bolt thread direction honda rancher clutches

You search Auto repair manual PDF bolt thread direction honda rancher clutches, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bolt thread direction honda rancher clutches Direct Download speed 5282 Kb/s

  bolt thread direction honda rancher clutches Full Version speed 6162 Kb/s



2008 Kawasaki ZG1400 Concours ABS Front 3-Line Kit and FK003D625R Single Line Rear INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our front brake line kit: You should have three (3) hoses, one (1) double banjo bolt, and two (2) single banjo bolts There are also a total of nine (9) washers and (3) brass conic inversors. Seven (7) washers and two (2) inversors will be used; the rest are spares. If you have purchased a rear kit as well, locate the following additional pieces: One (1) hose with bracket and c-clip attached, one (1) single banjo bolt, two (2) brass inversors and three (3) washers. You will use one (1) “olive” conic inversor and two (2) washers, the rest are spares. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. On the front brake line kit, we are replacing three hoses and their respective blocks (see pictures 1-2 for blocks) . For the rear, we are replacing one hose from the master cylinder to the ABS hard line. Take note of how the stock system was routed, in case you need to reinstall it. Step 4: Locate Line A – This will travel from the master cylinder to the ABS Junction. (See picture 3) You will use a single banjo bolt and two washers at the master cylinder, and an “olive” inversor to thread female end to hard pipe for incoming ABS (right side). * We have replaced the block at the upper triple clamp with a c-clip; please use your stock bolt to thread this in. (See picture 4) Locate Line B – This will travel from the ABS Junction to the right caliper. First, thread the female end to the hard pipe for outgoing ABS (left side). There will be a bolt from the OEM blocks at ABS Junction; please use this to thread c-clips into frame as shown in picture 5 . There is another bolt/OEM block located at the lower triple clamp; please use this to thread the c-clip in as seen in picture 6. Locate Line C – This will cross over the front fender using OEM holders, from right caliper to left caliper. Thread caliper banjos from Line B and C using the following sequence: double banjo hex, washer, 40- degree banjo from Line C, washer, 20-degree banjo from Line B, washer, caliper. Please see pictures 7 and 8 for reference. Thread single banjo bolt into left caliper, using two washers and 40-degree banjo. If applicable, locate rear Line D – this will travel from the rear master cylinder to the hard line for ABS. Thread the hard pipe into female end using a “olive” inversor, and attach bracket to swingarm as seen in picture 9 . Use the bolt from the holder for ABS hose, and sit our bracket on top of the OEM holder. Using the bolt from the OEM ABS hose holder in location shown in picture 10 , attach the c-clip on top of holder and tighten. Finally, thread 30-degree banjo in caliper using the following sequence: single banjo hex, washer, banjo, washer, caliper

Incoming search terms:

HARLEY DAVIDSON PIVOT BOLT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
This kit fits all 2004 and later XL (Sportster®) model motorcycles INSTALLATION Right-Side Pivot Bolt Cover Installation Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. See Figure 1. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns. 2. Note the position of the bottom-most flat on the rear-fork pivot hex-head bolt (3). Line up the pivot bolt cover over the bolt head so the set screw is centered on the hex flat. Use the 3/32 inch hex key from the kit to tighten the set screw securely to the head of the rear-fork pivot bolt. 3. Make sure the pivot bolt cover is clean and free of any oil or grease. Remove the protective backing from the adhesive disk on the back of the decorative insert (9). Install the decorative insert onto the end of the pivot bolt cover with the image or text upright and parallel to the ground. Press the insert firmly against the end of the pivot bolt cover and hold pressure for 30 seconds. After releasing pressure, avoid direct contact with the insert for about 20 minutes. Left-Side Pivot Bolt Cover Installation 4. Models without passenger footrests: Use an 8 mm hex key to remove the bolt (5) retaining the double-tube clamp (4). Models with passenger footrests: Use an 8 mm hex key to remove the two bolts (5) and the left-side passenger footrest and bracket assembly (6). 5. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns

1995 – 1999 HONDA CBR 900RR AKRAPOVIC BOLT-ON STREET LEGAL EXHAUST SYSTEM Installation instructions

0

Filed Under (Honda) by admin on 12-12-2010

download
REMOVAL OF STOCK EXHAUST SYSTEM 1. put the motorcycle on a side stand, we recommend a racing stand 2. unscrew and remove bolts from the muffler at the muffler – link pipe (header assembly) connection (Figure 1) 3. unscrew and remove the bolt from the metal hanging bracket and remove the muffler (Figure 2 & 3) INSTALLATION OF THE AKRAPOVIC BOLT-ON EXHAUST SYSTEM installing the muffler: 1. remove the stock gasket and install the copper gasket from the Akrapovic kit in the groove in the CNC ALU flange (Figure 4) 2. correctly orient the muffler and place it near the link pipe/header assembly 3. when the muffler and the link pipe are together, attach using the titanium bolts from the Akrapovic kit. Coat each bolt individually with bolt sealant before installing. (Figure 5) Tighten the bolts only hand tight – do not fully tighten! (Figure 6) 4. correctly position the carbon-fiber clamp and slide it onto the muffler – bear in mind the left offset of the carbon-fiber clamp viewed from the rear (Figure 7). WARNING: open the clamp to slightly wider than the diameter of the outer sleeve of the muffler – do not scrape it along the muffler outer sleeve! (Figure 8) 5. tighten the carbon-fiber clamp onto the stock bracket on the frame – use the stock bolts or the replacements from the Akrapovic kit, if supplied (Figure 9) 6. make sure that the BOLT-ON system is not touching any other parts of the motorcycle ! 7. example of the correct position of the installed Akrapovic BOLT-ON system (Figure 10) final installation: 1. Tighten the titanium bolts on the CNC ALU flange at the muffler – link pipe connection and also tighten the bolts on all of the brackets and clamps to which the exhaust system and the other dismounted parts of the motorcycle are attached 2. clean grease spots: a. muffler – titanium outer sleeve: use a soft cloth sprayed with a multi-purpose spray lubricant (WD-40 or equivalent) b. muffler – carbon-fiber outer sleeve: use a soft dry cloth Cleaning will prevent spots from burning onto the surface. Do not use aggressive chemical cleaners, because they can damage the sticker. 3. Check the operation of the brakes and suspension. Make sure all the bolts are sufficiently tightened. In case the exhaust system touches the cowling or other parts repeat the adjustment of the exhaust system or contact your authorized dealer.

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

Honda VT1100C Shadow, Aero, Sabre SPECIFIC-FIT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets TIP: Use soapy water to lubricate the grommets so they will slip into the holes in the bag. The vehicle images in this instruction set may be different than your motorcycle. Continued on next page… 3 Lay a support 7 (with the joint towards the rear of the bag) on the back of a bag. Temporarily put the mounting bolts 8 through the support’s holes and into the plas- tic spacers in the grommets. Place one of the support clips 9 over the center of the lower portion of the support, so the two holes in the clip align with the predrilled holes in the bag. Use the 3/16” screws and nuts from the hardware kit to attach the support clip to the backup plate inside the bag. Place the nuts on the outside of the bag. Do not over- tighten the hardware, as this may cause damage to the saddlebag. Remove the mounting bolts from the support and the plastic spacers

Incoming search terms:

HARLEY DAVIDSON REAR SWINGARM AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) NOTE XL Sportster 883 and XL1200R models may require loosening or removal of the rear muffler in order to install the right side rear axle cover. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. 1. Support the vehicle, and loosen or remove the rear muffler if necessary. XL Sportster 883 and XL1200R models: Remove the right-side lower shock absorber mounting bolt. Save for re-installation. All other models: Remove and discard the right-side lower shock absorber mounting bolt. 2. Swing the bottom of the shock absorber out of the way. Position the right-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 3. Reposition the shock absorber. XL Sportster 883 and XL1200R models: Install the shock absorber mounting bolt removed in Step 1. All other models: Install the shoulder bolt (3) from the kit. All models: Tighten the bolt to 45-50 ft-lbs (61-68 Nm) . NOTE When torquing the bolt, align two of the bolt-head flats parallel to the ground. This will allow proper orientation of the bar and shield logo on the bolt cover. 4. Position the bolt cover (4) over the bolt head (3) with the Bar-and-Shield logo oriented upright, and lock in place with the set screw (5). Tighten securely. Reposition and tighten the muffler per the Service Manual instructions. 5. Remove and discard the left-side lower shock absorber mounting bolt. Move the bottom of the shock absorber out of the way. Position the left-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 6. Reposition the shock absorber and install the shoulder bolt from the kit. Tighten to 45-50 ft-lbs (61-68 Nm) , aligning two of the bolt head flats parallel to the ground. 7. Position the bolt cover over the bolt head with the Bar-and- Shield logo oriented upright, and lock in place with the set screw. Tighten securely

Ducati Sport Clutch Lever INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 26-10-2010

download
1 To remove your stock lever, use a 19mm wrench or (adjustable wrench) to remove the large sheet metal nut attached to the main pivot bolt that holds the lever. (Photo 1a) Once the locknut is removed, push the main pivot bolt out with your finger or if necessary tap lightly with a rubber mallet or plastic handle end of a screwdriver (Photo 1b) After the pivot bolt is removed, the lever will detach from the master cylinder. (Photo 1c) 1a See other side for further instructions INSTALLATION INSTRUCTIONS FOR PART # CRC552 ® C/5 Sport Clutch Lever Part # CRC552 1b 1c INSTRUCTIONS_CRC552 12/27/07 10:05 AM 23 4 2 Included with your ASV lever is a plastic bag that contains a custom pivot bolt, spacer & locknut. These parts will replace the OEM Brembo parts that were used with your stock lever. 3 Carefully place the lever into the master cylinder while aligning the plunger rod into the plunger cup on your ASV lever as shown in photo 3. 4 Align the lever and the master cylinder pivot bolt holes and Install the main pivot bolt, you will need to pre-load the lever into the master cylinder to get the bolt through the holes. The bolt head has two cut outs on the sides that need to be aligned with the matching area on the master cylinder. Be sure the head of the bolt seats down into the slotted area of the master cylinder. It may be necessary to use a rubber mallet or Plastic end of a screwdriver (Photo 4) to tap the head of the bolt down into its slot. 5 On the other side of the pivot bolt where the threads are, you will see that there is space around the pivot bolt. You will need to install the aluminum spacer that was supplied in the plastic bag with the pivot bolt and locknut. The spacer has a small flange on one side. The flange should be on the outer side when installing it into the hole surrounding the bolt. (Photo 5a) You may need to use pressure to seat the spacer fully into the hole surrounding the pivot bolt. You should be able to do this by using your fingers or thumbs as shown in photo 5b.

HONDA TRX 650 RINCON 4X4, TRX 680 Rincon BLADE HARDWARE MOUNTING REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 26-12-2011

download
Push tube/ Swivel/ Blade Assembly Instructions 1. Install the blade swivel (15) onto the front of the push tube (14) using the 1/2″ shoulder bolt (4), two 1/2″ washers (5), and a 3/8″ Nylock nut (3) from the bolt bag per diagram #1. Make sure the flat washers seat properly on the bottom of the shoulder bolt while tightening the nut. Make sure the blade turns freely. 2. Remove the 2 bottom flanged nuts (I) from the u-bolt (D) and 2 from the 3/8″ bolts (H) on the blade position pin assembly (23). Run the 2 top flanged nuts up the threads of the u-bolt. Place the blade position pin assembly on the push tube as shown in the Diagram, sliding the blade position pin through one of the oval holes on the swivel and through the rear blade position pin support bracket on the push tube. 3. Re-install the u-bolt and 3/8″ bolts and flanged nuts per the Diagram. On the u-bolt, thread the bottom nuts up until they are flush with the bottom of the threads then run the top ones down, making sure the bottom nuts remain flush with the bottom of the u-bolt. Tighten all 4 bottom nuts. 4. Remove the two shoulder bolts (18) from the pivot point brackets on the back of the blade (1). Attach the blade to the swivel by sliding the ears on each side of the swivel into the pivot point brackets on the blade, reinstall the two shoulder bolts and Nylock nut (3) and tighten. 5. Hook the blade springs (6) to the two round holes on either side of the 5 oval holes on the swivel. Hook the eyebolts through the other end of the springs, push the eyebolts through the spring attaching points on the back of the blade and install 3/8″ Nylock nuts (3). Spring tension may be increased by tightening both Nylock nuts on the eyebolts evenly. 6. Install the blade stops (16) with the two 3/8″ x 1″ bolts (17) and 3/8″ nuts (3) per the Diagram. Rotating the stops allows you to change the blade pitch to suit changing conditions or materials

Incoming search terms:

HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

Incoming search terms:

Incoming search terms: