change lifter 883 sporster2006

You search Auto repair manual PDF change lifter 883 sporster2006, if there are search results will appear below. If search results do not exist, please search by others keyword.



  change lifter 883 sporster2006 Direct Download speed 5282 Kb/s

  change lifter 883 sporster2006 Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME BILLET LIFTER-COVER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
Installation with Stock Pushrods Refer to the service manual for your motorcycle model. Installation with Adjustable Pushrods Lifter-Cover Removal Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 1. Set the lifters of the rear cylinder to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 2. See Figure 1. Insert a screwdriver into the slot on the side of the spring-cap retainer on the pushrod cover. 3. Press the spring-cap and retainer down while pulling outward to remove the spring-cap retainer. 4. See Figure 2. Lift the lower pushrod cover to reveal the lower third of the pushrod. 5. If the engine has stock pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 6. If the engine already has adjustable pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 7 6. Use a bolt cutter or similar tool to cut the stock pushrod. Avoid cutting the pushrods with a saw, grinder, or other method that may allow metal debris into the engine. Go to step 8. 7. Loosen the jam nut on each adjustable pushrod and resize each rod to its shortest length. 8. Remove the pushrod covers and pushrods from the engine. 9. Remove the O-rings from the seats in the engine at the top and bottom of the pushrod cover. 10. Remove the four screws fastening the lifter cover to the engine to remove the cover and gasket. 11. Remove old lifter-cover gasket material from the engine, taking care not to allow material to fall into the engine. Continue to Lifter-Cover Installation in this I-Sheet. Lifter-Cover Installation 1. See Figure 3. Verify that the lifter anti-rotation pin is in position. Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 2. Verify that the cylinder lifters are set to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 3. Fasten the new lifter-cover gasket and chrome billet lifter cover to the engine using the chrome screws from this kit. In a cross pattern, torque the lifter-cover screws to 90 – 120 in-lbs (10.2 – 13.6 Nm). 4. See Figure 4. Loosen the jam nut on all of the pushrods and adjust the pushrods to their shortest length. NOTE See Figures 4 and 5. Install the narrow-band pushrods in the cylinder-intake location. Install the wide-band pushrods in the cylinder-exhaust location. 5. Assemble the O-rings (purchased separately) and pushrod covers. 6. Install the pushrods with the pushrod covers. The adjustment-end of the pushrod must be on the lifter

Incoming search terms:

1999 Toyota Camry LE V6 Body and Interior Maintenance Record

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner

Incoming search terms:

HARLEY DAVIDSON CHROME LIFTER BLOCK COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
INSTALLATION The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your motorcycle is available at any Harley- Davidson Dealer. NOTE Removal of the air cleaner assembly and, in cases where the bike has forward controls, shifter linkage will aid in installation of this kit. Remove the air cleaner and, if necessary, shifter linkage by following procedures in the appropriate Service Manual. 1. Remove the two rear most screws on the rear lifter cover. 2. See Figure 1. Install rear lifter cover bracket (1) assembly using screws (2) removed in step 1. Torque screws to 90- 120 in-lbs (10.0 – 13.5 Nm). 3. Remove the two screws most forward on the front lifter cover. 4. See Figure 2. Install front lifter cover bracket (1) assembly using screws (2) removed in step 3. Torque screws to 90- 120 in-lbs (10.0 – 13.5 Nm)

2007 Harley-Davidson CVO Family: Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
1. Harley-Davidson reserves the right to discontinue models or change specifications at any time without incurring any obligations. Vehicle specifications may vary by country and region depending on local laws. Some models are not available i certain countries. 1. Harley-Davidson reserves the right to discontinue models or change specifications at any time without incurring any obligations. Vehicle specifications may vary by country and region depending on local laws. Some models are not available in certain countries. 1. Harley-Davidson reserves the right to discontinue models or change specifications at any time without incurring any obligations. Vehicle specifications may vary by country and region depending on local laws. Some models are not available in certain countries. 2. Measurement reflects 81.7 kg operator weight. 2. Measurement reflects 81.7 kg operator weight. 2. Measurement reflects 81.7 kg operator weight. 3. Recommended 91 octane or higher fuel (R+M)/2 (87 octane or higher for XL 883 models). Standard and optional fuel systems may vary by country and region. 3. Recommended 91 octane or higher fuel (R+M)/2 (87 octane or higher for XL 883 models). Standard and optional fuel systems may vary by country and region. 3. Recommended 91 octane or higher fuel (R+M)/2 (87 octane or higher for XL 883 models). Standard and optional fuel systems may vary by country and region. 4. Standard and optional wheels may vary by country and region. 4. Standard and optional wheels may vary by country and region. 4. Standard and optional wheels may vary by country and region. 5. Values shown are nominal. Performance may vary by country and region. 5. Values shown are nominal. Performance may vary by country and region. 5. Values shown are nominal. Performance may vary by country and region. 6. Security systems include the immobiliser and siren. 6. Security systems include the immobiliser and siren. 6. Security systems include the immobiliser and siren. 7. Availability of colours may vary from dealer to dealer and is subject to change without notice. 7. Availability of colours may vary from dealer to dealer and is subject to change without notice. 7. Availability of colours may vary from dealer to dealer and is subject to change without notice. 8. Model not available in all markets. 8. Model not available in all markets. 8. Model not available in all markets. 9. See motorcycle owner’s manual for complete details. 9. See motorcycle owner’s manual for complete details. 9. See motorcycle owner’s manual for complete details. 10. Inspections of certain systems and components are required at 4,000 km intervals. 10. Inspections of certain systems and components are required at 4,000 km intervals. 10. Inspections of certain systems and components are required at 4,000 km intervals.

Incoming search terms:

MACHINE SPECIFICATION FOR 115cc (UNDERBONE) (4-stroke horizontal layout engine)

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
(This is for clarification only. Other parts not listed in Art. 2.5 & 2.6 can be altered or replaced. Change of specification means modification, changes or removal of the parts.) 2.6.1 Change of compression ratio is allowed. 2.6.2 Setting of carburetor, attachment or size change of air funnel. 2.6.3 Inlet opening of fuel tank for fuel charge may be modified but cannot be relocated. 2.6.4 Change of fuel pipe and fuel cork. 2.6.5 Change of exhaust pipe and muffler, but must have silencer. 2.6.6 Material of clutch discs and specifications of spring. Hand clutch is allowed. 2.6.7 Gear ratios are free. 2.6.8 Starting device and parts relative to this device may be removed. 2.6.9 Modification or removal of air cleaner box, wire harness and control wires. 2.6.10 Removal of speedometer (including meter gearbox and cable.) 2.6.11 Removal of drive chain case and cover. Change of drive chain is allowed. 2.6.12 Change of final gear ratio is allowed. 2.6.13 Attachment of bead stopper and balance weight to tyre. 2.6.14 Modification and change of rear brake part is allowed. 2.6.15 Frame body may be strengthened. 2.6.16 Modification and change to brackets and pedals including footrest. 2.6.17 Front suspension unit must remain as originally produced by the manufacturer. However, the following internal parts of the fork can be modified: Shims, hydraulic piston, oil passages, springs and spacers. 2.6.18 Attachment of stabilizer to strengthen or reinforcing rear swing arm is allowed. 2.6.19 Removal of dust seals. 2.6.20 Rear suspension unit must remain as originally produced by the manufacturer. However rear suspension unit is free. The rear linkage must remain as originally produced by the manufacturer. 2.6.21 Handle bars, clutch and front brake lever may be changed by an after market copy. Clutch springs may be changed. 2.6.22 Steering dampers may be fitted. They must not act in any way as a steering lock limiting device. 2.6.23 Materials of streamlining and material of seat cowling. (However, expensive materials such as carbon fibre and kevlar are not allowed). 2.6.24 Removal of rear mudguard and side cover. Front mudguard may be cut but not less than 6 inches from the front fork on original part. 2.6.25 All lubricants are free 2.6.26 Adjusting and polishing any parts are allowed. Adjusting is defined as : “To select each part or assembly complete with-in the limit of single or total tolerance” (i.e. that of valve clearance, ignition timing etc.) 2.6.27 Cutting unnecessary stays is

Harley-Davidson Evolution Engines, Hydraulic Lifter Limited Travel Kit Installation Manual

0

Filed Under (Harley Davidson) by admin on 23-10-2010

download
Remove tappet assemblies from engine being sure that each one is kept with it’soriginal tappet block. NOTE: This procedure is the preferred method of installation. However, kit can be installed without removing lifters from engine. 2. Remove hydraulic piston retaining wire clip from one assembly at a time. Be careful not to bend wire clip during disassembly. 3. Completely disassemble tappet removing all parts. 4. Thoroughly clean all parts including tappet body. Remove any oil which might prevent hydraulic unit from fully collapsing during adjustment. 5. Insert one spacer from S&S HL 2 Tkit in tappet body. 6. Reassemble tappet in reverse order making sure original parts arereturned to their original positions. See Picture1. 7. Replace wire retaining clip in tappet body. 8. Put tappet back in original tappet block. 9. Repeat Steps 2 through 8 for three remaining tappets. 10. Reassemble engine with modified tappets. 11. Adjust pushrods. NOTE – In all cases engine must be cold and lifter must be at lowest point of travel for pushrod adjustment To prevent accidents, remove ground cable from battery. A. Remove spark plugs. B. Bring piston to TDC on compression stroke in cylinder to be adjusted. Normally both tappets will be at their lowest point of travel. C. Extend pushrod adjustment, collapsing lifter until piston assembly is in contact with HL 2 Tspacer and pushrod is tight. If tappets contain oil, as when pushrods are readjusted after engine has been run, or if all oil was not removed during installation, extend pushrod adjustment until valve is open (about five additional turns of adjusting screw). Allow 5 minutes for hydraulic unit to bleed down. If pushrod can be turned with fingers after bleeding down, lifter is not completely collapsed, and this step must be repeated. NOTE – perform this operation on one cylinder at a time. Do not turn engine until pushrod adjustment is complete. Turning engine while valve is held off the seat could result in valve to valve or valve to piston contact and serious valve train damage. D. Loosen pushrod adjustment until pushrod can be rotated with the fingers with slight drag. NOTE – Shortening adjuster an additional six flats or full turn from zero lash often results in quieter pushrod operation. This provides additional travel for the hydraulic piston assembly, which can improve the ability of the hydraulic unit to maintain zerolash under normal operating conditions. E. Tighten lock nut. F. Follow the same procedure for all four push rods. G. Recheck pushrod adjustment after a few hundred miles. NOTES ● It is a good idea to recheck pushrod adjustment in a new engine as valve train may tighten up due to gasket compression and valve seat wear. ● Upon initial start up after modification, HL 2 Tequipped lifters may be somewhat noisy for 10-20 miles. If lifters are still noisy after 20 miles it is recommended that pushrods be adjusted 1⁄2 turnlooser. See step D

Incoming search terms:

TRIUMPH 750 BIG BORE CYLINDER AND PISTON SET FOR 650 TWINS INSTALLATION

0

Filed Under (Triumph) by admin on 29-10-2010

download
Step 1. Unpack your big bore kit and inspect the contents. There should be the following: 1. Cylinder x l 2. piston with wristpin x 2 3. Hepolite piston ring set x l 4. Special big bore head gasket Step 2. Thoroughly wash the cylinder bores with soap and water. Do not use solvent! Dry bores with air or a lint free towel and let completely air dry. This step is most important and will greatly extend the life of the pistons. Step 3. Following the procedure outlined in your service manual, drain the fuel tank, remove the exhaust system, fuel tank and carburetors. Have a catch basin handy to capture any fuel that may spill from the carburetors, as fuel is highly flammable and can be ignited by a dryer pilot light etc. from a long distance. Clean up any spilled fuel immediately and dispose of away from any source of ignition. Store the fuel tank in a well vented area, outdoors is best, in the event your fuel taps should leak. Step 4. Remove the rocker boxes by slacking the 9 head bolts a little at a time in a star pattern. Remove the 6 nuts at the front and back of the head. Remove the 4 corner rocker box bolts. Remove the head bolts and rocker boxes. Remove the push rods. Examine the push rods to insure they are straight and the ends are tight. Replace any suspect push rod. Step 5. Remove the cylinder head. Now would be a good time for guide and valve renewal. This is best left to an expert. More cylinder heads have been ruined by auto machine shops than by hard use. If you do not have a qualified shop in your area please call for a referral. Step 6. Remove the push rod tubes and the cylinder base nuts. Clip rubber bands around the top of the lifters to keep them from dropping into the crankcase. Have a few lint free rags handy. Bring the pistons to the top of the stroke and begin lifting off the cylinder. If the cylinder is hard to lift off, thread a nut on one of the base studs and use a tire lever to pry against the bottom fin close to its base using the stud as a fulcrum. After partially raising the cylinder stuff the crankcase mouth with rags to keep any carbon or broken rings from entering the crankcase. These will remain in place until step 12. Step 7. Leaving the rags in the crankcase remove the wrist pin circlips from the pistons and discard. Heat the piston and gently push the wrist pin out. Do not use force as this can damage the connecting rod or its bearings. Be sure to account for all the clips as one left in the crankcase can do extensive damage. Step 8. Clean all gasket surfaces to remove any traces of the old gaskets. Use Pennatex gasket remover if needed. Be very careful not to scratch the gasket surface or to allow any gasket particles to enter the crankcase. Even a small bit of gasket can stop the oil pump from working! Step 9. Note the direction and location of the lifters. These must be replaced in the same position as when removed. Remove the lifter blocks from the old cylinder. Start by removing the small retaining bolts and washers. The lifter blocks are extremely fragile and are easily broken. They are also very expensive so great care must be taken in this step! Triumph special tool 222-616008 is advisable here. Apply pressure to the center of the block only. Do not press against the tangs that locate the lifter! A tool can be fabricated using two dowels to locate in the lifter holes. Step 10. Clean and examine the lifters and camshaft faces. Clean the lifter blocks and remove the sealing oring under the locating flange. Replace these with the new orings in the gasket set. Apply a smear of gasket sealant to the lifter block oring and press into the new cylinder. Be sure the lifter block is parallel with the bores and the grooved block is on the exhaust side. Apply a small amount of assembly oil to the lifters and replace in the exact position they came from

Incoming search terms:

Harley-Davidson Sportster 883/ 1200 Straightshot HS Exhaust system REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the two bolts from each muffler body which attach the muffler bodies to the mounting bar. 4. Remove the clamp bolt which mounts the rear head Page 1 of 4 D445N Rev. 1.0 Sportster 883/1200 Straightshot HS Exhaust system Part #17815 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 3/16″ & 5/16″ Allen wrenches 3/16″ & 5/16″ Allen & 1/2″ sockets 3/8″ Ratchet & Extensions T30 Torx driver 1/2″ Wrench 5/16″ nutdriver/flat blade screwdriver Ft/lb. & In/lb. Torque wrenches Snapring pliers pipe to the belt drive cover bracket and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. NOTE: If circlips look bent or twisted replace them with new circlips. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets part number 17048-98. 2. Install and tighten supplied mounting bracket (stamped 356-P) using stock bolts and washers (Figure 1). Torque to 30-33 Ft/Lbs. NOTE: Support the rear of the bracket during tightening to insure it is aligned with the bottom edge of the frame. 3. Re-install drive belt cover. Torque to 1 x 3/8″ bolt 30-33 Ft/Lbs. 2 x 1/4″ bolts 80-120 In/Lbs. 4. Re-install brake rod eyelet using blue thread locking compound (Loctite® 243). There is a 1/2″ clearance hole in the bracket to allow access for tightening brake rod eyelet. Torque to 120/180 In/Lbs. (Figure 1). 5. Remove header pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips where hose clamps will loop through (Figure 2). 6. Install circlips and flanges from the stock system onto both new head pipes.

Incoming search terms:

Harley-Davidson XL 883 and 1200 MODELS SADDLEBAG SUPPORT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 27-04-2012

download
1. 1994-99 models: Remove upper shock absorber nut, washer, shock cover and backing washer. Save nut and washer and discard shock cover and backing washer. 2000-03 models: Remove upper shock bolt, washer and shock cover and save washer. NOTE: Do not remove stock inboard washer that is positioned behind shock cover and against shock absorber. 2. All models: Remove OEM buttonhead screw and flanged nut directly to the rear of the upper shock mount on fender support. Note T-spacer in fender support. Save nut and discard bolt. 3. 1994-99 models: Position saddlebag support (item 1) with front bracket over shock stud and rear mount over hole in fender support. Install ½ * bushing (Item 2) over shock stud and into hole of support front mount. Install saved OEM nut and washer (items 3,4) and tighten securely. 2000-03 models: Apply Locktite to the OEM shock screw (Item 5) and install through the saved washer (Item 6), front bracket of the saddlebag support (Item 1), shock and into the frame. Tighten to 21-35 ft. -lbs torque. NOTE: If installing supports with sissy bar side plates, omit 5/16 * lock washer (Item 8). H-D sissy bar side plate mounts between fender support and fender. Khrome Werks® sissy bar plate mounts outboard of fender support. CAUTION: Be careful to not dislodge T-spacer from its position in fender while inserting screw through fender support and fender. 4. Insert supplied socket head cap screw (Item 7) and lock washer (Item 8) (if applicable) through the rear saddlebag support mount, sissy bar side plate (if applicable) , fender with T-spacer and frame. Apply Loctite to the saved flanged nut and secure. Tighten to 8-13 ft-lbs torque.

Harley-Davidson feuling Adjustable Pushrods Installation Instructions

0

Filed Under (Harley Davidson) by admin on 22-04-2012

download
1. Refer to the proper factory service manual for your model and year of engine, for removal of existing pushrods. 2. The Feuling pushrods are designed with a small adjustment parameter for rigidity creating maximum lift – These are not quick install pushrods and may require the removal of the lifter blocks and or loosing of the breathers/rocker arms supports. When loosening the rocker arm supports always remove the breather bolts first. 3. Clean and inspect each new Feuling pushrod including center oil hole 4. Feuling pushrods are marked Intake and Exhaust. The shorter pushrods are Intake and the longer pushrods Exhaust 5. Feuling recommends using new O-rings and gaskets where applicable to prevent oil leaks
6. Always pump up hydraulic lifters before installing them. Use an oil squirt can to fill the lifter with oil through the feed hole on the side of the lifter, push oil through the feed hole until the air bubbles are gone. If needed work the oil back and forth through the feed hole and pushrod seat with the squirt can. Light weight oil can be helpful. 7. Assemble and adjust one cylinder at a time, the servicing cylinder needs to be on TDC of compression stroke so the cam lobes are at their lowest point 8. Install pushrods into proper locations with the adjusting side of the pushrod down, towards the lifter. Slide the pushrods through the pushrod covers up into the rocker housing and set the pushrod on the seat of the lifter. We recommend filling the pushrods with oil then maneuver the pushrod up into the rocker arm seat. 9. Torque rocker arm housings and breathers to factory torque spec’s 10. See the instructions for your lifters for the proper adjustment. All Feuling hydraulic lifters run best at . 090″ – . 100″ of crush.

Incoming search terms:

Incoming search terms: