changing antenna on 2010 ultra

You search Auto repair manual PDF changing antenna on 2010 ultra, if there are search results will appear below. If search results do not exist, please search by others keyword.



  changing antenna on 2010 ultra Direct Download speed 5282 Kb/s

  changing antenna on 2010 ultra Full Version speed 6162 Kb/s



HARLEY DAVIDSON ADVANCED AUDIO CB ANTENNA KIT (FRAME MOUNT) INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
This kit fits 2006 and later FLHT (Electra Glide®), FLHTC (Electra Glide Classic), FLHX (Street GlideTM) and FLTR (Road Glide®) model motorcycles. INSTALLATION 1. Refer to the Service Manual and follow the instructions given to remove the right-side saddlebag. 2. See Figure 1. Obtain the antenna bracket (5) from the kit. 3. Mount the antenna bracket to the right-side saddlebag rear support bracket (1). In the upper hole (2), use a 5/16-18 x 5/8 in. in. screw and lockwasher from the kit. If NO saddlebag guard (4), use a 5/16-18 x 5/8 in. screw and lockwasher from the kit to attach the antenna bracket to the lower hole (3) in the support bracket. If a saddlebag guard (4) is mounted, remove and discard the original upper rear guard mounting screw. Use the 5/16-18 x 7/8 in. screw and lockwasher from the kit to attach the antenna bracket and guard at the lower hole (3) in the support bracket. 4. Tighten the mounting screws to 19 ft-lbs (26 Nm). 5. FLHX models: Remove and discard the hole plug from the right-side rear fender fascia (ground effects). 6. See Figure 2. Obtain the antenna adapter (4), two set screws (5) and the antenna base (6) from the kit. Thread the set screws part way into the holes in the side of the adapter. Thread the antenna adapter onto the antenna base. 7. Thread one of the 1/2-20 thin nuts (7) from the kit onto the antenna base assembly. Place the large internal tooth lockwasher (8) on the threads of the antenna base and insert the antenna base, from the top, through the hole in the antenna mounting bracket. 8. Install the second 1/2-20 nut on the antenna base threads. Place a wrench on the upper nut and tighten the lower nut to 40 in-lbs (4.5 Nm). 9. FLHX models: Install the CB antenna grommet (Part Number 59778-06, sold separately) into the opening in the right-side rear fender fascia. 10. Thread the loading coil (2) into the top of the antenna adapter

Incoming search terms:

HARLEY DAVIDSON AM/FM ANTENNA RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Owner’s Manual and follow the instructions given to remove the left-side saddlebag. Gently pull the left-side cover from the frame downtubes (no tools are required), and remove the main fuse. 2. See Figure 1. Disconnect the antenna cable from the antenna base assembly (1). 3. Unscrew the antenna mast (2) from the antenna base, and set it aside for later installation. 4. Remove the lower locknut (3), and remove the antenna base from the mounting bracket (5). Save both locknuts, but discard the lockwasher (4). 5. Remove the two TORX® head screws (6) and lockwashers (7) retaining the antenna mounting bracket to the saddlebag rear support bracket (8). Discard the bracket and fasteners. 6. Carefully remove and discard any cable straps securing the antenna cable to the fender support and saddlebag rear support brackets. 8 9 6 3 2 5 7 4 3 1 is05436 1. Antenna base assembly 2. Antenna mast 3. Locknut (2) 4. Lockwasher 5. Original antenna mounting bracket 6. TORX head screw (2) 7. Split lockwasher (2) 8. Saddlebag rear support bracket 9. TORX Pan head screw and flanged locknut Figure 1. Original Antenna Mount 7. Remove and discard the TORX head screw and nut (9) that fastens the lower saddlebag support bar to the rear fender support bracket. 8. See Figure 2. Obtain the new antenna bracket (1), button head screw (2), flat washers (3 and 4) and flange nut (5) from the kit. NOTE If V-Logo Rear Fender Trim Rail Kit 91100-09 has been installed, the thick washer (4) is not used, and can be dis- carded.

ROAD TECH XM SATELLITE RADIO RECEIVER KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) -J03989 1 of 8 Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Receiver Mounting Bracket Installation When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. ALL models: See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 3. Using a T-27 TORX drive head, remove the two screws that retain the clutch-lever clamp to the handlebar. 4. See Figure 4. Obtain the correct mounting bracket (2) for your vehicle, and two button-head screws (3) and spacers (4) from the kit. Insert the button-head screws into the mounting bracket, through the holes above and below the slot. Place a spacer over the threads of each screw. Insert the screw threads into the holes in the clutch lever clamp removed earlier. 5. Adjust the hand lever position for rider comfort and posture, then tighten the screws to 60-80 in-lbs (6.8-9.0 Nm) . Receiver and Antenna Bracket Installation 6. Obtain the satellite radio receiver (1), antenna bracket (6), and four lock nuts (8) from the kit. Insert the four studs on the back of the receiver through the four holes in the receiver mounting bracket. 7. See Figure 4 for mounted position of the antenna bracket to the receiver mounting bracket. Assemble a lock nut to each of the bottom two studs. Install the antenna bracket onto the top two studs, and assemble a lock nut to each top stud. Tighten the locknuts securely. Antenna Installation 8. Obtain the XM radio antenna (5) and two-sided adhesive tape (7) from the kit. 9. Use isopropyl alcohol to clean the horizontal antenna mounting surface of the antenna bracket, and the bottom (mounting) surface of the antenna. 10. Peel the liner from one side of the tape, and apply the tape squarely to the bottom surface of the antenna. 11. Peel the liner from the exposed side of the adhesive tape on the antenna base. 12. Position the antenna over the bracket without touching the adhesive to the bracket. Center the antenna over the bracket with the antenna cable toward the center of the vehicle. 13. Press the antenna squarely and firmly onto the bracket, and hold pressure for about 60 seconds. After releasing pressure, avoid direct contact with the antenna for about 20 minutes. HARNESS ROUTING AND CONNECTION NOTE Route the satellite radio receiver harness along the outside of the handlebar, even on internally-wired handlebars. 1. Route the unconnected end of the satellite radio receiver harness as follows: a. Follow the existing wiring from the left-side handlebar switches over to the center of the handlebar. Temporarily bind the harness in place as you route the harness along the handlebar to the center. Do not permanently wire tie the harness to the handlebar at this time. b. Route the wires down through the upper fork bracket (triple clamp), past the steering head, and back along the frame backbone toward the seat. Follow existing wiring where practical. For FLHT, FLHTC, FLHTCU, FLHX models , it may be necessary to remove the inner fairing cap to secure the wires. c. Locate the main harness chassis ground connection on the frame. See the Service Manual for your model and year vehicle for specific location. Remove the ground screw or nut. d. Select the appropriate ring terminal (9 or 10) to fit the ground screw or stud

HARLEY DAVIDSON ROAD TECH XM SATELLITE RADIO RECEIVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION NOTE Do not use solvent-based chemicals or waxes directly on the plastic or rubber components as they can affect the overall performance and appearance of the plastic and rubber. Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) -J03989 1 of 8
Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Receiver Mounting Bracket Installation When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. ALL models: See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 3. Using a T-27 TORX drive head, remove the two screws that retain the clutch-lever clamp to the handlebar. 4. See Figure 4. Obtain the correct mounting bracket (2) for your vehicle, and two button-head screws (3) and spacers (4) from the kit. Insert the button-head screws into the mounting bracket, through the holes above and below the slot. Place a spacer over the threads of each screw. Insert the screw threads into the holes in the clutch lever clamp removed earlier. 5. Adjust the hand lever position for rider comfort and posture, then tighten the screws to 60-80 in-lbs (6.8-9.0 Nm) . Receiver and Antenna Bracket Installation 6. Obtain the satellite radio receiver (1), antenna bracket (6), and four lock nuts (8) from the kit. Insert the four studs on the back of the receiver through the four holes in the receiver mounting bracket. 7. See Figure 4 for mounted position of the antenna bracket to the receiver mounting bracket. Assemble a lock nut to each of the bottom two studs. Install the antenna bracket onto the top two studs, and assemble a lock nut to each top stud. Tighten the locknuts securely. Antenna Installation 8. Obtain the XM radio antenna (5) and two-sided adhesive tape (7) from the kit. 9. Use isopropyl alcohol to clean the horizontal antenna mounting surface of the antenna bracket, and the bottom (mounting) surface of the antenna. 10. Peel the liner from one side of the tape, and apply the tape squarely to the bottom surface of the antenna. 11. Peel the liner from the exposed side of the adhesive tape on the antenna base. 12. Position the antenna over the bracket without touching the adhesive to the bracket. Center the antenna over the bracket with the antenna cable toward the center of the vehicle. 13. Press the antenna squarely and firmly onto the bracket, and hold pressure for about 60 seconds. After releasing pressure, avoid direct contact with the antenna for about 20 minutes. HARNESS ROUTING AND CONNECTION

Incoming search terms:

HARLEY DAVIDSON DETACHABLE TOUR-PAK KIT FOR ELECTRA GLIDE CLASSIC INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Install Docking Kits and License Plate Holder 1. Install Rear Detachable Docking kit. Refer to the instruction sheet provided with kit. 2. Install Touring Detachable Tour-Pak Rack. Refer to the instruction sheet provided with kit. 1 4 2 3 is03989 1. License Plate Holder 2. Red Reflector 3. Original Equipment Screws 4. Original Equipment Bottom Support Tube Figure 2. Install License Plate Holder 3. See Figure 2. Install the new license plate holder (1) to the bottom support tube (4) using screws (3) saved from prior step. 4. Remove adhesive backing from red reflector (2) and carefully center and align it with the bottom edge of the license plate holder (1) and press firmly into place. -J03930 1 of 4 MOUNTING ANTENNA RELOCATION BRACKET 1. See Figure 6. Assemble joint assembly (9) to antenna mounting bracket (6) using lock washer (5) and 2 hex nuts (4). Tighten hardware securely. 2 1 5 4 3 is03992 1. Rear Docking Point 2. Docking Point Support Bracket 3. Antenna Mounting Bracket 4. Antenna/Cable Adapter 5. Rear Docking Point Screw and Locknut Figure 3. Relocated Antenna Bracket and Cable 2. See Figure 3. Install assembled antenna bracket (3) by removing screw and locknut (5) securing left rear docking point (1) to docking support (2). Install bracket as shown and reinstall rear docking point screw and locknut. Tighten screw and locknut to 15-19 ft-lbs (20.3-25.7 Nm) . 3. Thread antenna/cable adapter (4) onto joint assembly. ROUTING ANTENNA CABLES 1. See Figure 4. Gently remove left side cover (1) by pulling from frame tubes (no tools required). 2. Connect original antenna cable (not shown) to bottom of joint assembly. 3. Route antenna cable/wiring between left frame rail and fender. 4. See Figure 5. Attach cable to docking point support bracket in location (1) using short cable strap. 5. See Figure 4. Coil excess antenna cable/wiring (2) and use long cable strap (3) to fasten cable to frame under left side cover (1) with vehicle wiring harness. 6. See Figure 6. Cap unused wiring connector with connector housing (10).

TOYOTA ALL MODELS AM STATIC NOISE ON VEHICLES WITH POWER ANTENNAS

0

Filed Under (Toyota Manuals) by admin on 16-10-2011

download
Vehicles with power antennas may exhibit audible electrical noise on weak AM stations when various electrical accessories (turn signals, rear defogger, cruise control, brakes, etc.) are operated. Poor antenna grounding can cause this condition. To eliminate or reduce the intensity of the noise, use the following repair procedure: AM STATIC NOISE ON VEHICLES WITH POWER ANTENNAS Page 1 of 2 OCTOBER 25, 1996 AUDIO AU002-96 ALL MODELS REPAIR PROCEDURE: 1. Tune the radio to a strong, static-free AM station and slowly move the tip of the antenna
mast forward and back approximately 2 inches (Fig. 1). If static noise is not heard, go to Step 2. If static noise is heard during antenna movement, replace the antenna mast and go to Step 3. NOTE: Do not touch the antenna mast with your bare hands. Use a glove or nonmetallic object to move the antenna. (If you touch the antenna with your hands, you will change the antenna sensitivity). 2. Remove the antenna mast and inspect the base of the mast for corrosion and damage (Fig. 2). Clean with 1500 grit sandpaper. 3. Remove the antenna assembly and inspect the inner fender around the antenna hole for corrosion (Fig. 3). Clean with 1500 grit sandpaper.

HARLEY DAVIDSON SHORT CB ANTENNA MAST REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
Additional Parts Required 1998 through 2008 models require use of the original equipment (OE) load coil. 2009 and later models DO NOT require use of a load coil. Kit Contents There are no service parts available with this kit. INSTALLATION 1. 2008 and earlier models: Use a 2 mm hex key to loosen the bottom set screw of the antenna mast. ALL models: Unscrew the antenna mast from the antenna base. 2. Thread the new antenna mast onto the threads of the antenna base. IN SERVICE 2008 and earlier models: If a degradation of CB performance is detected: 1. Open the Tour-Pak. 2. Open the map pocket (if present), and remove the acorn nuts with flat washers. Remove the map pocket and molded liner from the Tour-Pak. 3. Check the routing of the load coil wiring (see Figure 2). Wire routing other than as shown can cause a degradation of the CB signal

Toyota 2007- 2010 Camry 2009- 2010 Venza INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 25-09-2011

download
Turn the ignition OFF and disconnect the vehi- cle’s negative battery cable Disconnect the mass sensor electrical connection by depressing the center tab and gently pulling the harness away from the mass air sensor. Release the
two wiring harness clips from the air box lid ently pull the engine cover upward to release it from the mounting grommets. Once released, Re- move engine cover from the vehicle and set aside. 4. Disconnect the vacuum line from the intake mani- fold plenum connection. 5. Disconnect the vacuum line from the upper air box lid. Toyota
2007-10 Camry 2009-10 Venza V6-3.5L 69-8611 7. Disconnect the two vacuum lines from the “Vacuum switching valve.

Incoming search terms:

2010 Harley-Davidson New Model and Technical Information

0

Filed Under (Harley Davidson) by admin on 15-12-2010

download
Meet MY2010 EPA Emissions regulations for all Harley- Davidson®vehicles sold in 50 state and Canadian markets •Reduce oxygen intrusion into the exhaust system -Promotes catalyst health and efficiency New rib/curl pipe end feature offers positive muffler stop and improved pipe consistency. 2010 Dyna®Models Crossover joints updated with new clamp and gasket. Updated joint New clamp (Comes w/gasket) New Gasket Torque 15-19 ft-lbs (20.3-25.8 Nm) 2010 Dyna®Models New 2010 FXDWG Wide Glide® New 2010 FXDWG Wide Glide® New rear fender New Floating Front Brake Rotors* New fuel tank with wider tunnel* *All Dyna®Models Current FXDB solo seat with new cover New sissybar New pillion Current FXDWG front forks with 1″shorter overall length Current FXDWG front wheel (steel) (21×2.15) black rim with chrome spokes & machined hub; Front tire pattern -GT402 FXDWG front fender 34 degree frame with tank mount boss raised by ¾” New handlebar with FXDF risers/caps *Michelin®tires on all but FXDF and FXDWG FXDB rear wheel (black rim with chrome spokes) (17×4.5) (180- 60×17), rear tire pattern -GT502 (Screamin’Eagle®) FXDF exhaust pipes & mufflers with chrome exhaust shields Gloss black rear forging covers Current FXDB rear shocks with top covers Current FXDC battery cover with chrome Wide Glide®trim Forward foot controls New 2010 FXDWG Wide Glide® Domestic tail lights Canada & all International tail lights Taillight (HDI/Canada) Side mount license plate Domestic only •Internally wired handlebar •34 degree frame with tank mount boss raised by ¾”& rear forgings moved out 2mm each side from FXDF •Flame tank replacement part is VIN restricted •Two new rear fenders (Domestic & HDI/Canada)

Incoming search terms:

CRUISADER Motorcycle Laser-Radar Detector Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Installation of Laser-Radar Antenna 7 General Information The laser-radar antenna is water resistant and designed to be mounted on a motorcycle, snowmobile, etc. Radar signals will pass through non-metallic materials such as fiberglass and plastic, however, be sure not to mount the receiver behind any metal, as it will block the receiver’s antenna. This receiver also incorporates a laser detector. In order for the laser receiver to “see”, it can not be mounted behind any object. In some installations, this is not possible. We supplied an additional laser only receiver for this instance. If the installation allows for a clear view for laser-radar receiver, the extra laser receiver can be used for rear detection. Because the optimallocation for mounting the antenna varies by vehicle type, the hardware supplied is designed to offer a wide variety of mountingoptions. Note: The “antenna” is the bubble area on the case. All references to antenna in this manual will be thebubble area. Note: Use of hardware that is not supplied or DRILLING into the case will cause damage to the receiver and void the warranty. Antenna Mounting Brackets There are 3 ways in which to mount the laser-radar antenna; dual lock fastener, reflector bracket and universal brackets (similar to old car radio ground straps). These mounting accessories can be used on their own or in combination to provide the best mounting solution for the vehicle. Do not drill into the receiver housing! The reflector bracket serves two purposes; (1) to allow vertical mounting of the antenna (see page 10 for vertical install instructions) and (2); when mounted in reverse (angled portion towards the wires.) allow the receiver to be installed on any horizontal area.

Incoming search terms: