c50c boulevard f1 code

You search Auto repair manual PDF c50c boulevard f1 code, if there are search results will appear below. If search results do not exist, please search by others keyword.



  c50c boulevard f1 code Direct Download speed 5282 Kb/s

  c50c boulevard f1 code Full Version speed 6162 Kb/s



Suzuki C50/ M50 Boulevard BIG AIR KIT INSTALLATION

0

Filed Under (Suzuki) by admin on 13-03-2012

download
1. Remove the (2) Bolts at the top of the stock air cleaner to the left and right of the oval rubber hose coming from under the fuel tank. 2. Loosen the hose clamp at the base of the oval rubber hose on the top of the air cleaner. 3. A male barb protrudes from the rear of the air cleaner that inserts into a rubber grommet mounted to the cylinders. Pull the air cleaner away from the cylinders firmly and you will feel the barb release. Now pull the upper section of the air cleaner downward to remove it from the oval snorkel tube from under the fuel tank. 4. Now you can reach to the rear of the box and unplug the electrical lead for the Air Sensor” which sits just about in the middle of the rear of the air cleaner. Now remove the breather hose at bottom of the air cleaner. 5. Set the air cleaner aside and turn it over to access the back. Remove the single bolt that secures the Air Sensor” (This sensor will be installed into the Aluminum Manifold of your new BAK assembly later) 6. Remove the lower mounting arm assembly from the cylinders. (You will not reuse this). 7. Using the (2) Dome head m6 x 15mm screws install the (2) #1 Arms to the rear (the side without the groove) of the backing plate, the shiny/chrome side of the arms should face outward. The smaller of the two holes in each arm is the one you place the screws through. Use the m6 Flange Nuts to secure the bolts at the rear of backing plate. Snug these up but do not tighten fully.

Incoming search terms:

SUZUKI BOULEVARD M109R Fuel Injected Models INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 16-02-2012

download
1. Remove seat, right and left side covers, and fuel tank. 2. Remove airbox. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness as shown in the picture. (Fig 1) 4. Unplug stock wiring harness from injectors and plug in the connectors from Fuelpak as shown. (Fig 2) 5. Unplug the TPS connector (grey) and attach T-tap connectors to the two outside wires. (Fig 3) 6. Route Fuelpak green wire to T-tap on the factory black wire with brown stripe. Routh the Fuelpak violet wire to T-tap on the factory pink wire with black stripe as shown (Fig 3) 7. Reattach the TPS connector. 8. Route red wire to the front of engine and down to the horn. (Fig 4) 9. Disconnect the two position connector from horn and snip connector in half so you have two one-wire connections. 10. Reattach factory grey wire to horn. Attach Fuelpak red wire to the other horn connection. Plug the factory horn orange wire to the male connection on the Fuelpak red wire. 11. Route black wire to battery negative connection as shown. (Fig 5) 12. Attach Fuelpak to Fuelpak harness and mount to bracket under the left side cover as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the red wire connection on the horn and that it is connected to the orange wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank.

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

2005 SUZUKI SV1000 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
TIRE PRESSURE FUEL + OIL COLD INFLATION TIRE PRESSURE FRONT REAR SOLO RIDING ITEM Fuel type kPa 250 250 DUAL RIDING kPa 250 290 NOTE E-03, 28, 33 The others E-33 The others Fuel tank Engine oil type Engine oil capacity SPECIFICATfON Use only unleaded gasoline of at least 87 pump octane (R12 + M12) or 91 octane or higher rated by the research method. Gasoline containing MTBE (Methyl Tertiary Butyl Ether), less than 10% etha- nol, or less than 5% methanol with appropriate cosolvents and corrosion inhibitor is permissible. Gasoline used should be graded 91 octane or higher. An unleaded gasoline is recommended. 16 L (4.2/3.5 USnrnp gal) 17 L (4.513.7 USIlmp gal) * SAE 10W-40, API SFlSG or SHISJ with JASO MA kgf/cm2 2.50 2.50 Change Filter change Overhaul psi 36 36 kgflcrn2 2.50 2.90 2 700 rnl (2.912.4 USllmp qi) 2 900 ml (3.112-6 US/lmp qt) 3 300 ml (3.U2.9 USllrnp qt) psi 36 42 CRANKCASE-CRANKSHAFT BEARING SELECTION Select the specrffed bearings from the crankcase bore I. D. code. The crankcase bore I.D. code (A) “A, “6″ or “C”, is stamped on the inside of each crankcase half. Bearing selection table Bearing thickness I.D. code @9 A B C Bearing must be replaced as a set. I.P. specification 52.000 – 52.006 mrn (2.0472 – 2.0475 in) 52.006 – 52.01 2 mm (2.0475 – 2.0477 in) 52.01 2 – 52,018 mm (2.0477 – 2.0479 in) Color (Part No.) Green (1 2229-1 6GOO-OAO) Black (1 2229- tGG00-OBO) Brown (I 2229- 16GOO-OCO) Color code 9 Bearing Green Black Brown Thickness 1.999 – 2.002 mrn (0.0787 – 0.0788 in) 2.002 – 2.005 mm (0.6788 – 0.0789 in) 2.005 – 2.008 rnm (0.0789 – 0.0791 in) FI SYSTEM WIRING DIAGRAM I ECM TERMINAL (For KCModel) ‘& ECM TERMINAL (For K5-Model) FAIL-SAFE FUNCTION & FI system is provided with fail-safe function ta allow the engine to start and the motorcycle to run in a mini- mum performance necessary even under malfunction condition

FLEXIBLE GAS PIPING DESIGN GUIDE and INSTALLATION INSTRUCTIONS

0

Filed Under (S&S) by admin on 29-10-2010

download
Definitions: Grounding : The process of making an electrical connection to the general mass of the earth. This is most often accomplished with ground rods, ground mats or some other grounding system. Low resistance grounding is critical to the operation of lightning protection techniques. Bonding : The process of making an electrical connection between the grounding electrode and any equipment, appliance, or metal conductor: pipes, plumbing, flues, etc. Equipment bonding serves to protect people and equipment in the event of an electrical fault. Equipotential Bonding : The process of making an electrical connection between the grounding electrode and any metal conductor: pipes, plumbing, flues, etc., which may be exposed to a lightning strike and can be a conductive path for lightning energy towards or away from the grounding electrode. 2. The National Fuel Gas Code NFPA 54/ANSI Z223 states, “Each above ground portion of a gas piping system upstream from the equipment shutoff valve shall be electrically continuous and bonded to any grounding electrode, as defined by NFPA 70, National Electrical Code ( ANSI/NFPA 70 1999 Edition.) 3. The TracPipe® gas piping system shall be bonded in accordance with the National Fuel Gas Code, NFPA 54/ANSI Z223. The piping system is not to be used as a grounding conductor or electrode for an electrical system. 4. For bonding of the TracPipe® system, a bonding clamp must be attached to the brass AutoFlare®fitting adapter (adjacent to the pipe thread area – see Figure 4-21) or to a black pipe component (pipe or fitting) located in the same electrically continuous gas piping system as the AutoFlare®fitting. The corrugated stain- less steel portion of the gas piping system SHALL NOT be used as the bonding attachment point under any circumstances. Bonding electrode conductor sizing shall be in accordance with Article 250 (Table 250-66) of ANSI/NFPA 70. The bonding is a requirement of the National Electrical Code

BMW 3 SERIES INSTALLATION MANUAL

0

Filed Under (BMW) by admin on 17-11-2010

download
1. Turn off the ignition and disconnect the negative battery cable. NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft code to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code. TO START: 2. Depress the wire-locking clip and disconnect the mass air sensor electrical. BMW 3 SERIES (E46) 1999-00 323i, ci 1999 323iC 2001-05* 325i, ci L6-2.5L 1999-00 328i 2000 328ci 2002-05 325xi L6-2.8L NOTE: * Excluding 2003 & 2005 PZEV model with engine family 3BMXV02.5M56 & 5BMXV02.5M56 Flat Blade Screwdriver Ratchet Extension 10mm Socket 10mm Wrench 4mm Allen A intake tube (EL) 1 087139 B hose ; 4mm id x 2″ l 1 08062 C npt fi tting; 1/4″ x 5/16″ barb 1 08908 D hose clamp #48 3 08601 E silicone hose 3.25″id x 2″l 1 08690 F nut; 6mm nylock 7 07553 G washer; 1/4″id x 5/8″od fl at 7 08275 H washer; 1/4″ split lock 1 08198 I bolt; 6mm-1.00 x 16mm, b/h/a 2 07730 J bolt; 6mm-1.00 x 12mm, b/h/a 4 07794 K washer; 1/4″id x 1″od fender 2 08160 L bracket 1 010087 M heat shield “A” 1 07492 N heat shield “C” 1 07497 O heat shield “B” 1 07494 P edge trim 46″L 1 102487 Q air fi lter 1 RU-4730 3. Pull up on the four fresh air duct-retaining pins to release them from the radiator core support. 4. Lift up and remove the fresh air duct from the vehicle as shown. NOTE: Disconnect the fresh air tube from the fresh air duct. 5. Loosen the hose clamp which secures the intake tube to the mass air sensor, and then disconnect the intake tube from the mass air sensor as shown. 6. Remove the two-factory air box mounting bolts shown.

TOYOTA/ LEXUS Transponder Bypass TYPE 1 & 2 INSTALLS

0

Filed Under (Toyota Manuals) by admin on 16-09-2011

Download
The 1100X/F-TL interface module is used when installing remote start
products in Toyota/Lexus vehicles equipped with a factory immobilizer.
The 1100X/F-TL allows for easy interfacing between the remote start and
the factory immobilizer, while maintaining the integrity of the OEM sys-
tem. The factory transponder-based anti-theft system uses a small elec-
tronic chip hidden in the key to send a code to the vehicle’s transceiver
when the ignition is energized. The key must be placed in the ignition
and turned to the RUN position. This energizes a coil surrounding the
key, which in turn energizes the chip, which sends a code to the vehicle. If
the vehicle does not detect the code being sent, the vehicle will start and
then immediately shut off or will just crank, and the anti-theft light will
flash. The 1100X/F-TL provides a valid code to the vehicle whenever it is
remote started, but does not affect the immobilizer system during normal
vehicle operation; the immobilizer system remains fully functional

Yamaha XV 1900A SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-8 3 NOTE: Make sure there are no other immobilizer keys close to the main switch, and do not keep more than one immobilizer key on the same key ring! Immobilizer system keys may cause signal interference, which may prevent the engine from starting. 2. If the engine starts, turn it off and try starting the engine with the standard keys. 3. If one or both of the standard keys do not start the engine, take the vehicle, the code re-registering key and both standard keys to a Yamaha dealer and have the standard keys re-registered. If the odometer/tripmeter/clock display indicates any error codes, note the code number, and then have a Yamaha dealer check the vehicle. CAUTION: ECA11590 If the display indicates an error code, the vehicle should be checked as soon as possible in order to avoid engine damage. Brightness control mode The brightness can be adjusted for the following: the multi-function meter unit panel (item number “1″) the LCD (item number “2″) the speedometer, tachometer, and the fuel gauge needles (item number “3″) Select the brightness control mode as follows. 1. Turn the key to “OFF”. 2. Push and hold the “SELECT” switch. 3. Turn the key to “ON”, and then release the “SELECT” switch after five seconds. Item number “1″ is displayed. 4. Adjust the multi-function meter unit panel brightness level by pushing the “RESET” switch. 5. Push the “SELECT” switch to select the LCD. Item number “2″ is displayed. Adjust the LCD brightness level by pushing the “RESET” switch. 1. Multi-function meter unit panel 2. LCD 3. Speedometer needle 4. Tachometer needle 5. Fuel gauge needle 1. Multi-function meter unit panel 2. Item number 3. Brightness level INSTRUMENT AND CONTROL FUNCTIONS 3-9 3 6. Push the “SELECT” switch to select the speedometer, tachometer, and the fuel gauge needles. Item number “3″ is displayed. Adjust the brightness level of the speedometer, tachometer, and the fuel gauge needles by pushing the “RESET” switch. 7. Push the “SELECT” switch. The odometer/tripmeter/clock display will return to the prior mode.

Aprilia RSV4 Factory TITANIUM RACING EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Aprilia) by admin on 26-10-2010

download
Made in polished carbon fiber, and fit onto the original footrests giving a better look and a weight reduction. They can also be fitted to the adjustable footrests. Code: 895318 CARboN FIbER HEAT pRoTECTIoN Made in polished carbon fiber with an inner thermal insulation layer. It fits to the original muffler giving a sporty look and weight reduction. Code: 895319 SERvICE STAND Constructed from high grade, powder coated steel, and fitted with nylon wheels with bearings. Side plate sporting laser cut RSV4 logo. Code: 894870 REAR STAND pICk Up kNobS Made from CNC machined billet aluminium by DPM race in collaboration with Aprilia, ensure maximum stability of your RSV4 while on a rear stand with these secure pick up knobs

BMW Motorcycle F 650 GS/ F 800 GS Accessories

0

Filed Under (BMW) by admin on 20-11-2010

download
Stowage-equipment line Vario case, black, left 71 60 7 696 299 £184 / G Vario case, black, right 71 60 7 696 300 £185 / G (+) Case carrier for Vario case, including fasteners 71 60 7 696 301 £144 / G (+) Lock barrel, complete, for 2 cases 51 25 7 688 566 £20.80 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 2x) 51 25 7 681 199 £33.59 (o) Lock-barrel set 51 25 7 698 202 £15.20 / I Liner for Vario case, left 71 60 7 687 610 £67 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Vario topcase, black 71 60 7 696 302 £225 / I (+) Luggage rack, large, for Vario topcase (including adapter plate) 71 60 7 696 303 £64 / I (+) Lock barrel for topcase 51 25 7 688 568 £12.50 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 1x) 51 25 7 681 199 £33.60 / I (o) Lock barrels for 2 cases and topcase 51 25 7 688 567 £29.10 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Backrest pad for topcase 71 60 7 688 877 £45 / I Luggage carrier, small 71 60 7 701 810 £42.90 / G Tank rucksack, waterproof 71 60 7 711 240 £130 / I Enduro rear softbag 71 60 7 711 245 £35.90 / I Sport softbag, small, 19 l 71 60 7 694 117 £102 / I Sport softbag, large, 51 l 71 60 7 693 567 £139 / I Stuffbag, waterproof, 53 l 72 60 7 653 818 £90 / I Luggage strap with pull-tight buckle 72 60 2 304 808 £6.30 / E Bungee-cord spider 72 60 9 057 579 £3.95 / E Design line Spray-guard extension, rear 71 60 7 695 031 £24.20 / I Sound components Akrapović sports silencer 71 60 7 713 339 *1 £475 / G Ergonomics and comfort line Windscreen, large, tinted 71 60 7 713 834 *1 £138 / I Windscreen, large, clear (standard for F 800 GS) 71 60 7 713 833 £127 / I Windscreen, small, clear (standard for F 650 GS) 71 60 7 713 296 £87 / I Centre stand (F 650 GS) 46 52 7 700 864 *2 £83 / I Centre stand (F 800 GS) 46 52 7 700 049 *2 £91.50 / I (+) Fasteners for centre stand (F 650 GS + F 800 GS) 71 60 7 706 738 £24.90 / I Seat, low, black, 790 mm (F 650 GS), 850 mm ( F 800 GS) 52 53 7 695 013 £174 / I Heated handlebar grips and switches (see electronic parts catalogue) Navigation and communication components BMW Motorrad Navigator III plus 2008 72 60 7 716 116 *1 £650 / I (+) Holder for BMW Motorrad Navigator 71 60 7 697 785 £45.80 / E (+) Securing screw (order 4 of) 32 71 7 652 161 £4.55 / I Connecting cable for BMW Motorrad Navigator 71 60 7 686 670 £55 / E TMC module for BMW Motorrad Navigator 72 60 7 702 687 *1/3 £111 / E Car kit for BMW Motorrad Navigator 72 60 7 703 996 *3 £60.50 / E Navigator carry-bag function 71 60 7 683 161 £49 / I Safety line Hand-protector bar 71 60 7 716 043 £57 / I (+) Countersunk-head screw (order 2 of) 32 71 7 712 836 £3.34 / E Hand protector, small 71 60 7 705 963 £19.50 / I Hand protector, large 71 60 7 715 135 £23.10 / I Protector-mounted spoiler for hand protector, large 71 60 7 705 964 £15.20 / I Crash bar, left 71 60 7 699 437 £104 / I Crash bar, right 71 60 7 699 438 £104 / I (+) Fasteners for crash bar 71 60 7 702 395

Incoming search terms: