changing 2008 toyota tacoma antenna

You search Auto repair manual PDF changing 2008 toyota tacoma antenna, if there are search results will appear below. If search results do not exist, please search by others keyword.



  changing 2008 toyota tacoma antenna Direct Download speed 5282 Kb/s

  changing 2008 toyota tacoma antenna Full Version speed 6162 Kb/s



HARLEY DAVIDSON ADVANCED AUDIO CB ANTENNA KIT (FRAME MOUNT) INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
This kit fits 2006 and later FLHT (Electra Glide®), FLHTC (Electra Glide Classic), FLHX (Street GlideTM) and FLTR (Road Glide®) model motorcycles. INSTALLATION 1. Refer to the Service Manual and follow the instructions given to remove the right-side saddlebag. 2. See Figure 1. Obtain the antenna bracket (5) from the kit. 3. Mount the antenna bracket to the right-side saddlebag rear support bracket (1). In the upper hole (2), use a 5/16-18 x 5/8 in. in. screw and lockwasher from the kit. If NO saddlebag guard (4), use a 5/16-18 x 5/8 in. screw and lockwasher from the kit to attach the antenna bracket to the lower hole (3) in the support bracket. If a saddlebag guard (4) is mounted, remove and discard the original upper rear guard mounting screw. Use the 5/16-18 x 7/8 in. screw and lockwasher from the kit to attach the antenna bracket and guard at the lower hole (3) in the support bracket. 4. Tighten the mounting screws to 19 ft-lbs (26 Nm). 5. FLHX models: Remove and discard the hole plug from the right-side rear fender fascia (ground effects). 6. See Figure 2. Obtain the antenna adapter (4), two set screws (5) and the antenna base (6) from the kit. Thread the set screws part way into the holes in the side of the adapter. Thread the antenna adapter onto the antenna base. 7. Thread one of the 1/2-20 thin nuts (7) from the kit onto the antenna base assembly. Place the large internal tooth lockwasher (8) on the threads of the antenna base and insert the antenna base, from the top, through the hole in the antenna mounting bracket. 8. Install the second 1/2-20 nut on the antenna base threads. Place a wrench on the upper nut and tighten the lower nut to 40 in-lbs (4.5 Nm). 9. FLHX models: Install the CB antenna grommet (Part Number 59778-06, sold separately) into the opening in the right-side rear fender fascia. 10. Thread the loading coil (2) into the top of the antenna adapter

Incoming search terms:

HARLEY DAVIDSON AM/FM ANTENNA RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Owner’s Manual and follow the instructions given to remove the left-side saddlebag. Gently pull the left-side cover from the frame downtubes (no tools are required), and remove the main fuse. 2. See Figure 1. Disconnect the antenna cable from the antenna base assembly (1). 3. Unscrew the antenna mast (2) from the antenna base, and set it aside for later installation. 4. Remove the lower locknut (3), and remove the antenna base from the mounting bracket (5). Save both locknuts, but discard the lockwasher (4). 5. Remove the two TORX® head screws (6) and lockwashers (7) retaining the antenna mounting bracket to the saddlebag rear support bracket (8). Discard the bracket and fasteners. 6. Carefully remove and discard any cable straps securing the antenna cable to the fender support and saddlebag rear support brackets. 8 9 6 3 2 5 7 4 3 1 is05436 1. Antenna base assembly 2. Antenna mast 3. Locknut (2) 4. Lockwasher 5. Original antenna mounting bracket 6. TORX head screw (2) 7. Split lockwasher (2) 8. Saddlebag rear support bracket 9. TORX Pan head screw and flanged locknut Figure 1. Original Antenna Mount 7. Remove and discard the TORX head screw and nut (9) that fastens the lower saddlebag support bar to the rear fender support bracket. 8. See Figure 2. Obtain the new antenna bracket (1), button head screw (2), flat washers (3 and 4) and flange nut (5) from the kit. NOTE If V-Logo Rear Fender Trim Rail Kit 91100-09 has been installed, the thick washer (4) is not used, and can be dis- carded.

Incoming search terms:

HARLEY DAVIDSON ROAD TECH XM SATELLITE RADIO RECEIVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION NOTE Do not use solvent-based chemicals or waxes directly on the plastic or rubber components as they can affect the overall performance and appearance of the plastic and rubber. Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) -J03989 1 of 8
Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Receiver Mounting Bracket Installation When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. ALL models: See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 3. Using a T-27 TORX drive head, remove the two screws that retain the clutch-lever clamp to the handlebar. 4. See Figure 4. Obtain the correct mounting bracket (2) for your vehicle, and two button-head screws (3) and spacers (4) from the kit. Insert the button-head screws into the mounting bracket, through the holes above and below the slot. Place a spacer over the threads of each screw. Insert the screw threads into the holes in the clutch lever clamp removed earlier. 5. Adjust the hand lever position for rider comfort and posture, then tighten the screws to 60-80 in-lbs (6.8-9.0 Nm) . Receiver and Antenna Bracket Installation 6. Obtain the satellite radio receiver (1), antenna bracket (6), and four lock nuts (8) from the kit. Insert the four studs on the back of the receiver through the four holes in the receiver mounting bracket. 7. See Figure 4 for mounted position of the antenna bracket to the receiver mounting bracket. Assemble a lock nut to each of the bottom two studs. Install the antenna bracket onto the top two studs, and assemble a lock nut to each top stud. Tighten the locknuts securely. Antenna Installation 8. Obtain the XM radio antenna (5) and two-sided adhesive tape (7) from the kit. 9. Use isopropyl alcohol to clean the horizontal antenna mounting surface of the antenna bracket, and the bottom (mounting) surface of the antenna. 10. Peel the liner from one side of the tape, and apply the tape squarely to the bottom surface of the antenna. 11. Peel the liner from the exposed side of the adhesive tape on the antenna base. 12. Position the antenna over the bracket without touching the adhesive to the bracket. Center the antenna over the bracket with the antenna cable toward the center of the vehicle. 13. Press the antenna squarely and firmly onto the bracket, and hold pressure for about 60 seconds. After releasing pressure, avoid direct contact with the antenna for about 20 minutes. HARNESS ROUTING AND CONNECTION

Incoming search terms:

ROAD TECH XM SATELLITE RADIO RECEIVER KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) -J03989 1 of 8 Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Receiver Mounting Bracket Installation When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. ALL models: See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 3. Using a T-27 TORX drive head, remove the two screws that retain the clutch-lever clamp to the handlebar. 4. See Figure 4. Obtain the correct mounting bracket (2) for your vehicle, and two button-head screws (3) and spacers (4) from the kit. Insert the button-head screws into the mounting bracket, through the holes above and below the slot. Place a spacer over the threads of each screw. Insert the screw threads into the holes in the clutch lever clamp removed earlier. 5. Adjust the hand lever position for rider comfort and posture, then tighten the screws to 60-80 in-lbs (6.8-9.0 Nm) . Receiver and Antenna Bracket Installation 6. Obtain the satellite radio receiver (1), antenna bracket (6), and four lock nuts (8) from the kit. Insert the four studs on the back of the receiver through the four holes in the receiver mounting bracket. 7. See Figure 4 for mounted position of the antenna bracket to the receiver mounting bracket. Assemble a lock nut to each of the bottom two studs. Install the antenna bracket onto the top two studs, and assemble a lock nut to each top stud. Tighten the locknuts securely. Antenna Installation 8. Obtain the XM radio antenna (5) and two-sided adhesive tape (7) from the kit. 9. Use isopropyl alcohol to clean the horizontal antenna mounting surface of the antenna bracket, and the bottom (mounting) surface of the antenna. 10. Peel the liner from one side of the tape, and apply the tape squarely to the bottom surface of the antenna. 11. Peel the liner from the exposed side of the adhesive tape on the antenna base. 12. Position the antenna over the bracket without touching the adhesive to the bracket. Center the antenna over the bracket with the antenna cable toward the center of the vehicle. 13. Press the antenna squarely and firmly onto the bracket, and hold pressure for about 60 seconds. After releasing pressure, avoid direct contact with the antenna for about 20 minutes. HARNESS ROUTING AND CONNECTION NOTE Route the satellite radio receiver harness along the outside of the handlebar, even on internally-wired handlebars. 1. Route the unconnected end of the satellite radio receiver harness as follows: a. Follow the existing wiring from the left-side handlebar switches over to the center of the handlebar. Temporarily bind the harness in place as you route the harness along the handlebar to the center. Do not permanently wire tie the harness to the handlebar at this time. b. Route the wires down through the upper fork bracket (triple clamp), past the steering head, and back along the frame backbone toward the seat. Follow existing wiring where practical. For FLHT, FLHTC, FLHTCU, FLHX models , it may be necessary to remove the inner fairing cap to secure the wires. c. Locate the main harness chassis ground connection on the frame. See the Service Manual for your model and year vehicle for specific location. Remove the ground screw or nut. d. Select the appropriate ring terminal (9 or 10) to fit the ground screw or stud

Incoming search terms:

TOYOTA ALL MODELS AM STATIC NOISE ON VEHICLES WITH POWER ANTENNAS

0

Filed Under (Toyota Manuals) by admin on 16-10-2011

download
Vehicles with power antennas may exhibit audible electrical noise on weak AM stations when various electrical accessories (turn signals, rear defogger, cruise control, brakes, etc.) are operated. Poor antenna grounding can cause this condition. To eliminate or reduce the intensity of the noise, use the following repair procedure: AM STATIC NOISE ON VEHICLES WITH POWER ANTENNAS Page 1 of 2 OCTOBER 25, 1996 AUDIO AU002-96 ALL MODELS REPAIR PROCEDURE: 1. Tune the radio to a strong, static-free AM station and slowly move the tip of the antenna
mast forward and back approximately 2 inches (Fig. 1). If static noise is not heard, go to Step 2. If static noise is heard during antenna movement, replace the antenna mast and go to Step 3. NOTE: Do not touch the antenna mast with your bare hands. Use a glove or nonmetallic object to move the antenna. (If you touch the antenna with your hands, you will change the antenna sensitivity). 2. Remove the antenna mast and inspect the base of the mast for corrosion and damage (Fig. 2). Clean with 1500 grit sandpaper. 3. Remove the antenna assembly and inspect the inner fender around the antenna hole for corrosion (Fig. 3). Clean with 1500 grit sandpaper.

2005-2008 TOYOTA TACOMA/ TUNDRA

0

Filed Under (Toyota Manuals) by admin on 09-06-2011

Download
anti-Skid Brakes (ABS) STD Global Outstanding Assessment body (GOA) STD Toyota Safe-T-Cell STD Driver’s SRS airbag STD Front passenger SRS airbag STD Driver’s pre-tensioner seatbelt STD Driver’s forcelimiter eatbelt STD Front passenger pre-tensioner seatbelt STD Front passenger forcelimiter seatbelt STD Height adjustable front seatbelts STD 2nd row/rear seat centre position lap/sash seatbelt STD 3rd row lap/sash outboard seatbelts STD 2nd row/rear seat ALR outboard seatbelts for child seats STD

TOYOTA TACOMA 2008 – INTERFACE KIT FOR IPOD REPAIR

0

Filed Under (Toyota Manuals) by admin on 01-11-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as: • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Vehicle Protection. (a) Place driver seat in mid position. (b) Set emergency brake. (c) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. CAUTION: Do not touch the positive terminal with any tool when removing cable. (d) Using protective blankets cover front seats, interior of vehicle and center console and front side of the shift lever. (e) Wait 90 seconds before proceeding to disassemble vehicle. 2. Disassembly of Vehicle. NOTE: Place all removed parts on a protected surface. NOTE: When disconnecting wiring connectors, do not pull on the wiring; pull on the connector only. (a) Remove air conditioning control assembly (L,R). (Fig. 2-1) (1) Apply protective tape. (2) Using a panel remover, disengage the four (4) clips and remove the air conditioning control assembly

Toyota Tacoma Truck – 2010 Performance & Specifications

0

Filed Under (Toyota Manuals) by admin on 28-09-2011

download

Toyota strives to build vehicles to match customer interest and thus they typically are built with popular options and option packages. Not all options/packages are available separately and some may not be available in all regions of the country. If you would prefer a vehicle with no or different options, contact your dealer to check for current availability or the possibility of placing a special order. Toyota Tacomas are designed to meet most off-road driving requirements. Abusive use may result in bodily harm or damage. Toyota encourages responsible operation to protect you, your vehicle and the environment. Some vehicles are shown with available equipment. Seatbelts should be worn at all times. Please do not allow passengers to ride in the cargo area. Towing hitch receivers/ball mount kits are not intended to provide crash protection. For details on vehicle specifications, standard features and available equipment in your area, contact your Toyota dealer. A vehicle with particular equipment may not be available at the dealership. Ask your Toyota dealer to help locate a specifically equipped vehicle. All information presented herein is based on data available at the time of posting, is subject to change without notice and pertains specifically to mainland U.S.A. vehicles only

Incoming search terms:

2003 – 2008 4Runner AND 2007 – 2008 FJ Cruiser FRONT AND REAR DIFFERENTIAL GEAR OIL SPECIFICATION CHANGE

0

Filed Under (Toyota Manuals) by admin on 14-11-2011

download
75W-85 GL5 synthetic gear oil beginning with the 2008 model year. This new synthetic gear oil is compatible with 2003 – 2007 model year 4Runner and 2007 model year FJ Cruiser differentials. Please refer to the Parts Information section below for information about this gear oil and use this gear oil (or equivalent) when filling front or rear differentials with oil. 2003 – 2008 model year 4Runner vehicles. 2007 – 2008 model year FJ Cruiser vehicles. PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME TYPE QTY N/A 08885-02606 Toyota Genuine Differential Gear Oil LX 75W-85 API GL-5 SAE 75W-85 LSD As Needed N/A 08885-02506 Toyota Genuine Differential Gear Oil LT 75W-85 API GL-5 SAE 75W-85 w/o LSD As Needed Refer to the diagram below to identify if LSD or non-LSD gear oil is used on the vehicle. For applicable vehicles, there is a caution label above the filler plug, as shown below

Incoming search terms:

FLUID SPECS MODEL- YEAR 1994- 2005 FOR TOYOTA CAMRY, COROLLA AND TACOMA

0

Filed Under (Toyota Manuals) by admin on 17-09-2011

Download
Toyota Genuine Motor Oil 5W-30 Toyota Genuine Motor Oil 10W-30 Ethylene-Glycol Antifreeze Toyota Long Life Coolant Toyota Super Long Life Coolant 00272-SLLC2 Hypoid API GL-5 75W-90 Gear Lube T-IV Transmission Fluid ATF WS Transmission Fluid 08885-80306 Good brand of 80W-90 gear lube Hypoid API GL-5 80W-90 Gear Lube Castle V160 Gear Lube Sequential Manual Transmission Fluid 08885-01306 08886-02206 Synthetic Hypoid API GL-5 75W-140 Gear Lube Limited Slip Gear Oil

Incoming search terms:

Incoming search terms: