buell blast 500cc cluch

You search Auto repair manual PDF buell blast 500cc cluch, if there are search results will appear below. If search results do not exist, please search by others keyword.



  buell blast 500cc cluch Direct Download speed 5282 Kb/s

  buell blast 500cc cluch Full Version speed 6162 Kb/s



BUELL BLAST SS2-R Exhaust System Removal And Installation

0

Filed Under (Tips and Review) by admin on 18-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the two nuts that mount the header to the cylinder head. 2. Remove the rear muffler mounting bolts. Remove the bolt from the insulated mount at the front of the muffler. Save the nuts and bolts for reuse. 3. Remove the stock head pipe and muffler assembly. 4. Using circlip pliers carefully remove the circlip and flange from the stock exhaust system.Save for reuse. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Slide the circlip and flange over the VHR head pipe. NOTE: If the circlip looks bent or twisted replace it with a new circlip. 2. Slide the supplied clamp over the head pipe. 3. Install the head pipe into the exhaust port using the stock flange nuts. Leave finger tight at this time. 4. Bolt the head pipe clamp to the engine using the supplied bracket stamped #311. Refer to Fig. 1for the assembly order of the front mounting hardware. Leave loose at this time. 5. Slide the supplied clamp onto the notched end of the muffler assembly. 6. Slip the muffler assembly onto the head pipe. Bolt the muffler assembly to the original mounting points at the rear of the frame, using the supplied 5/16″-18×3/4″ socket head capscrews, stock nuts and washers. 7. Tighten the exhaust flange nuts and muffler clamp. 8. Tighten the two bolts that mount the muffler assembly to the motorcycle. 9. Be sure to tighten all hardware before starting your motorcycle. RE-JETTING INSTRUCTIONS Re-jetting the carburetor will result in realizing the “full” potential of this performance exhaust system. Vance & Hines offers jet kits for most applications

Ducati Monster 600/750/900; Buell S1, X1, M2, Blast Sequential LED Tail Light Installation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
1. Please use supplied sub harness to connect the sequential signals 2. Connect the blue and yellow wire on the shorter end of the sub-harness to the corresponding blue and yellow on the LED tail light. Make sure the connector is pushed all the way in and use the green covers to insulate. 3. Disconnect and remove factory signal lamps. We recommend one at a time. 4. Locate the longer end of the sub-harness and connect the blue/black wires to the left signal output and the yellow/black wire to the right signal output. 5. Insulate as necessary and cable tie any wires out of the way

BUELL XB9R REMOVABLE SADDLEBAG KIT Installation Instructions

0

Filed Under (Buell) by admin on 03-02-2011

download
Installation 1. Ensure that the tail section of the motorcycle is clean and dirt free. 2. See the Service Parts illustration. Using a T27 TORX drive head, remove the two screws holding the tail section underside shield. 3. Install the saddlebag bracket (3) as shown, reinstall the screws and tighten securely. Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. The mounted saddlebags will cover the factory-installed rear side reflectors on these vehicles. Reposition, or have a dealer reposition, the original rear side reflectors supplied with this motorcycle or apply new ones. If this is not done, the loss of visibility to other motorists may result in death or serious injury. NOTE New reflectors (Part number 59256-84A) are available from your Buell Dealer. NOTE When removing adhesive residue, take care to keep from scratching or damaging the reflector, mounting bracket or surrounding parts. 4. Use a thin flat blade, like that on an X-Acto knife, and carefully pry the reflectors off of their mounting brackets. Remove the adhesive residue from the brackets and the back of the reflector. 5. Mount the new reflector relocation brackets (4) to the stock reflector mounting brackets as shown. Attach each relocation bracket through the slots in the stock bracket with two screws, flat washers and lock nuts from the Hardware Kit (5). Slide the relocation bracket to the rearmost position and tighten securely. 6. Remove the outer release liner of the foam tape on the relocation bracket. Mount the stock reflector squarely to the bracket, and press firmly in place. 7. Remove the passenger pillion (and pillion cover, if mounted), and set aside. 8. Position one of the saddlebags to the side of the motorcycle tail section with the Buell logo facing out, and to the rear. Hook the mounting pocket on the back side of the bag onto the saddlebag bracket mounted earlier. Repeat for the other saddlebag. 9. Bring the saddlebag straps up and over the tail sectiion. Pull the right-side straps up through the buckle eyes on the left-side straps, remove any slack and fasten the hook-and-loop material. 10. Note the points where the saddlebags and straps contact the motorcycle tail section. Two lengths of clear protective tape have been provided in the Hardware Kit. If desired, cut and fit lengths of the tape to those areas of the tail section to prevent damaging the finish. 11. Replace the passenger pillion (and pillion cover if desired). Position the front tongue on the pillion overthe saddlebag straps

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

Incoming search terms:

Harley-Davidson S&S Super E and G Series Shorty Carburetors Installation and Jetting Instructions

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
throttle linkage with no cable modification. S&S Super E and G carb kits for 1936 to 1989 Big Twins contain a throttle cable guide (11-2339) designed for butterfly type throttle cables, and kits for 1990 and later Big Twins contain a taller throttle cable guide (11-2338) designed for CV type throttle cables. See Picture 2. The two throttle cable guides are interchangeable on the carburetor body, and can be changed very easily to update older carburetors or to accommodate custom throttle cables which are not stock for a particular year chassis. 1981 to Present Sportster Models Stock Sportster models from 1981 to 1987 have two cable throttle system designed for butterfly type carburetors. Sportsters from 1988 to present have a two cable throttle system designed for use with the stock constant velocity (CV) type carburetor. Since the taller #11-2338 cable guide bracket can not be used on a Sportster chassis due to insufficient frame clearance, throttle cables on Sportsters originally equipped with a CV type carburetor must be changed to butterfly style cables. S&S can supply the correct style throttle cables. See S&S Throttle Cable Application Chart. Picture 2 S&S THROTTLE CABLE APPLICATION CHART Length Total Housing Length Vinyl Housing Part Number Open Side Part Number Close Side Fitment 36″ 32″ #19-0430 #19-0431 For Buell with 7/8″ handlebars 36″ 32″ #19-0432 #19-0433 To ’95 ’81-’85 FX and FL; All ’81-’85 XL (Also pre-’81 w/2-cable throttle housing replaced.) For Buell with 1″ diameter handlebar 36″ 32″ #19-0436 #19-0437 ’96-Up 883-1200 XL 39″ 35″ #19-0434 #19-0435 To ’95 Softail (FXSTC, FXST, FLSTC, FLSTF) ’86-’94 FXR, ’93-’95 Dyna 39″ 35″ #19-0438 #19-0439 ’96-Up Softail (FXSTS, FXSTC, FLSTC, FLSTF) ’96-Up Dyna 42″ 38″ #19-0446 #19-0447 To ’95 custom application 42″ 38″ #19-0440 #19-0441 ’96-Up custom application 48″ 44″ #19-0462 #19-0463 To ’95 All FLT Models 48″ 44″ #19-0464 #19-0465 ’96-Up All FLT Models ” 1996 to Present Buells 1996 and 1997 Buells require special S&S butterfly style throttle cables for Buells, which are compatible with the stock 1996-1997 throttle assembly. 1998 and later carburated Buells require installation of stock 1996 – 97 throttle grip and the special S&S Buell style throttle cables when installing Super E or G carburetors. S&S Throttle Kits S&S throttle kits fit 1″ handlebars and can be used on most chassis. (An adapter sleeve is available for use with earlier, 7 ⁄ 8 ” OEM handlebars originally equipped with internal throttle cable.) Barrel fittings on S&S cables readily “plug in” to S&S Super E, G, and stock H-D 1981-’90 butterfly type carb throttle linkage. Kits include one opening and one closing side cable, left and right grips, and handlebar clamps. Kits with 36″, 39″, 42″, or 48″ length cables are available. Length specified refers to overall cable length. Vinyl covered outer housing is 4″ shorter than overall length

Incoming search terms:

Aermacchi IHRO1 Machine Specifications

0

Filed Under (Aermacchi) by admin on 13-11-2010

download
1. IHRO 1 caters for single cylinder thoroughbred Grand Prix racing motorcycles constructed during the period 1945-1972 inclusive, for the specific purpose of participation in Grand Prix competition during that era. Maximum capacity for any machine is 500cc, and wherever possible it is intended to run three classes, for machines up to 250cc, 350cc and 500cc. 2. Motorcycles must be presented in original, period condition, with no external updating. Period appearance seats, fuel tanks and fairings (if fitted) must be used. No external changes may be made to the appearance of any machine unless it can be proved that such a change was made in the period. Modern safety fixtures required by some federations and modifications mentioned in this document are not covered by this ruling. 3. No disc brakes are allowed. Drum brakes only may be used. 4. No alloy/magnesium wheels are allowed. Wire wheels only may be used. 5. All machines must have twin shock rear suspension: No monoshocks except Vincent Grey Flash. Suspension units must resemble period components, i.e. no external gas reservoirs etc. 6. All frames and swinging arms must conform exactly to period appearance; no box section swinging arms allowed unless fitted by the manufacturer to that machine in the period. 7. The maximum permitted rim width on either wheel is WM3. 8. No slick tyres, hand cut slicks or modern racing tyres designated by the manufacturer as being exclusively for wet weather use are permitted. Only the following rear tyres may be fitted. Any 19″ tyre. The following 18″ tyres, Dunlop 3.50×18, 3.50/3.25×18 KR124 and KR124A, Avon AM22 110/80×18 Rear Fitment and Avon AM18 120×18 9. Choice of carburettor is free, provided that this is of a period type cylindrical slide model, albeit of a later manufacture. Flat slide instruments are not permitted with the exception of Gardner carburettors. Fuel injection is not permitted except if it can be proved that particular motorcycle ran between 1945-72 with the same type of injection system fitted. A Wal Philips injector is classified under this heading. 10. The type of fuel used must conform to the ACU and FIM’s current fuel regulations for 100LL Avgas at 102 MON. See full specifications below. All machines must finish a race with a minimum of 2 litres of fuel in the tank to allow a sample to be taken for analysis. 11. The use of belt primary drives is encouraged.

S&S Super E and G Series "Shorty" Carburetors REMOVAL, Installation and Jetting Instructions

0

Filed Under (S&S) by admin on 29-10-2010

download
Remove Old Carburetor WARNINGS ● Gasoline is extremely flammable and explosive under certain conditions. Do not smoke around gasoline. Gasoline fumes are toxic when inhaled. Perform installation in a well ventilated area away from open flames or sparks. Any gasoline leak or spill constitutes a health and fire hazard. ● If motorcycle has been running, wait until engine and exhaust have cooled to avoid getting burned during installation. ● Electrical sparks can ignite explosive gasoline fumes. Failure to disconnect battery while working on motorcycle can also result in inadvertent engagement of starter and personal injury. A. Shut off fuel petcock and disconnect battery. B. Remove air cleaner assembly. Drain fuel from existing carburetor. Remove carburetor, manifold, choke cable and any carburetor mounting hardware NOTE – Removing and tightening hard to reach Allen bolts such as carb-manifold mounting bolts and V2 manifold flange bolts can be greatly simplified by the use of Allen ball-end drivers. These tools are available at most automotive and tool supply houses. See Picture 9. Additionally, Performance Plus of Evansville, Indiana, produces a hex wrench specially modified for accessibility of V 2 manifold bolts. Call 812-963-8854 for further information. As alternative, standard hex wrench can be shortened for convenience. NOTE – Some Buell motorcycles have a breather fitting with 90° elbow on rear head. Due to proximity of frame, elbow must be removed before fitting can be taken off engine. Loosen fitting and rotate to position convenient for cutting elbow. Secure fitting by tightening against cylinder head. Elbow may be inaccessible to hacksaw. In most instances, a die grinder with cutoff wheel will remove elbow with little difficulty. If die grinder is unavailable, grasp elbow firmly with pliers and snap off, then remove fitting. CAUTION – Extreme care must be taken to prevent metal chips from entering engine when elbow is removed. S&S recommends packing breather fitting with gease before removing elbow. Metal chips inside engine will cause extensive damage. Installer bears all responsibility for containment of chips and other debris. Picture 2 Picture 4 Picture 3
5 2. Prepare Air Cleaner Backplate NOTE – Fast idle lever screws, part #11-2384, must not be overtightened. Loctite or other thread locking compound may be used sparingly on threads to prevent screws from vibrating loose. CAUTION – Overtightening fast idle screws may damage backplate. A. All engines except V2s 1. Knuckles & Pans, 1936 to 1965 – Press plugs, part #50-8312, into holes in air cleaner backplate. See Picture 2 . 2. Shovels, 1966 to 1979, and Ironhead (IH) XLs, 1957 to 1979 – Press plug, part #50-8312, into hole in air cleaner backplate. See Picture 3 . 3. Shovels 1980 to 1984 and IH XLs 1980 to 1985 – Screw crankcase breather vent elbow fitting, part #50-8110, into hole in air cleaner backplate and angle downward as shown in Picture 4 . On 1983 and 1984 Shovels press plug, part #50-8312, into other hole on left. 4. Assemble fast idle mechanism as shown in Figure A . B. FL V2s 1984 to 1992 1. Press plug, part #50-8312, into hole on left in air cleaner backplate as shown in Picture 5 . 2. Screw vent hose elbow fitting, part #50-8110, into remaining hole at right. See Picture 5 . 3. Assemble fast idle mechanism as shown in Figure A . C. XL V2s 1986 to 1990 1. Press plug, part #50-8312, into hole on right in air cleaner backplate as shown in Picture 6 . 2. Screw vent hose nipple fitting, part #50-8111, into remaining hole at left. See Picture 6 . Elbow fitting, part #50-8110, supplied in kit may also be used in this location if required. 3. Assemble fast idle mechanism as shown in Figure A . D. FL V2s 1993 and up and XL V2s 1991 and up 1. Press plugs, part #50-8312, into both holes in air cleaner backplate as shown in Picture 7 . 2. Assemble fast idle mechanism as shown in Figure A . E. Buell motorcycles, 1994 and up 1. Assemble fast idle mechanism as shown in Figure A. 3. Throttle Preparation NOTE – Throttle grip assembly must be assembled correctly and work freely to prevent possible sticking during operation. Throttle must snap closed when released. Cable routing must be free of tight bends to minimize friction between cable and housing

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms: