carb sinc suzuki intruder

You search Auto repair manual PDF carb sinc suzuki intruder, if there are search results will appear below. If search results do not exist, please search by others keyword.



  carb sinc suzuki intruder Direct Download speed 5282 Kb/s

  carb sinc suzuki intruder Full Version speed 6162 Kb/s



KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Incoming search terms:

42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

SUZUKI 1400/ 800 INTRUDER TURN SIGNAL RELOCATION INSTALLATION AND CLEANING INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 09-11-2010

download
1. Refer to Figure 1. 2. Remove seat. Safety: disconnect battery prior to all wiring modifications LeatherLyke 510 5/1/2009 3. Disconnect wires to turn signals. 4. Remove turn signals and retain hardware for reinstallation. Observe and mark “left” and “right” for reinstallation. Information: Do not remove license plate bracket . 5. Remove license plate. Turn signal bracket must be oriented with flange (side with only 2 holes) on top. 6. Install turn signal bracket behind license plate bracket and license plate using 6 x 35mm pan phil machine screws for the 800 or 6 x 20mm pan phil machine screws for the 1400, 1/4″ flat washers, and 6mm locknuts. Insert black spacer spool between license plate bracket and turn signal bracket. 7. Mount turn signals directly to turn signal bracket using 6 x 10mm hex cap screws and star lock washer. Information: Observe all color-coding of wires and splice one wire at a time. 8. Cut each turn signal wires three inches from end and splice 10 inches of supplied wire. Secure wires to inner fender clips. 9. Follow route of tail light wires and connect wires into harness. 10. Secure wires together behind license plate bracket with tie wrap. 11. Connect battery and test turn signals for function. 12. Install seat. Information: Not all license plate mounts are grounded. In some cases, it may be necessary to run a ground wire to turn signal bracket. WARNING: States may have minimum width requirements on motorcycle turn- signals, so check your local laws. LeatherLyke 510 5/1/2009 SADDLEBAG INSTALLATION 13. Refer to Figure 2. Information: Cover plates are pressed into strut. 14. Remove round cover plate at end of fender mount strut on right side. 15. Remove nut on right rear and replace with 1.2″ hex adapter. If hex adapter is less than flush with the outside of both fender struts, add a 5/16″ flat washer. 16. Assemble 5 x 30mm flathead screw and 5mm mounting spool with chamfer on spool under head of screw. Insert assembly thru 1 1/4″ fender washer for the 1400 or 1″ for the 800. 17. Install spool assembly into previously installed 1.2” hex adapter. Information: Do not remove washer on shock absorber. Hex adapter will protrude 1/4″ beyond fender strut. 18. Remove round cover plate over right rear shock, remove shock absorber nut and install .75″ hex adapter. 19. Assemble 5 x 30mm flathead screw, mounting spool and cup washer with chamfer on spool under head of screw. 20. Install spool assembly into previously installed hex adapter. 21. Insert 5/8” finishing plug into old turn signal hole on right side. 22. Repeat procedures on opposite side

Incoming search terms:

SUZUKI INTRUDER 1500 LC BOTH WHEELS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 27-02-2011

download
In order to keep the proper balance on the bike lift, I would suggest that the front wheel be removed first, this is comparatively easier than the rear wheel which will be explained later. Front wheel removal : Remove the end caps, remove the front axle “Pinch Bolt” front left fork ( item (2) in manual ) remove caliper bolts both (2) both sides (2003 model year) secure calipers, secure wheel from dropping while removing axle from left side. Remove front axle, caution : there are (2) spacers on this axle, left & right, make sure you mark them, as they are both different in shape & in length, & must be re-assembled in same order to provide proper cetrallity of the front wheel with the forks & the brake calipers.both spacers have large flanges which go towards the bearing, the right spacer has (2) flanges, the largest dia. goes towards the bearing. ( very important) Now comes the tough part, I had the original stock pipes, so if you have different pipes, or your bike is a different year, (2003) your choices may be different from mine. Remove OEM right side saddlebag, slack off muffler coupling brackets # 8 & # 8a which connect muffler crossover tank to top muffler, this is where the power of the allen socket wrench set will come in handy, they’re pretty tight with the heat,remove top exhaust pipe bracket bolt (item 19 in manual) the top exhaust pipe should now swing down clear of the rear axle. You may be forced to provide more room for the exit and/or re-installation of the rear wheel by removing the bolt which secures the underside mufflet tank on the lower left side of the frame, (item # 13 in manual) then the (2) bolts, ( items # 14 in manual) which will allow the rear muffler body ( lower exhaust pipe ) to be pulled over to the right to provide access for easier rear wheel entry or removal

Incoming search terms:

Suzuki INTRUDER 1400 SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Suzuki) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosenthe mounting bolt and pinch clamp on both left and right hand mufflers. 2. Loosenthe clamp on the crossover tube, located between the two mufflers. 3. Remove the two nuts that mount the front head pipe flange to the cylinder head. 4. Remove the two nuts that mount the rear head pipe flange to the cylinder head. 5. Remove the head pipes using a twisting motion to break the seal at the muffler and to clear the cylinder head. Note : If the exhaust coupler gaskets did not remain in the mufflers, remove them from the head pipes at this time. These coupler gaskets will not be reused in your new exhaust system. 6. Remove the mounting bolt from the left hand muffler. Remove the muffler, again using a twisting motion to seperate the crossover tube and set the muffler aside. (Save the stock mounting hardware for reuse). 7. Repeat step #6 on the the right hand muffler. Set the muffler aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Reinstall the stock head pipes to the engine. Note : Leave the flange nuts loose at this time. 3. Remove the mufflers from their boxes. There are a left and right hand muffler in this system. To define the difference between the left and right mufflers, check the bracket that is welded to the back side of the muffler. Each muffler is stamped with it’s own part number. Part # D500 is the RIGHT muffler and Part # D550 is the LEFTmuffler. 4. Install a three hole mounting bracket to each of the mufflers. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16 flange head bolts (supplied), leave them loose at this time. Note : Each muffler bracket has a number stamped on it, #179 bracket is for the left hand muffler and #180 is for the right hand muffler. When the brackets are mounted correctly, the end of the bracket with the single hole should point to the inlet end (small end) of the muffler. Refer to figure 1.

Incoming search terms:

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms:

SUZUKI PUTS THE 'STYLE' IN LIFESTYLE WITH CUSTOM ACCESSORIES INSTALLATION

0

Filed Under (Suzuki) by admin on 14-02-2012

download
Suzuki Genuine Accessories are available for the all-new Equator midsize pickup truck, four-door SX4 Sport, five-door SX4 Crossover, XL7 midsize crossover and rugged Grand Vitara. The accessories can be purchased through local Suzuki dealers. Suzuki Equator  All-weather floor mats – Rubberized all-weather mats, ideal for keeping dirt, moisture and harsh debris from coming in contact with the vehicle’s carpet interior.  Bluetooth® module – The Suzuki-integrated hands-free Bluetooth phone system features a clean installation, fresh look and works with most Bluetooth-enabled mobile phones. Quality sound plays through the vehicle’s factory stereo and speakers, and the phone system automatically mutes the radio during phone calls. (Also available for SX4 Sport, SX4 Crossover, Grand Vitara and XL7.)  Body side moldings – Durable polyurethane molding set helps protect exterior paint from door dings and road rash.  Hood mask – Durable vinyl, custom-fit mask helps protect the front end of the vehicle from damage caused by minor road debris.  iPod® interface kit – Provides a seamless connection from an iPod to the vehicle’s radio and/or steering-wheel audio controls. (Also available for SX4 Sport, SX4 Crossover, Grand Vitara and XL7.)

Incoming search terms:

SUZUKI MOTORCYCLES Gsxr 600, Gsxr 750, Gsxr 1000 teak the lead

0

Filed Under (Suzuki) by admin on 12-11-2010

download
The launch of the sixth generation of Gsxr marked a shift in Suzuki’s emphasis on two fronts. One, the Gsxr 1000 now took the upper hand in the development stakes. Historically, the Gsxr 750 led the march-arriving first, gaining the most recent technology, absorbing the lion’s share of corporate pride-but by 2003 the Gsxr 1000 was in the lead. Two, the Gsxr 1000 represents another, more subtle shift for Suzuki engineering, in which the designers-the lucky guys who get to clothe these amazing machines-have more freedom of expression. With this generation, the designs turned edgier, sharper, more aggressive looking than ever. What’s more, the Gsxr 1000 K3 would be the proving ground for a host of changes brought to the Gsxr 600 and Gsxr 750 for 2004. In fact, nearly every upgrade to the smaller bikes appeared on the Gsxr 1000 a year before. But the real impetus for driving the Gsxr 1000 to the head of development and, indeed, shortening its development cycle was competition both on the track and in the showroom. For the track, it was understood that Superbike racing would revert to allowing 1000 cc four-cylinder bikes in place of the 750s that had been the limit since 1982. In 2002, Yoshimura and Mat Mladin barely lost the AMA Superbike crown to Nicky Hayden aboard the Honda RC5!. But it would be the RC’s swan song of competitiveness with the change to 1000 cc fours. To keep speeds in check, the AMA Superbike rules would require 1000 cc fours to have some additional limitations compared to the twins and triples. For example, “Cylinder heads may be ported and machined, but altering of valve angles will not be permitted; aftermarket valves, springs, retainers, and other valve-train components will be permitted; valves must be stock size and same basic material as original equipment; aftermarket camshafts will be permitted, but earn lift and resulting valve lift must be no greater than stock. “In addition, the “stock crankshaft must be retained, The only allowable modifications are balancing, polishing of bearing surfaces and attachment of accessory drives. Homologated transmission gear sets (one optional set of ratios per approved model) will be permitted. Optional sets will be price-controlled and must be available to any legitimate AMA Superbike competitor. Homologated fuel-injection throttle-body assemblies (one optional type per approved model) and aftermarket airboxes will be permitted. Modifications to throttle bodies will not be permitted. Optional throttle bodies will be price-controlled and must be available to any legitimate AMA Superbike competitor.” The thinking was simple: keep the liter bikes from sucking through massive throttle bodies, and the horsepower might not (and, it was hoped, would not) go through the roof. In preparation for racing, Suzuki moto wanted to make a host of small changes to the Gsxr 1000, but its motivation was also to keep the bike at the forefront of open-class street bikes. Suzuki engineers knew that Honda and Kawasaki were readying all-new models-the CBR 954 RR and the ZX 9 R had long since been vanquished-and rumor had it that Yamaha was ready with yet another push with the R1.It was the right time to make alterations to the Gsxr 1000. Heading the list was, as one might expect, a revised engine.

Incoming search terms:

Incoming search terms: