carb heater zr7s

You search Auto repair manual PDF carb heater zr7s, if there are search results will appear below. If search results do not exist, please search by others keyword.



  carb heater zr7s Direct Download speed 5282 Kb/s

  carb heater zr7s Full Version speed 6162 Kb/s



KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Motorcycle Hand Warmer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Disconnect the Positive (+) terminal from the battery. 2. Remove the existing grip from the Clutch side. Removing the grip may require blowing compressed air in the end between the grip and the bar, injecting brake cleaner fluid, or cutting it off. 3. Clean the handlebar where the grip was removed with alcohol or a solvent to remove all residue and dry with a clean cloth. 4. Determine where the Clutch side heater will be mounted. Take the heater marked “Clutch” and place it on the handlebar approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 9:00 o’clock or they can be positioned on the bottom for appearance. Peel off the release paper and adhere the heater to the handlebar with the wires toward the headlight. 5. Apply a high temperature adhesive (such as JB Weld) to the inside of the Clutch side grip. Install the grips over the heaters and let the adhesive cure as instructed by the adhesive manufacturer. 6. The Throttle side heater is installed on the throttle sleeve under the rubber cover. Remove the rubber cover that is installed over the throttle sleeve so the Throttle side heater can be applied. Some of the throttle sleeves have ribs which need to be cut or ground off so the heater can make full contact with the sleeve surface or it will over heat in the void areas. 7. Determine where the throttle side heater will be mounted. Take the heater marked “Throttle” and place it on the throttle sleeve approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 3:00 o’clock with a loop to allow for the twisting motion of the throttle. Peel off the release paper and adhere the heater to the throttle sleeve with the wires toward the headlight. 8. Apply a thin coat of adhesive (such as J.B. Weld) to the surface of heater only and reroll the rubber hand grip over the entire throttle sleeve. Wipe off any excessive adhesive that may have rolled out

42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.

Cobra Motorcycle and ATV Specifications CX65 CX50 Sr. (The King) CX50 Jr. ECX 70 ECX 50 ECX80AC

0

Filed Under (Cobra) by admin on 14-11-2010

download
Dry Weight 122 lbs 91 lbs 81 lbs 210 lbs 206 lbs 210 lbs Engine Cobra 65cc 2-stroke Cobra 50cc 2-stroke Cobra 50cc 2-stroke Cobra 70cc 2-stroke Cobra 50cc 2-stroke Cobra 80cc 2-stroke Bore x Stroke 44.5mm x 41.7mm 39mm x 41.7mm 39mm x 41.7mm 44.5mm x 44.7mm 39mm x 41.7mm 47.6 mm x 44.7mm Induction Case Reed V-Force® Reed Valve- 24mm Mikuni carb Case Reed Carbon Pedal 19mm carb Case Reed Carbon Pedal 14mm carb Case Reed V-Force® Reed Valve- 24mm Mikuni carb Case Reed Carbon Pedal 21mm carb Case Reed V-Force® Reed Valve- 24mm Mikuni carb Cooling Water cooled Cylinder and Case Water cooled Water cooled Water cooled Cylinder and Case Water cooled Water cooled Cylinder and Case Clutch Hydraulic ally actuated Cobra 3Gx 3-Shoe Cobra 3Gx 3-Shoe Hydraulic ally actuated – (auto option) Cobra 3Gx 3-Shoe Rekluse Z-ball auto-clutch Transmission Six-speed sequential Single-speed auto Single-speed auto Six-speed sequential Single-speed auto Six-speed sequential Exhaust Tuned pipe and silencer Tuned pipe and silencer Tuned pipe and silencer Tuned pipe and silencer Tuned pipe and silencer Tuned pipe and silencer Lubrication Mixture lubrication Mixture lubrication Mixture lubrication Mixture lubrication Mixture lubrication Mixture lubrication Fuel Capacity 1.06 Gallons .85 Gallons .70 Gallons 1.9 Gallons 1.9 Gallons 1.9 Gallons Frame Twin Spar Oval HSLA Double Cradle 4130 ChrMo Steel Double Cradle 4130 ChrMo Steel Arens design twin spar Arens design twin spar Arens design twin spar Wheelbase 1140mm 990 mm 908 mm 1067mm (track 915mm) 1067mm (track 915mm) 1067mm (track 915mm) Seat Height 762mm 680 mm 607 mm 762 mm 737 mm 762mm Ground Clearance 250mm 240 mm 216 mm 205 mm 205 mm 205mm Front Brakes Hydraulic Disk (205mm) Hydraulic Disk (160mm) Hydraulic Disk (160mm) Hydraulic Disk (160mm) Hydraulic Disk (160mm) Hydraulic Disk (160mm) Rear Brakes Hydraulic Disk (165mm) Hydraulic Disk (140mm) Adjustable Drum Hydraulic Disk (180mm) Hydraulic Disk (180mm) Hydraulic Disk (180mm) Front Suspension Marzocchi 35mm USD Adjustable 220mm travel Cobra 30mm USD 210mm travel Marzocchi 32mm 168mm travel Dual A-Arm with SVO™ patented steering design. 248mm travel Dual A-Arm with SVO™ patented steering design. 248mm travel Dual A-Arm with SVO™ patented steering design. 248mm travel Rear Suspension Öhlins Fully Adjustable 270mm travel Fox Piggyback Fully Adjustable 248mm travel Öhlins Piggyback 170mm travel Fox Piggyback 220mm travel Solid axle Fox Piggyback 220mm travel Lightweight tube axle Fox Piggyback 220mm travel Solid axle Wheel Front / Rear 14″ spoke / 12″ spoke (Al rims, Billet hubs, 9ga. spokes) Cobra 12″ Billet Cobra 10″ Billet Cobra 10″ Billet Cobra 10″ Billet ITP 10×5 (4 x1) Al Douglas 8×6.5 (4×2.5) Al ITP 10×5 (4 x1) Al Douglas 8×6.5 (4×2.5) Al ITP 10×5 (4 x1) Al Douglas 8×6.5 (4×2.5) Al Tires Front / Rear 60-100×14 Dunlop 80-100×12 Dunlop 2.5×12 / 2.75×10 2.5×10 / 2.75×10 ITP Holeshot 19/6 ITP 16/6.50-9 ITP Holeshot 19/6 ITP 16/6.50-9 ITP Holeshot 19/6 ITP 16/6.50-9

Incoming search terms:

2003 – 2005 Corolla HEATER PERFORMANCE IMPROVEMENT REPAIR

0

Filed Under (Toyota Manuals) by admin on 30-10-2011

download
Install the SST to the piping clamp. SST: 09870-00015 HINT: Confirm the direction of the piping clamp claw and the SST using the illustration shown on the caution label. B. Push down the SST and release the clamp lock. NOTE: Be careful not to deform the tube when pushing the SST. C. Pull the SST slightly and push the release lever. Then remove the piping clamp with the SST. D. Remove the piping clamp from the SST. E. Disconnect the cooler refrigerant suction hose No. 1. NOTE: Disconnect the tube by hand only. Do not pry the tube apart. Cap the open fittings immediately to keep moisture or dirt out of the system

HONDA TRX 400EX Removing Stock Carb and Cables INSTRUCTION

0

Filed Under (Honda) by admin on 21-12-2011

download
Remove seat/fender assembly and fuel tank. 2. Remove throttle cables paying close attention to routing. 3. Remove thumb throttle housing if you are installing a twist throttle. 4. Remove air box and air box intake tube. 5. Remove stock carburetor. 6. Stuff a clean rag into intake manifold to keep debris from entering engine. Preparing machine for carburetor installation 1 . Route the provided throttle cables per manufacturer’s recommended procedure, routing them the same as the stock cables. 2 . Remove the rubber alignment tabs from the manifold using a razor blade or cutters. Be very careful not to damage the intake manifold! 3. Remove air box intake tube from the air box and use a hacksaw to cut approx. 1½” off of the air box intake tube. Your tube should resemble the one shown in Figure 1. Re-assemble the air intake tube into air box and install back onto bike. Don’t forget to tighten clamp around intake tube and reinsert crank vent into the air boot. Figure 1. Thumb Throttle Attach cable into cable wheel with the cable end at the 8: 00 position of the cable wheel, then into bracket. Secure by replacing the cable bracket end and phillips screw. See Figure 2. Figure 2. Twist Throttle 1. Install the pull (see figure 4 for cable identification) , cable end into the 8: 00 position and the idle cable end into the 11: 00 position on the cable wheel. See Figure 3

THUNDERJET INSTALLATION FIXTURE for S&S CARBURETORS

0

Filed Under (S&S) by admin on 31-10-2010

download
FUEL DELIVERY TUBE 6 5 6 5 6 5 6 5 -A Ambe -A Ambe r rton Drive, Elkridg e, MD 21075 410-579-2828 e, MD 21075 410-579-2828 ton Drive, Elkridg Using the two ¼”- 20 cap screws provided, secure t carb body at air cleaner surface to fixture through h # 2 & 5 . NOTE: Holes # 2 & 6 may be used to angle th ThunderJe clearance is needed below the fuel tank. he oles e t farther forward if additional ADJUSTABLE AIR BLEED les # RIGINAL AIR Secure Carb to fixture using ho & 8. 1 O LEED B BLOCKING Secure C fixture using ho & 6. arb to les # 1 BOWL VENT RELOCATION Secure Carb to fixture using holes # 6 & 7 . FLOAT BOWL ee Reverse side for S&S ‘B’ & ‘D’ Secure float bowl to fixture using the 3/8″- 16 flange nut and threaded rod provided using the 20 degree slope. S instructions. S&S ‘B’ & ‘D’ CARBS EXTERNAL BOWL VENT 6 5 6 5 6 5 6 5 -A Amberton Drive, Elkridge, MD 21075 410-579-2828 -A Amberton Drive, Elkridge, MD 21075 410-579-2828  ADJUSTABLE AIR BLEED THUNDERJET FUEL TUBE :00 position, viewed facing air filter (9 surface) sing the two #10-24 cap screws provided, :00 position, viewed facing air filter U secure the Carb body at bowl surface to fixture through the two holes marked ‘B’ . (3 surface) Using the two #10-24 cap screws provided, FLOAT BOWL secure the Carb body at bowl surface to fixture through the two holes marked ‘D

Kawasaki Mule Lift Kit Installation Manual

0

Filed Under (Kawasaki) by admin on 04-05-2012

download
Front Lift Installation 1. Ensuring that the parking brake is set, place jack under center of the Mule front end and lift until front wheels clear the ground. Be careful to support Mule properly so that it is secure, but so that the A-arms and struts can droop to full extension. 2. Remove front wheels. 3. If applicable, remove the heater to allow access to the strut mount behind the heater coil. Heater 4. Starting with the left side (driver side), remove the cotter pin and castle nut that secures the strut to the strut mount. Castle Nut & Pen 5. Push bolt through the bolthole, taking care not to damage the brake line that is attached to the bolt. If you are having difficulty removing the bolt, you may have to remove the brake lines that are attached to the front brakes. In this case refer to owners manual for removing brake lines. Screwdriver NOTE: Keep in mind that if you remove the brake lines you must bleed your brakes according to operator’s manual. 6. Once the bottom of the strut has been loosened, then unbolt the top of the strut. The nuts securing the top strut can be located in the dash of the Mule on the left and right sides. In most cases these nuts are easily accessible, but you may have to remove the glove box or heater coils, depending on the model and options purchased with the Mule.

Incoming search terms:

Incoming search terms: