bmw r1200rtp luggage conversion

You search Auto repair manual PDF bmw r1200rtp luggage conversion, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bmw r1200rtp luggage conversion Direct Download speed 5282 Kb/s

  bmw r1200rtp luggage conversion Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL DETACHABLE TWO-UP TOUR-PAK LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download

TOUR-PAK LUGGAGE INSTALLATION TO RACK 1. Open the lid and, if necessary, remove all items from inside the Tour-Pak luggage.  Remove the rubber mat from the luggage floor. 2. If holes ARE NOT pre-drilled in the floor of the luggage,       see Figure 1. To prevent damage to the leather while drilling, place blocks of wood underneath the Tour-Pak luggage at the drilling sites.  Use the four inboard holes (3) in the metal base of the luggage (2) as a guide, and carefully drill four 11/32 inch (9 mm)  holes through the floor of the luggage. 1 2 3 is04249 1. Front of motorcycle 2. Tour-Pak 3. Drill four 11/32 inch (9 mm) diameter holes Figure 1.  Drill Attachment Hole Locations in Tour-Pak NOTE See Figure 3. When installing the luggage to the rack in the following steps, note that holes in the luggage rack (2) provide forward (A) and rearward (B) positions for mounting the lug- gage. 3. Place the luggage on the luggage rack.  Align the holes in the luggage mounting plate with the forward or rearward holes in the rack. 4. ALL applications: Obtain the hex head cap screws (9), lock nuts (11) and plain washers (10) from the kit. Place a washer over the threads of each screw, and insert the screw threads, from the inside, through the Tour-Pak luggage mounting plate and floor, and into the holes in the rack. NOTE Always install the mounting screws from inside the luggage.  If the screws are installed from the bottom, the screw ends can tear the rubber mat and scratch objects, such as helmets, stored inside the luggage. 5. From the underside of the rack, install a washer and lock nut onto the threads of each screw.  In a crosswise pattern, incrementally tighten each screw to 19 ft-lbs (25 Nm) . 6. Install the rubber mat into the luggage.  Close and latch the lid. 7. If not already in place, install the Detachable Docking Hardware Kit to the vehicle per the instructions in that kit

1994 – 2004 BMW Motorcycle History

0

Filed Under (BMW) by admin on 17-11-2010

download
1994 brought many changes to BMW, most obviously by the introduction of the “R259″ series twins and the elimination of the old standby “Airhead” twins that had been BMW’s trademark for seven decades. While it is interesting to look at all the technologies introduced during the 1994 to 2004 time block, it is also exciting to look into what was going on as far as changes in BMW more esoteric than measurable. In this author’s opinion there were unspoken changes in BMW’s mindset and philosophy. BMW had forged it’s reputation for long lasting, simple machines built to the highest standards and quality; aimed at a dwindling, older (OK, Jeff, more mature) market of enthusiastic but eccentric riders. They built motorcycles that were easy for the owners to maintain and modify to fit their specific wants. BMW had always built their bikes their way; often it seemed like they did so in spite of what the younger and upwardly mobile riders were looking for. By 1994, the airhead was simply not a sellable motorcycle; the buying market was younger and wanted performance in line with what the Japanese products offered at much lower prices. The K 75/100 series that were so far ahead of their time in 1984 when they were introduced were also showing their age. No doubt, BMW knew this was coming many years before the new “Oil Head” was introduced. They knew that the riding community had reduced its mean age substantially. The younger riders had money to spend on a bike that had to be BMW, yet had to be totally more modern both in performance and in perception than what BMW had been selling. Thus, the R259 was born. The Birth of the R259 Twins The new BMW corporate mindset, if you will, was no longer concerned with selling motorcycles that would be handed down from one generation to the next, nor was BMW concerned about ease of maintenance with standard hand tools. Although the new bikes were still able to outlast the riders, the concern for building units to last a quarter-million miles was not so much in the forefront of the design. The new models would have to be powerful, fast, handle better than anything on the road; they would need to offer a standard of technology that the Japanese would never build. They should be complex pieces of rolling art. Most obvious, though, was that they would build a product aimed at an entirely new market of riders who would likely not be interested in maintaining the bikes themselves or really understanding the nuances of design. The new customers BMW was looking for were serious riders who were more interested in the fun and excitement of riding than they were in savoring the history of the older designs

Incoming search terms:

HARLEY DAVIDSON XR1200 LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
Kit 53976-08 (XR1200 Passenger Upright Kit) is available for separate purchase. Contact your Harley-Davidson dealer for more information. Kit Contents See Figure 2 and Table 1. REMOVAL 1. Remove pillion and seat following the instructions in the appropriate Service Manual. 2. Remove the seat base following the instructions in the appropriate Service Manual. 3. See Figure 1. Remove the turn signal mounting screws (3) and discard. Allow the turn signal to hang by the harness until lower bracket installation. 4. Remove the rear fender support strut screws (6) and dis- card. INSTALLATION 1. See Figure 2. Install lower luggage rack mount bracket with screws (9), flat washers (10) and nuts (8). Bracket will mount around nut (Item 2 in Figure 1). Tighten to 19 ft-lbs (26 Nm) . 2. Install screws (7) and nuts (8) through the rear fender support strut and the lower luggage rack mount bracket. Tighten to 19 ft-lbs (26 Nm) . 3. Route the turn signal wire harnesses through the groove in the bracket. Install new turn signal mounting screws (11). Tighten screws to 3-5 ft-lbs (4-7 Nm) . 4. Install seat base following the instructions in the appropriate Service Manual. 5. Install upper luggage rack mount bracket (4) with original equipment seat base screws in the lower holes (A). Do not tighten at this time. 6. Install screws (3) into slotted holes in the upper luggage rack mount bracket (4) and flange nuts (6). Slide the upper bracket as far back in the slots as possible. Tighten screws (3) to 10 ft-lbs (13.5 Nm) 4 1 1 2 5 6 3 is05250 1. Lower luggage rack mount bracket screw (4) 2. Nut (2) 3. Turn signal mounting screw (4) 4. Upper luggage rack mount bracket 5. Luggage rack 6. Rear fender support strut screw (2) Figure 1. Luggage Rack Installation NOTE If installing the Passenger Upright Kit (part number 53976-08) (available separately), do not install spacers (2) and screws (3) in front holes. 7. Install luggage rack (1) aligning the holes with the holes in the upper luggage rack mount bracket. Install spacers (2) and screws (3) in holes. Tighten to 6-10 ft-lbs (8-13.5 Nm) . After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 8. Install pillion and seat following the instructions in the appropriate Service Manual. Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a

Integral ABS and ASC – new Riding Dynamic Control Systems for BMW Motorcycles

0

Filed Under (BMW) by admin on 16-11-2010

download
Entering its next generation, BMW Motorrad Integral ABS is taking a quantum leap in the process of evolution, advancing from a stand-alone solution acting only on the brakes into a fully networked all-round system. Offering the new generation of Integral ABS, BMW Motorrad provides the foundation for additional dynamic riding control systems with a reduction in technical requirements and features. And following the customer’s wishes, this new generation also opens up the option in future for further-reaching rider assistance functions. The first step in this direction is BMW Motorrad ASC Automatic Stability Control available as of 2007. This system serving to control drive spin on a production motorcycles is being introduced as an optional extra on the touring models in the BMW K and Boxer Series. Once again, therefore, BMW is acting as the pioneer in the introduction of advanced safety technologies on the motorcycle. This further enhances the leadership which BMW Motorrad has shown in the area of active safety for more than 15 years. Choosing the right development partner for both systems, BMW Motorrad obviously had to focus on that partner’s specific competence in control technology and the networking of functions within the vehicle. In recent years, major car suppliers have become aware of the technical challenges presented by the motorcycle with its specific riding dynamics and the growing potential for motorcycle control systems in the market. The decisive point in preselection of the development partner was the willingness and ability to develop specialised solutions suitable for use on BMW motorcycles. So taking this into account, joint development of the new generation of ABS brake technology started together with Continental-Teves in early 2003. Integral ABS. BMW Motorrad’s new Integral ABS technology has been developed separately from the previous system and the entire layout of the system has been newly conceived from the ground up. Capitalising on progress in technology in both hydraulics and electronics, the development engineers have succeeded in simplifying the architecture of the system while at the same time enhancing its functions to an even higher standard. The result is supreme stopping power and very short stopping distances even without electrical power assistance on the brakes.

HARLEY DAVIDSON TOUR-PAK KIT INTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the rubber mat from the bottom of the Tour-Pak. 2. See Figure 1 and Table 1 to determine the proper hole configuration to attach the Tour-Pak to your luggage rack. Holes will be drilled as explained in Step 3 in the hole location for your luggage rack. Table 1. Luggage Rack and Hole Configurations Hole Configura- tion Luggage Rack C (3 holes) Stock 1997 B (4 holes) Detachable luggage rack 53107-96 A (5 holes) Luggage rack 53118-97A and luggage rack 53118-98 A (5 holes) Stock 1998 and later racks A (5 holes) Detachable Tour-Pak rack 53276-04 B (4 holes) Solo detachable Tour-Pak rack 53655-04 B (4 holes) Detachable Tour-Pak rack 53066-00B B (4 holes) Solo detachable Tour-Pak rack 53559-04A A (5 holes) Solo detachable Tour-Pak rack 53260-02 -J03631 1 of 3 B 1 A C 2 2 2 is00163 1. Front of motorcycle 2. Bottom view of Tour-Pak interior (rubber mat removed) Figure 1. Hole configurations for Tour-Pak attachment NOTE Drilling holes in Tour-Pak without wood underneath each hole site may result in the leather becoming damaged during the drilling process. 3. Place blocks of wood underneath the Tour-Pak where the holes will be drilled to prevent damage to the leather while drilling. Use the pre-drilled holes in the metal base as a guide and carefully drill the holes through the leather in the proper location using a 11/32 inch drill bit. 4. See Figure 2. For detachable luggage racks (53107- 96, 53066-00B and 53276-04): Install black cover tube to the front bar (1) of the luggage rack, as shown. This tube is used to provide a cleaner look. The black cover tube is not for use with other luggage racks. 5. Attach Tour-Pak to rack using the mounting screws provided in the Luggage Rack kit. Put bolt through from inside of Tour-Pak. Tighten screws to specifications found in the Luggage Rack kit. 6. Place the black rubber mat on the bottom of the Tour-Pak. 7. If luggage rack was removed, reattach to motorcycle according to kit instructions or Service Manual instructions

BMW Motorcycle F 650 GS/ F 800 GS Accessories

0

Filed Under (BMW) by admin on 20-11-2010

download
Stowage-equipment line Vario case, black, left 71 60 7 696 299 £184 / G Vario case, black, right 71 60 7 696 300 £185 / G (+) Case carrier for Vario case, including fasteners 71 60 7 696 301 £144 / G (+) Lock barrel, complete, for 2 cases 51 25 7 688 566 £20.80 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 2x) 51 25 7 681 199 £33.59 (o) Lock-barrel set 51 25 7 698 202 £15.20 / I Liner for Vario case, left 71 60 7 687 610 £67 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Vario topcase, black 71 60 7 696 302 £225 / I (+) Luggage rack, large, for Vario topcase (including adapter plate) 71 60 7 696 303 £64 / I (+) Lock barrel for topcase 51 25 7 688 568 £12.50 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 1x) 51 25 7 681 199 £33.60 / I (o) Lock barrels for 2 cases and topcase 51 25 7 688 567 £29.10 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Backrest pad for topcase 71 60 7 688 877 £45 / I Luggage carrier, small 71 60 7 701 810 £42.90 / G Tank rucksack, waterproof 71 60 7 711 240 £130 / I Enduro rear softbag 71 60 7 711 245 £35.90 / I Sport softbag, small, 19 l 71 60 7 694 117 £102 / I Sport softbag, large, 51 l 71 60 7 693 567 £139 / I Stuffbag, waterproof, 53 l 72 60 7 653 818 £90 / I Luggage strap with pull-tight buckle 72 60 2 304 808 £6.30 / E Bungee-cord spider 72 60 9 057 579 £3.95 / E Design line Spray-guard extension, rear 71 60 7 695 031 £24.20 / I Sound components Akrapović sports silencer 71 60 7 713 339 *1 £475 / G Ergonomics and comfort line Windscreen, large, tinted 71 60 7 713 834 *1 £138 / I Windscreen, large, clear (standard for F 800 GS) 71 60 7 713 833 £127 / I Windscreen, small, clear (standard for F 650 GS) 71 60 7 713 296 £87 / I Centre stand (F 650 GS) 46 52 7 700 864 *2 £83 / I Centre stand (F 800 GS) 46 52 7 700 049 *2 £91.50 / I (+) Fasteners for centre stand (F 650 GS + F 800 GS) 71 60 7 706 738 £24.90 / I Seat, low, black, 790 mm (F 650 GS), 850 mm ( F 800 GS) 52 53 7 695 013 £174 / I Heated handlebar grips and switches (see electronic parts catalogue) Navigation and communication components BMW Motorrad Navigator III plus 2008 72 60 7 716 116 *1 £650 / I (+) Holder for BMW Motorrad Navigator 71 60 7 697 785 £45.80 / E (+) Securing screw (order 4 of) 32 71 7 652 161 £4.55 / I Connecting cable for BMW Motorrad Navigator 71 60 7 686 670 £55 / E TMC module for BMW Motorrad Navigator 72 60 7 702 687 *1/3 £111 / E Car kit for BMW Motorrad Navigator 72 60 7 703 996 *3 £60.50 / E Navigator carry-bag function 71 60 7 683 161 £49 / I Safety line Hand-protector bar 71 60 7 716 043 £57 / I (+) Countersunk-head screw (order 2 of) 32 71 7 712 836 £3.34 / E Hand protector, small 71 60 7 705 963 £19.50 / I Hand protector, large 71 60 7 715 135 £23.10 / I Protector-mounted spoiler for hand protector, large 71 60 7 705 964 £15.20 / I Crash bar, left 71 60 7 699 437 £104 / I Crash bar, right 71 60 7 699 438 £104 / I (+) Fasteners for crash bar 71 60 7 702 395

1969-1978 BMW Motorrads LED Blinker Conversion Kit Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
Disassemble all 4 blinker light assemblies as shown in Figure 2 to start the installation. Be sure to remove the lens, gasket, and bulb/reflector assembly completely. Be sure to remove the wires from the reflector assembly prior to removal from the housing. The reflector assembly will not be used any further, keep in a safe place to be stored, if desired. Figure 3 2. Figure 3 (left) shows the function with their labels on the screw terminal block locations. If planning to use the “Running Light” feature, an additional wire might be needed to be installed to use this option. If you desire to use the “Running Light” function of these LED Boards, please refer to section “How to Use the Running Light Feature of the CD1007s”for complete instructions. 3. Pull out the existing wires far enough so that they can easily reach the terminal block. Insert the correct wire in the correct location of the terminal block. Using a jeweler flat-blade screwdriver, tighten the screw to secure the wire in its location. It is highly recommend to keep the terminal block to end of the signal housing facing outward of the motorcycle, as illustrated in Figure 3 (right). Model: CD1007, LED Blinker Conversion Kit Installation Instructions For 1969-1978 BMW Motorrads: Disclaimer: Under no circumstances will Bulbsthatlast4ever or it’s representatives be responsible or liable for any incidental or consequential property damages or personal injuries arising from or in connection with the use or installation of any of the listed foregoing products or devices. Rev. 6/10 Figure 4 4. Install the screws into the lens, then place an o-ring over each screw, as illustrated in Figure 4 (left & right). The o-rings will prevent the LED Board from moving around due to vibration

Suspension Basics for BMW Motorcycles

0

Filed Under (BMW) by admin on 30-11-2010

download
tires: Tires are the first part of any suspension system. The design of the tire and even the pressure you run can have a profound affect on the way your motorcycle handles. Stiff, low profile tires will give a sharper feel to the bike, as will higher tire pressures. Those of us who ride our GS’s off the road will decrease the tire pressure to about 50% of the street spec when we are in the dirt. The tire then becomes a very active part of the suspension, but will wallow like an old pig if not re-inflated when pressed back into pavement duty. It still surprises me when we have a customer complain that his BMW needs new shocks when they come in with nearly flat tires. It is possible that the best dollars-per- unit improvement you can make to your BMW may be in keeping the tires inflated. Chassis: There is not much that we can do about the chassis design, unless we are Troy the Welder, but it is a fact that different frames and swing arms flex differently and therefore are part of the suspension. On the Airheads, we often braced various parts of the frame and swing arms, resulting in improved handling that even mere mortals could appreciate. On the latest BMW’s it would take the likes of a Valentino Rossi to even notice if the parts were stiffened. Stiffer is not always better. One of the Japanese racing bike manufactures controls the stiffness of the frame in various areas to allow some flex for better handling. So, Mr. Rossi might not even like it if Troy stiffened his new BMW. Springs: Springs control the ride height of the motorcycle and the ability to allow for different loads. On most BMW’s there is a way to adjust the spring preload to some extent so that the ride can be optimized for a light rider or two-up operation with luggage. Dampers: Dampers control the speed and frequency at which the suspension operates by changing the kinetic (moving) energy to thermal (heat) energy. Without the damper, the suspension would oscillate as each movement occurred, resulting in decreased vehicle control. Dampers on BMW’s fall into two main groups. On airheads, older K bikes, F and G models, and the R1200 HP-2, the front dampers are integrated into the forks. On the rear of the above mentioned -3 – models, and on both ends of all the rest of the bikes, there is a more common shock absorber, around which the spring is located. The HP-2 uses an air spring and air dampened rear shock. Seat: OK, folks, this is here for my old buddy Jeff. We know that a seat isn’t part of suspension, but a bad one sure can make you miserable. We have sent dozens of seats to our friend Mike Harris for inexpensive mods that might improve your riding enjoyment more than any suspension changes you could make! Let us know if we can help you with this most important item

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SPORT LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
INSTALLATION NOTE Cover the rear fender with a clean shop towel to prevent scratching. Damage to the finish could result. 1. See Figure 1. Remove the four button-head TORX screws attaching the sissy bar (5) to the sideplates (4). Discard the screws 2. Remove the sissy bar and set it aside. For Rigid-Mount Sideplates only: Loosen, but do not remove, the hardware securing the sideplates to the motorcycle. 3. Position the luggage rack between the sideplates. Reinstall the sissy bar into the sideplate channels. 4. Apply Loctite 271 (Red) to the flat head TORX screws (2) from the kit, and insert through the holes in the luggage rack (1), sideplate, and sissy bar. Tighten the screws to 8-10 ft-lbs (10.8-13.6 Nm) . For Rigid-Mount Sideplates only: Apply Loctite 271 (Red) to the screws securing the sideplates to the motorcycle, and tighten to 21-27 ft-lbs (28.5-36.6 Nm) . 5. Remove the backing strip from the two rubber bumpers (3) and install onto the luggage rack. a. Align the notches in the bumper with the bottom edge of the channel on the sideplate. b. Wrap the bumper up the side of the luggage rack channel and across the bottom of the sissy bar. When properly installed the bumpers will cover the lower flat head screws, and will bend around the lower edge of the channel. Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) NOTE Maximum luggage rack weight capacity is ten pounds (4.5 Kg)

HARLEY DAVIDSON FXSTD PASSENGER BACKREST AND LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) INSTALLATION Passenger Upright 1. Unscrew the captive screw fastening the seat rear bracket to the fender. 2. Remove the rubber plugs from the three holes in the rear fender where the passenger upright installs. 3. See Figure 2. Fasten the studplate (2) to the fender (A) with the backing plate (3) and three flange locknuts (4). 4. See Figure 1. Fasten the passenger upright (3) to the studplate (1) with three flange locknuts (2). 5. Insert the seat front bracket into the frame, then fasten the seat rear bracket to the fender. NOTE The seat must be temporarily bowed up in the center to fit the seat rear bracket through the slot in the passenger upright. 6. Kit 51144-02 only. See Figure 2. Carefully clean the lower hole (B) on the passenger upright (1) with isopropyl alcohol to remove any grease or dirt. Remove backing from adhesive emblem (5) and press the emblem firmly in to place. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 1 4 3 2 is03890 1. Stud plate 2. Locknut, flange (3) 3. Passenger upright 4. Backrest pad Figure 1. Passenger Upright, Backrest Pad and Luggage Rack Installation NOTE When temporarily removing the passenger upright, the mounting and backing plates may be left in place to simplify passenger-upright re-installation. Thread the flange nuts back onto studs to store the nuts. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Backrest Pad See Figure 2. Fasten the backrest pad (7) to the passenger upright (1) using the button-head screw (6) as shown. Luggage Rack NOTE See Figure 2. Fasten the luggage rack (8) to the backrest with the backrest pad (7) removed from the studplate (2). -Fasten the luggage rack (8) to the passenger upr ight (1) using the luggage-rack mounting plate (11), button-head screw (12)

Incoming search terms: