cbr 600 f4i ecu

You search Auto repair manual PDF cbr 600 f4i ecu, if there are search results will appear below. If search results do not exist, please search by others keyword.



  cbr 600 f4i ecu Direct Download speed 5282 Kb/s

  cbr 600 f4i ecu Full Version speed 6162 Kb/s



Honda CBR F4 or F4I 600cc Engine PE-ECU-1 System INSTALLATION

0

Filed Under (Honda) by admin on 05-01-2012

download
The PE-ECU-1 can be installed on virtually any 1,2,4,6 or 8 cylinder even-firing engine that requires fuel injection and/or ignition control. All of the functions of the ECU can be adjusted by using a laptop or PC running Windows. The following describes the basic requirements for using the system with a Honda 600cc F4 or F4I motorcycle engine. Please refer to the User’s Manual for a more in-depth description. Input Sensors The stock Honda F4 and F4I crank position sensors can be used with the PE-ECU-1 engine control system, provided the engine controller is configured for a 2- wire variable reluctance sensor. The configuration for the input is handled at the factory via a set of board jumpers. If the type of crank sensor should ever be changed, please contact PE for support on this issue. The stock Honda crank sensor should be wired according to the following: • Solid Yellow Wire – Pin 34 on ECU • Yellow with White Stripe (GND) – Pin 25 on ECU Failure to wire the sensor in this way may result in an engine that misfires and/or has incorrect ignition timing. The stock Honda trigger wheel cannot be used with the PE-ECU-1 system due to the differences in the number and spacing of the teeth. The PE-ECU-1 must be provided with a 12-1 pulse-train, correctly phased with TDC #1 according to Figure 1

Incoming search terms:

Honda CBR 600 F4i 2004 – 2005 Bestem USA Fiberglass F13 Installation Guide

0

Filed Under (Honda) by admin on 20-11-2011

download
We highly recommend having a professional install this undertail. A dremel tool or nsimilar is what we found the best to cut plastics. Place bike on a rear wheel center stand. Remove passenger seat and hardware which secure stock undertail section Unplug the harness that connects tail light and remove the stock undertail. Position Bestem undertail close to the bike and determine the amount of plastic needs to be cut out. Use a dremel tool to carefully trim off plastics (glove boxes etc). This is the most time consuming part of the installation but your patience will be paid off. 5) Once the new undertail is slide in, determine holes need to be drilled (only on
certain models). Reuse the hardware for the stock undertail to secure the new undertail. 6) The wiring color codes from two round tail lights are Black Wire – Ground, connects to Ground wire. Red Wire – Brake Light, connects to brake light. Blue Wire – Running Light, connect directly to the running light. Orange Wire – Turn Signal, connect them to your L/R turn signal wires We highly suggest you solder the connections and use heat shrink wrap to seal the connections. Test your lights before going out for a ride, also make sure your new undertail is securely installed on the bike. Now it’s time to go out for a spin!

Incoming search terms:

Honda CBR-600 F4 / F4i – Installation Instructions (slip-on)

0

Filed Under (Honda) by admin on 11-11-2011

download
Remove the lower fairing. Remove the existing exhaust system from the middle of the stock pipe. Save the stock exhaust can mounting bolt and nut for the end can to the passenger footpeg for reuse as well. Remove the clamp from the stock exhaust system and save for reuse. Install the S-Bend to the rear of the stock head pipe. Reuse the stock clamp, but do not tighten at this time. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1 for details. Place the bands approximately 190-200mm from the edge of the end can. See figure 2 for details.
Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount
the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G.
Attach the supplied springs to fasten the end can to the S-bend pipe. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. Carefully align the two stainless bands K so that they are parallel to each other, and spaced prope rly on the can (refer to step 7 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

Harley-Davidson Camshaft TC, EVO, Shovelhead, XL EVO, Iron Head, XR Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
EVO Black Widow PP8833-2 – 29 55 62 25 264 267 54 103 109 105.8 0.600 0.602 EVO Black Widow PP8826-2 – 27 61 63 29 268 272 56 107 107 107.0 0.602 0.602 EVO Black Widow PP8817-2 – 254 254 0.590 0.590 EVO Carl’s Speed Shop CM4 – 28 44 52 20 252 252 48 98 106 102.0 0.495 0.495 EVO Carl’s Speed Shop CM495F Y 19 47 50 16 246 246 35 104 107 105.5 0.495 0.495 0.179 0.168 EVO Carl’s Speed Shop CM580 – 19 47 50 16 246 246 35 104 107 105.5 0.580 0.580 0.194 0.163 EVO Carl’s Speed Shop CM612 – 36 60 68 28 276 276 64 102 110 106.0 0.612 0.612 0.277 0.235 88 EVO Carl’s Speed Shop CM660 – 38 62 68 28 280 276 66 102 110 106.0 0.660 0.660 0.314 0.277 90 EVO Carl’s Speed Shop CM774 – 284 284 0.784 0.784 0.277 0.236 EVO Carl’s Speed Shop CM780F – 34 70 74 30 284 284 64 108 112 110.0 0.774 0.774 103 EVO Crane EVR0020 – 31 64.5 77 23 275 280 54 107 117 112.0 0.608 0.589 88 EVO Crane Fireball 2000 Y -12 22 20 -10 190 190 -22 107 105 106.0 0.490 0.490 0.026 0.032 EVO Crane Fireball 300 Y 12 34 41 15 226 236 27 101 103 102.0 0.490 0.490 4000 EVO Crane Fireball 310 Y 16 40 43 19 236 242 35 102 102 102.0 0.490 0.490 1500 4500 75 EVO Crane Fireball 316 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 2000 5000 80 EVO Crane Fireball 326 – 24 48 57 25 252 262 49 102 106 104.0 0.490 0.500 2500 5500 EVO Crane H286 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 2000 5000 80 EVO Crane H290 – 17 43 45 23 240 248 40 103 101 102.0 0.581 0.581 1800 5200 EVO Crane H296 – 24 48 57 25 252 262 49 102 106 104.0 0.490 0.500 2500 5500 EVO Crane H304 – 24 50 55 25 254 260 49 103 105 104.0 0.600 0.600 2500 5800 EVO Crane H306 – 28 54 69 23 262 272 51 103 113 108.0 0.500 0.510 0.224 0.195 3000 6000 EVO Crane H310 – 23 63 68 28 266 276 51 110 110 110.0 0.550 0.550 0.229 0.229 3000 6500 88 EVO Crane H314 – 26 54 65 21 260 266 47 104 112 108.0 0.600 0.600 2800 6000 EVO Crane HEV0042 – 27 59 71 23 266 274 50 106 114 110.0 0.600 0.576 0.226 0.194 3000 6000 100 116 EVO Crane HEV0067 – 24 50 56 24 254 260 48 103 106 104.5 0.600 0.530 0.128 0.113 EVO Crane HEV0098 – 36 62 72 34 278 286 70 103 109 106.0 0.650 0.650 0.171 0.156 96 EVO CycleRama CR-E550 – 24 52 53 23 256 256 47 104 105 104.5 0.550 0.530 EVO CycleRama CR-E581 – 22 46 53 23 248 256 45 102 105 103.5 0.581 0.550 EVO CycleRama CR-E600A – 24 50 56 24 254 260 48 103 106 104.5 0.600 0.530 EVO CycleRama CR-E600B – 23 51 54 22 254 256 45 104 106 105.0 0.600 0.550 EVO CycleRama CR-E617 – 22 50 50 22 252 252 44 104 104 104.0 0.617 0.617 EVO CycleRama CR-E630 – 18 60 63 13 258 256 31 111 115 113.0 0.630 0.630 EVO CycleRama CR-E660 – 27 59 71 23 266 274 50 106 114 110.0 0.660 0.660 3500 6500 140 EVO Dave Mackie DM500 Y 22 38 52 12 240 244 34 98 110 104.0 0.500 0.500 0.189 0.138 EVO Dave Mackie DM500X Y 25 40 55 20 245 255 45 98 108 102.5 0.500 0.500 0.208 0.178 EVO Dave Mackie DM530 – 28 42 55 15 250 250 43 97 110 103.5 0.530 0.530 0.221 0.141 EVO Dave Mackie DM580 – 26 42 56 12 248 248 38 98 112 105.0 0.580 0.580 0.227 0.144 113 EVO Dave Mackie DM581 – 26 42 56 12 248 248 38 98 112 105.0 0.580 0.580 0.227 0.144 EVO Dave Mackie DM595 – 21 49 57 14 250 251 35 104 112 107.8 0.595 0.595 0.192 0.150 EVO Dave Mackie DM635 – 20 56 59 18 256 257 38 108 111 109.3 0.635 0.635 0.194 0.176 EVO Edlebrock 1740 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 0.176 0.203 EVO Edlebrock 1741 – 20 46 52 22 246 254 42 103 105 104.0 0.600 0.600 0.183 0.187 EVO Head Quarters HQ-23 – 19 47 52 24 246 256 43 104 104 104.0 0.600 0.530 EVO Head Quarters HQ-24 Y 20 36 52 19 236 251 39 98 107 102.3 0.500 0.500 EVO Head Quarters HQ-25 – 18 38 42 14 236 236 32 100 104 102.0 0.550 0.550 EVO Head Quarters HQ-26 – 20 54 53 22 254 255 42 107 106 106.3 0.600 0.530 89 EVO Head Quarters HQ-27 – 26 60 70 24 266 274 50 107 113 110.0 0.650 0.575

Incoming search terms:

2001 – 2003 Prius 2003 4Runner, Camry, Land Cruiser and Sequoia VEHICLES EQUIPPED WITH TRANSPONDER ECU

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
When replacing the ECM (SAE term: PCM) or the Transponder ECU a “handshake” procedure must be performed. This ECU ID communication is necessary to enable the Transponder ECU and the ECM to recognize each other before the vehicle will start. Complete ECU communication using the following steps: 1. Insert a Master key into the ignition cylinder. 2. Turn the ignition ON (engine OFF). 3. Short Tc and CG terminals of DLC3 using the Diagnostic Check Wire (SST 09843-18020 or equivalent) and leave for 30 minutes. 4. After 30 minutes, turn the ignition OFF and remove check wire from DLC3. 5. Register any additional keys as necessary. 6. Start the vehicle to confirm successful ECU communication. Key Programming: To program or delete a key, a registered Master key is necessary unless the Transponder ECU has been reset or replaced. The Transponder ECU system incorporates a black “Master” key and a gray “Sub” key. The process during registration of these two keys is identical. The key itself now determines if it functions as Master or Sub, not the registration procedure. The maximum number of allowable Master and Sub keys vary by model. Refer to the chart below.

Incoming search terms:

HONDA 2005 CBR 600 RR FULL S/S EXHAUST HEADER INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
Place the motorcycle in a vise or on it’s kick stand and make sure it is safe and secure. NOTE: If reusing the stock midpipe and muffler, skip ahead to step #5. 2) Remove the rider and passenger seats. Unplug the tail light, license plate light, and turn signals wires inside the tail section. 3) Remove the four bolts that secure the tail section to the subframe. Carefully remove the tail section from the subframe. 4) Remove the four bolts that secure the license plate/turn signal mount to the subframe. Remove the mount from the motorcycle. 5) Remove the upper and lower front fairing pieces. 6) Remove the two bolts that attach the right side footpeg assembly to the motorcycle. Disconnect the rear brake light switch and swing the footpeg assembly out of the way. Remove the outer plastic foot guard. Remove the aluminum heat shield from the motorcycle. 7) If equipped, remove the o2 sensor from the stock midpipe assembly.
NOTE: If reusing the stock midpipe and muffler, loosen the midpipe mounting bolts, and loosen the clamp securing the headpipe to midpipe connection. Skip ahead to step #9 8) Remove the midpipe mounting bolt, located on the right side of the subframe. Remove the
muffler mounting bolts. Lower the muffler and remove the rear exhaust section from the midpipe. 9) Remove the eight hex flange nuts securing the header flanges to the cylinder. 10)Remove the bottom header mounting bolt from the midpipe assembly. Remove the complete header from the motorcycle. 11)Remove the hat washer and rubber grommet from the stock midpipe assembly. Install the rubber grommet and hat washer into the hole provided on the Jardine midpipe assembly. 12)Slide the four headpipes into the new collectors. The headpipes are numbered from #1 thru #4, with #1 being the furthest toward the left side of the motorcycle, then work your way to the right. Do not install the provided springs at this time

HONDA CBR 600 RR AKRAPOVIC CARBON-FIBER PARTS installation instructions

0

Filed Under (Honda) by admin on 03-11-2011

download
INSTALLATION OF THE AKRAPOVIC CARBON-FIBER FRONT FENDER:
1. Make sure that the engine and the heated parts of the bike are cold before carrying out the following instructions.
2. Position the motorcycle on a side stand (we recommend a racing stand). Make sure, that surface is solid and flat.
3. Unscrew and remove bolts A on both sides of the motorcycle (Figure 1) ; unscrew the brake lines on both sides of
the motorcycle (Figure 2) and remove stock fender (Figure 3).
4. Reposition collars C and rubber mounts B (Figure 4, 5) from stock fender to Akrapovic carbon fiber fender
. Position the Akrapovic carbon-fiber fender in its location on the motorcycle, using stock bolts A (Figure 7, 8), re-
attach the brake lines on both sides of the motorcycle (Figure 9). Make sure that carbon-fiber fender is centered with
respect to the motorcycle and tighten bolts A securely

Incoming search terms:

Ducati 1098 and 1098S ECU connection Installation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
ECU can be connected to AIM loggers in two different ways: directly, or using the connector placed on the dashboard. 2.1. – Direct connection between AIM loggers and Marelli IAW 5AM2 ECU IAW 5AM2 is equipped with two 38 pins connectors, named “Body ” and “Engine” – see below: “engine” is black (on the left). “Body” connector is grey (on the right). To connect AIM loggers to Ducati ECU: • connect AIM cable labelled CAN+ to pin 20 of “Body” connector. • connect AIM cable labelled CAN- to pin 29 of “Body” connector. • Vbatt is on pin 17 (vehicle master switch). 2.2 – Dashboard connector Connector is equipped with 26 pins and it is placed on the back of the dashboard. To connect AIM loggers to ECU using the dashboard connector: • connect AIM cable labelled CAN+ to pin 19 (green/black twisted cable) connector. • connect AIM cable labelled CAN – to pin 26 (grey/green twisted cable) connector. • Vbatt is on pin 23 – red /black cable – vehicle master switch. Warning: to use Marelli dashboard , please remove 120 OHM resistance placed between CAN+ and CAN-; otherwise Marelli dash does not work

Incoming search terms:

1997 Honda CBR 1000 F specifications

0

Filed Under (Honda) by admin on 03-11-2010

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes. Pictures, trademarks and logos of third parties are exclusive property of the respective owners. Technical specifications are subject to change without notice. Bikez.com has been developed by low-cost software development company ObjectLabs

Incoming search terms:

Incoming search terms: