boulevard m50 f1 after rain

You search Auto repair manual PDF boulevard m50 f1 after rain, if there are search results will appear below. If search results do not exist, please search by others keyword.



  boulevard m50 f1 after rain Direct Download speed 5282 Kb/s

  boulevard m50 f1 after rain Full Version speed 6162 Kb/s



TOYOTA PREVENTION AND REPAIR OF ACID RAIN DAMAGE ( REVISED)

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
it is the responsibility of the dealer to protect and maintain the quality of the vehicle’s finish after receipt at the dealership. Frequent vehicle washing, up to 4 times weekly during high heat and humidity periods, should be performed to minimize the potential for paint damage due to acid rain exposure. This is especially important in areas known for high frequency and concentration of acid rain and industrial fallout. INSPECTION AND REPAIR: Acid rain damage can frequently be identified on vehicles by the presence of visible spots on the paint surface which resemble hard water stains. Unlike water spots, however, acid rain damage cannot be removed by polishing or buffing only. Because acid rain can etch and soften the paint, normal polishing or buffing repair procedures should not be attempted, as this will result in visible depressions in the paint surface. CORRECTIVE ACTION: The repair of acid rain damaged paint surfaces varies depending on how deep the acid has penetrated. Superficial damage can usually be removed by color-sanding and polishing. If the damage extends to a depth greater than 1/2 mil of the clearcoat on a pearl or metallic color, or more than 1 mil of a solid color, sanding and repainting may be necessary. Unfortunately, there is no simple method of determining the actual extent of the acid penetration other than color sanding a representative affected area until there is no visible etching or depressions and then measuring the amount of paint removed with a magnetic type paint film thickness gauge

Suzuki C50/ M50 Boulevard BIG AIR KIT INSTALLATION

0

Filed Under (Suzuki) by admin on 13-03-2012

download
1. Remove the (2) Bolts at the top of the stock air cleaner to the left and right of the oval rubber hose coming from under the fuel tank. 2. Loosen the hose clamp at the base of the oval rubber hose on the top of the air cleaner. 3. A male barb protrudes from the rear of the air cleaner that inserts into a rubber grommet mounted to the cylinders. Pull the air cleaner away from the cylinders firmly and you will feel the barb release. Now pull the upper section of the air cleaner downward to remove it from the oval snorkel tube from under the fuel tank. 4. Now you can reach to the rear of the box and unplug the electrical lead for the Air Sensor” which sits just about in the middle of the rear of the air cleaner. Now remove the breather hose at bottom of the air cleaner. 5. Set the air cleaner aside and turn it over to access the back. Remove the single bolt that secures the Air Sensor” (This sensor will be installed into the Aluminum Manifold of your new BAK assembly later) 6. Remove the lower mounting arm assembly from the cylinders. (You will not reuse this). 7. Using the (2) Dome head m6 x 15mm screws install the (2) #1 Arms to the rear (the side without the groove) of the backing plate, the shiny/chrome side of the arms should face outward. The smaller of the two holes in each arm is the one you place the screws through. Use the m6 Flange Nuts to secure the bolts at the rear of backing plate. Snug these up but do not tighten fully.

Incoming search terms:

SUZUKI VOLUSIA 800, C50, M50 Left/ Right Saddlebag Installation Manual

0

Filed Under (Suzuki) by admin on 14-11-2010

download
Your saddlebag supports will install in just a few minutes using common tools. Read all instructions carefully and completely before installing your new saddlebag supports. 1. Remove your stock fender rail bolts. 2. Install your Cobra saddlebag supports using the supplied 8mm x 65mm button head bolts (where the stock bolts were removed), the saddlebags should hang towards the rear and away from the motorcycle. 3. Torque bolts to factory specifications Cobra recommends you always wear a helmet while riding. Please never operate your motorcycle while under the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely

Incoming search terms:

SUZUKI M50 / C50 Fuel Injected Models INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 19-02-2012

download
1. Remove seat and left side covers. 2. Remove fuel tank. We highly recommend you consult the factory service manual for proper removal of fuel tank. Remove fuel tank rear mounting bracket 3. Route wiring harness under frame by fuel tank rear mounting bracket and up left side of the engine. (Fig. 1) 4. Unplug the TPS connector (black) and connect the two white 3-pin connectors in-line with the factory TPS connector. (Fig. 2) 5. Disconnect the factory connector from rear injector and connect to Fuelpak connector. (Fig. 3) 6. Connect other Fuelpak connector to injector. (Fig. 4) 7. Route black wire to battery negative connection as shown. (Fig. 5) 8. Attach Fuelpak to Fuelpak harness and mount next to battery with Velcro. (Fig. 6) 9. Follow the service manual to reinstall the fuel tank.

Incoming search terms:

SUZUKI BOULEVARD M109R Fuel Injected Models INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 16-02-2012

download
1. Remove seat, right and left side covers, and fuel tank. 2. Remove airbox. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness as shown in the picture. (Fig 1) 4. Unplug stock wiring harness from injectors and plug in the connectors from Fuelpak as shown. (Fig 2) 5. Unplug the TPS connector (grey) and attach T-tap connectors to the two outside wires. (Fig 3) 6. Route Fuelpak green wire to T-tap on the factory black wire with brown stripe. Routh the Fuelpak violet wire to T-tap on the factory pink wire with black stripe as shown (Fig 3) 7. Reattach the TPS connector. 8. Route red wire to the front of engine and down to the horn. (Fig 4) 9. Disconnect the two position connector from horn and snip connector in half so you have two one-wire connections. 10. Reattach factory grey wire to horn. Attach Fuelpak red wire to the other horn connection. Plug the factory horn orange wire to the male connection on the Fuelpak red wire. 11. Route black wire to battery negative connection as shown. (Fig 5) 12. Attach Fuelpak to Fuelpak harness and mount to bracket under the left side cover as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the red wire connection on the horn and that it is connected to the orange wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank.

HARLEY DAVIDSON LUGGAGE RACK BAG INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION 1. Set the rack bag on top of the luggage rack with the main pocket opening facing the rear of the vehicle. 2. See Figure 2, Figure 3 and Figure 4. Determine which luggage rack is installed on the vehicle. 3. See Figure 1. Open the hook-and-loop closures in the appropriate locations for the installed luggage rack. 4. Fasten the closures around the bars of the luggage rack and pressing the hook-and-loop ends together. 5. Give the rack bag a final pull to verify the pack is securely attached. 1 2 3 4 7 5 6 is05516 1. Rear left closure 2. Rear center closure 3. Rear right closure 4. Front left closure 5. Front center closure 6. Front right closure 7. Rain cover storage Figure 1. ook-and-Loop Closure Locations 1 2 3 4 5 6 is05513 Figure 2. Premium Rack Closure Locations -J00861 1 of 2 1 3 4 6 is05514 Figure 3. Air Wing Rack Closure Locations 2 5 4 6 is05515 Figure 4. Contoured Rack Closure Locations USAGE Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) •Combined load of top rack and Tour-Pak® must not exceed 25 lbs (11.3 Kg). Overloading the motorcycle will cause unstable handling and reduced braking efficiency, which could result in death or serious injury. See Figure 1. Open the hook-and-loop flap on the rain cover storage pocket (7) and wrap the tethered rain cover around the bag.

K- Drive removable Click & Lock Saddlebag sets for Kawasaki VN 1600 Classic

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
K-Drive Click & Lock saddlebags are completely reinforced : – Backside : made of a strong hdpi plate; – Upper side, sides and bottom are reinforced with PVC at the inside : – Side flaps are closed with velcro for better protection against the rain. Click & Lock saddlebags have discrete “sliding” grips All buckles, logo & decorative studs are made of “zamack”. A material which is 100% rustfree For maximum protection against the rain, the sideflaps are closed with Velcro

K-Drive Click & Lock Saddlebag sets for Triumph Rocket 3

0

Filed Under (Triumph) by admin on 06-11-2010

download
K-Drive Click & Lock saddlebags are completely reinforced : – Backside : made of a strong hdpi plate; – Upper side, sides and bottom are reinforced with PVC at the inside : – Side flaps are closed with velcro for better protection against the rain. Click & Lock saddlebags have discrete “sliding” grips All buckles, logo & decorative studs are made of “zamack”. A material which is 100% rustfree For maximum protection against the rain, the sideflaps are closed with Velcro K-Drive Click & Lock saddlebags are fixed to the saddlebagguards by means of a lockable clicksystem. This “Click & Lock” system has many advantages: – Our bags are easily mounted and removed in just a few seconds. – The bags themselves are locked to the motorcycle with a key. – The bags don’t touch the bike and therefore don’t damage it. – They can also be attached to motorcycles without a duo saddle. – As the bags are made specifically (or adapted) for a model, every bag we manufacture fits perfectly. – Our saddlebag holders are discreet, following the contour of the motorcycle, and are perfectly chromed K-Drive is a trademark of Vartex bvba * Iparex is a very strong synthetic leather, made following our technical specifications. It has a luxury leatherlook and is one of the best materials for saddlebags. It is strong, waterproof and don’t need any maintaining. To clean it, just use water, eventually with a light natural soap. Never use any product that is meant for leather, it may harm the Iparex.

K-Drive removable Click & Lock Saddlebag sets for Kawasaki VN1500/ 1600 Mean Streak

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
Each saddlebagsset is supplied in an individual packing, containing : – 1 pair of click & lock saddlebagsupports; – 1 pair of saddlebags with our clicksystem mounted on the rigid backside of the bags; – All necessary bolts; – 2 keys to lock the bags to the supports. (lock is at the inside of the bags) – 2 keys to lock the bags (only CL bags) . K-Drive Click & Lock saddlebags are fixed to the saddlebagguards by means of a lockable clicksystem. This “Click & Lock” system has many advantages: – Our bags are easily mounted and removed in just a few seconds. – The bags themselves are locked to the motorcycle with a key. – The bags don’t touch the bike and therefore don’t damage it. – They can also be attached to motorcycles without a duo saddle. – As the bags are made specifically (or adapted) for a model, every bag we manufacture fits perfectly. – Our saddlebag holders are discreet, following the contour of the motorcycle, and are perfectly chromed K-Drive is a trademark of Vartex bvba * Iparex is a very strong synthetic leather, made following our technical specifications. It has a luxury leatherlook and is one of the best materials for saddlebags. It is strong, waterproof and don’t need any maintaining. To clean it, just use water, eventually with a light natural soap. Never use any product that is meant for leather, it may harm the Iparex. K-Drive Click & Lock saddlebags are completely reinforced : – Backside : made of a strong hdpi plate; – Upper side, sides and bottom are reinforced with PVC at the inside : – Side flaps are closed with velcro for better protection against the rain. Click & Lock saddlebags have discrete “sliding” grips All buckles, logo & decorative studs are made of “zamack”. A material which is 100% rustfree For maximum protection against the rain, the sideflaps are closed with Velcro

K-Drive Click & Lock Saddlebag sets for Triumph Bonneville America And Speedmaster

0

Filed Under (Triumph) by admin on 06-11-2010

download
Each saddlebagsset is supplied in an individual packing, containing : – 1 pair of click & lock saddlebagsupports; – 1 pair of saddlebags with our clicksystem mounted on the rigid backside of the bags; – All necessary bolts; – 2 keys to lock the bags to the supports. (lock is at the inside of the bags) – 2 keys to lock the bags (only CL bags) . K-Drive Click & Lock saddlebags are fixed to the saddlebagguards by means of a lockable clicksystem. This “Click & Lock” system has many advantages: – Our bags are easily mounted and removed in just a few seconds. – The bags themselves are locked to the motorcycle with a key. – The bags don’t touch the bike and therefore don’t damage it. – They can also be attached to motorcycles without a duo saddle. – As the bags are made specifically (or adapted) for a model, every bag we manufacture fits perfectly. – Our saddlebag holders are discreet, following the contour of the motorcycle, and are perfectly chromed K-Drive is a trademark of Vartex bvba * Iparex is a very strong synthetic leather, made following our technical specifications. It has a luxury leatherlook and is one of the best materials for saddlebags. It is strong, waterproof and don’t need any maintaining. To clean it, just use water, eventually with a light natural soap. Never use any product that is meant for leather, it may harm the Iparex. K-Drive Click & Lock saddlebags are completely reinforced : – Backside : made of a strong hdpi plate; – Upper side, sides and bottom are reinforced with PVC at the inside : – Side flaps are closed with velcro for better protection against the rain. Click & Lock saddlebags have discrete “sliding” grips All buckles, logo & decorative studs are made of “zamack”. A material which is 100% rustfree For maximum protection against the rain, the sideflaps are closed with Velcro