brute force 650 carb removal

You search Auto repair manual PDF brute force 650 carb removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  brute force 650 carb removal Direct Download speed 5282 Kb/s

  brute force 650 carb removal Full Version speed 6162 Kb/s



KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

KAWASAKI Brute Force 750i, 650 4x4i BACK BUMPER MOUNTING INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
KAWASAKI Brute Force 750i, 650 4x4i Ref. Item Description Item # Qty 1 Back Bumper 166-236 1 2 Attachment A32 2 3 Bolts 2″ x 5/16″ (Hex) ZZZ-H0425 2 4 Bolts 1 1/2″ x 5/16″ (Hex) ZZZ-H0424 2 5 Bolt ¾” x 5/16″ (Hex) ZZZ-H0423 2 6 Flat Washer 5/16″ 146-016 6 7 Lock Nut 5/16″ 0404-90239 6

Incoming search terms:

BMW F 650 CS Rear belt wheel cracks Removal And Installation Manual

0

Filed Under (BMW) by admin on 12-11-2010

download
Relieve the tension of the toothed belt and lift the belt off the belt wheel (refer to F 650CS Repair Manual, 00.57). 2) Remove 6 screws (see arrow in photo at right). 3) Remove the rear belt wheel. 4) Clean and degrease the tapered bores and the threads of the mounting screws 5) Carefully place the new belt wheel in position on the damper, coat the screw threads with Loctite 243 and hand tighten the securing screws. 6) Tighten the securing screws to the specified torque maintaining a diagonally opposite tightening sequence throughout (Torque to 28 NM, curing time 12 hours). 7) Measure the vertical runout of the belt wheel (refer to F 650 CS Repair Manual, 33.15). 8) Install and adjust the rear drive belt (refer to F 650 CS Repair Manual 00.57 – 00.58) 2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure.

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Incoming search terms:

Single-Cylinder BMW G 650 X Model Series

0

Filed Under (BMW) by admin on 16-11-2010

download
introducing the new range of single-cylinder models, BMW Motorrad is broadening its model line-up with a clear focus on additional target groups. Proceeding from the same technical foundation, the Company has created three new motorcycles absolutely different in their features and characteristics: the G 650 Xchallenge Hard Enduro, G 650 Xmoto Street Moto, and the G 650 Xcountry Scrambler. With their outstanding product substance, their purist looks, and their exceptionally sporting riding characteristics, these single-cylinder models are filling attractive niches in the market. And through their low unladen weight of less than 160 kg or 353 lb according to the DIN standard, they offer dynamic performance for both the connoisseur and the sports-minded rider. Market launch of the new G 650 X model series is planned in good time for the beginning of the season in spring 2007. These new machines with the smallest engines in the BMW model range offer particularly the young and young-at-heart motorcycle rider exactly the right entry into the world of BMW motorcycles, but are not entry-level bikes in the conventional sense of the word: On the contrary, the G 650 Xchallenge Hard Enduro will thrill the customer who wishes to really benefit from the enormous offroad potential of his machine. The G 650 Xmoto Street Moto, in turn, with its very impressive active riding qualities, offers the genuine enthusiast a new dimension in riding pleasure. The G 650 Xcountry Scrambler, finally, stands for carefree riding pleasure and nimble performance both on the road and off the beaten track. Indeed, this unique machine is able to meet all kinds of requirements and offer virtually all riding qualities ranging from city use via country roads and small, winding lanes, all the way to offroad tracks presenting the most challenging requirements. The G 650 Xcountry therefore conveys the classic but relaxed feeling of riding a genuine Scrambler as well as the concept of “wandering” on your motorcycle into today’s world in a most modern style. And last but certainly not least, riding pleasure is guaranteed under all conditions and in every situation, since the G 650 Xcountry offers the same outstanding engine and running gear qualities as its two very sporting “sister models

Incoming search terms:

Kawasaki V-Force 700 Snorkel REMOVAL AND INSTALLATION

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove plastic from around air filter housing. Remove clamp attaching stock intake (snorkel) from air box. Loosen upper radiator hose clamp. Rotate it so the drive is on the opposite side of the new snorkel and retighten it. Loosen metal support for front plastic. Have a friend gently pull outward and carefully install the new snorkel. Position snorkel so it does not interfere with any cables or steering stem. Move handle bars back and forth. Check for clearance around new snorkel. Make sure all wires, cables and steering stem do not come into contact with the snorkel. Adjust as necessary. Tighten clamp at the air box. Reinstall plastic in opposite order of removal. At your own risk, you can cut slices in the black plastic hood on front of the quad to force the maximum amount of cold fresh air and produce additional horsepower. Jetting will vary from quad to quad and with the altitude

42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

YAMAHA V-Star 650 BIG AIR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 21-01-2012

download
Remove fuel tank and air filter assembly per Yamaha service manual procedures. 2. Remove the air silencer box under the tank. 3. Install supplied BA-2410-00 Needle/Jet kit according to the instructions in the jet kit package being sure to use the Jets and Needle Slot setting called out for the external BAK filter assemble. 4. Reinstall the air silencer box under the tank. 5. Remove the rubber boot from the stock air box. It is glued-in from the factory, but will come loose if gently persuaded. See photo #1 Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or fitment may be required. Barons bears no responsibility on installation costs associated with this product. © 2010 Barons Custom Accessories 7401 Slater Ave. Huntington Beach, CA 92647 (714)274-4065 – Ph. (714)848-0718 – Faxwww.baronscustom.comtech@baronscustom.com Page: 2 BA-2011-00/03/06/07/13/13B BIG AIR KIT – YAMAHA V-Star 650 6. Install the stock rubber boot into your new Baron air filter backing plate with the supplied glue. Squeeze glue liberally into sealing groove in stock rubber boot. See photo #2 Allow glue to set up and dry prior to mounting onto bike

Incoming search terms:

YAMAHA V-Star 1100 Carburetor Bowl Screw Repair and Removal After Stripping and Pilot Cap Removal

0

Filed Under (Yamaha) by admin on 19-01-2012

download
When I first started working on bike many years ago, I learned the danger of stripping the heads of Philips screws when removing or installing them on motorcycles. I remember the two worst screws were the casing side-cover aluminum screws and carburetor bowl screws. I think I tried every method of screw removal after they were stripped. Vice grips, better tipped screwdriver, hammer, drill, and other tools were used. One way I learned to remove stripped screws is to re-make the Philips head into a flathead screw. Cutting a slot in the top of the screw and then use a flat-head screwdriver to remove the screw. On some parts this technique can work, other parts and screws it may not. The Philips screws on the bottom of the V-Star carburetor bowls are VERY prone to stripping. In fact, I will not start a carburetor cleaning without new hex head screws to replace the original Philips bowl screws. Replace the bowl screws for yourself if you keep the bike, or for the next rider that will appreciate the hex-head screws when they clean the carburetors. Not many other parts on a V-Star have screws that are prone to stripping. This documentation is to help riders with motorcycle maintenance. Some riders will find themselves with the problem of removing stripped screws. A carburetor cleaning can quickly double in time when you realize the hardest part of the job is removing bowl screws after they strip. And then realizing you do not have the replacement hex-head screws available and must now go to the hardware store.

Incoming search terms:

Incoming search terms: