the concern for building units to last a quarter-million miles was not so much in the forefront of the design. The new models would have to be powerful, fast, handle better than anything on the road; they would need to offer a standard of technology that the Japanese would never build. They should be complex pieces of rolling art. Most obvious, though, was that they would build a product aimed at an entirely new market of riders who would likely not be interested in maintaining the bikes themselves or really understanding the nuances of design. The new customers BMW was looking for were serious riders who were more interested in the fun and excitement of riding than they were in savoring the history of the older designs

Incoming search terms:

HARLEY DAVIDSON LOCKING GLOVE BOX DOOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. Unsnap the original equipment (O.E.) left-side glove box door, and unfasten the tether by bringing the aglet end (see Figure 1, B) out through the retaining hole. Always wear proper eye protection when drilling or grinding. Flying debris could cause serious eye injury. (00402e) 2. Using an 3/16 inch (5 mm) bit positioned in the center of each snap, drill out the four plastic snaps surrounding the glove box opening. NOTE The glove box door, hinge and frame assemblies are side- specific. The assemblies install so that the tether retaining hole (C) in the door frame is to the inboard side. 3. Obtain the new left-side glove box door, hinge and frame assembly (1), a lock (2) and a tether assembly (8) from the kit. Remove the nut (3) from the lock. 4. Insert the lock through the hole in the glove box door as shown. Assemble the tether over the lock threads with the tab (A) on the inboard side of the lock, same as the retaining hole in the door frame. Tighten securely. 5. Open the left-side door, and position the door assembly at the glove box opening, lining up the holes. 6. Insert a screw (9) through each of the holes in the door frame and glove box. Install a hex nut with washer (10) onto the threads of each screw. Tighten finger-tight. NOTE Ambient temperature should be at least 60° F (16° C) for proper adhesion of the gaskets to the glove box door frame. 7. Clean the glove box door frame with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. NOTE The glove box gaskets are side-specific. With the paper backing facing the door frame, the oblong hole at the top of the gasket is to the outboard side. 8. Obtain the left-side gasket (6) and a hinge gasket (7) from the kit. Install the gaskets to the glove box door frame. a. The gasket liner on the large gasket is split to aid alignment. Peel one half of the liner from the adhesive backing of the left-side gasket. b. Using the frame edges and screw heads as a guide, carefully position the gasket to the glove box door frame and press firmly into place. c. Peel the remaining half of the liner from the gasket backing, and carefully position the rest of the gasket to the door frame. Press firmly into place. d. Apply steady pressure for a few seconds at all areas of the gasket to verify proper adhesion. e. Peel the liner from the hinge gasket. f. Carefully position the gasket to the door frame above the hinge, and press firmly into place.

Incoming search terms:

HARLEY DAVIDSON TOURING SUSPENSION AIR PUMP KIT OPERATION/ INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
OPERATION 1. Remove cap from air suspension air valve and connect pump by threading the air valve adapter (1) on the pump as shown in Figure 1. When adapter is threaded properly, the current air pressure in the system will be indicated on the gauge of the pump. Do not exceed maximum air pressure for rear suspension. Air components fill rapidly. Therefore, use low air line pressure. Failure to do so may result in possible damage to components. (00165a) NOTES See the motorcycle’s Owner’s Manual or, if installed, the air suspension lowering kit’s instruction sheet for the recommended air pressures. Using pressures outside the recommended loading range will result in a reduction of available suspension travel and reduced rider comfort. 2. To increase pressure, operate the air pump handle (4) until the desired pressure is indicated on gauge (2). Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak onto the rear wheel, tire and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) NOTE The pressure release button is designed to release pressure slowly. If the button is completely or rapidly depressed, no air will be released. For the best results, depress the pressure release button slowly and only partially. 3. To decrease pressure, slowly depress the pressure release button (3) on the pump until desired pressure is indicated on gauge (2)

MOUNTAIN BIKE AIR SHOCK SET-UP AND TUNING GUIDE

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
DETAILED SET-UP 2. Installing Air Pressure – Remove the air cap from the Schrader valve on the end of the shock body. Attach the pump to the Schrader valve. Some people damage their pumps by screwing them on too far. As soon as the gauge registers pressure, screw 1/2 turn more and pump to the desired level. Use the release button on the pump to reduce air pressure. The hiss you hear when unscrewing the pump is only the air from the pump and not from the shock! Likewise, when you install the pump again, you will also hear a hiss as air from the shock fills the pump and reduces the registered pressure you previously installed. All perfectly normal when pressurizing the shock! After removing the pump, be sure to reinstall the Schrader valve cap. If the shock does not dampen properly after pressurizing, the air pressure may have been lost during pump removal as a result of a worn pump fitting o-ring that needs replacement. Do not ride the bike until the shock is properly pressurized. 3. Main Air Spring Pressure Adjustments – Air Spring adjustments are made by inflating or deflating the main air spring chamber. Since your IFP air pressure adjustment (outlined above) also affects your starting spring force, you should always adjust your IFP pressure before adjusting the main air spring pressure. You can refer to the online Quick Start guide at: www.progressivesuspension.com/literature.html for accurate main air spring pressure and sag settings matched to your bike model and body

BMW 3 SERIES INSTALLATION MANUAL

0

Filed Under (BMW) by admin on 17-11-2010

download
1. Turn off the ignition and disconnect the negative battery cable. NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft code to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code. TO START: 2. Depress the wire-locking clip and disconnect the mass air sensor electrical. BMW 3 SERIES (E46) 1999-00 323i, ci 1999 323iC 2001-05* 325i, ci L6-2.5L 1999-00 328i 2000 328ci 2002-05 325xi L6-2.8L NOTE: * Excluding 2003 & 2005 PZEV model with engine family 3BMXV02.5M56 & 5BMXV02.5M56 Flat Blade Screwdriver Ratchet Extension 10mm Socket 10mm Wrench 4mm Allen A intake tube (EL) 1 087139 B hose ; 4mm id x 2″ l 1 08062 C npt fi tting; 1/4″ x 5/16″ barb 1 08908 D hose clamp #48 3 08601 E silicone hose 3.25″id x 2″l 1 08690 F nut; 6mm nylock 7 07553 G washer; 1/4″id x 5/8″od fl at 7 08275 H washer; 1/4″ split lock 1 08198 I bolt; 6mm-1.00 x 16mm, b/h/a 2 07730 J bolt; 6mm-1.00 x 12mm, b/h/a 4 07794 K washer; 1/4″id x 1″od fender 2 08160 L bracket 1 010087 M heat shield “A” 1 07492 N heat shield “C” 1 07497 O heat shield “B” 1 07494 P edge trim 46″L 1 102487 Q air fi lter 1 RU-4730 3. Pull up on the four fresh air duct-retaining pins to release them from the radiator core support. 4. Lift up and remove the fresh air duct from the vehicle as shown. NOTE: Disconnect the fresh air tube from the fresh air duct. 5. Loosen the hose clamp which secures the intake tube to the mass air sensor, and then disconnect the intake tube from the mass air sensor as shown. 6. Remove the two-factory air box mounting bolts shown.

Incoming search terms: