changing the spark plugs on an r1200rt

You search Auto repair manual PDF changing the spark plugs on an r1200rt, if there are search results will appear below. If search results do not exist, please search by others keyword.



  changing the spark plugs on an r1200rt Direct Download speed 5282 Kb/s

  changing the spark plugs on an r1200rt Full Version speed 6162 Kb/s



SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

HONDA CB650/ 750F/ 900F/ 1100F/ GL1100 Spark Unit Set Installation Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
INSTALLATION INSTRUCTIONS: 1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the seat and/or petrol tank to gain access to the original spark units (if fitted); these are normally fitted under the seat between the top frame tubing. Each of these units consists of a small alloy metal box with sleeved wires terminated by a small connector (coupler). They also have a mounting tab with a single fixing hole. 3. On four cylinder machines there will be two units, normally mounted back to back; one for cylinders 1&4 and one for cylinders 2&3. 4. For safety, disconnect the battery. 5. Unplug the couplers from each of the units. Undo the fixings and remove the units. 6. Fit the new spark units in the place of the old ones or find a suitable alternative, close to the connectors. Secure the units to the frame or mounting platform using the supplied tie-straps and adhesive mounting base (if required). If required, a thin sheet of rubber or double-sided tape can be used to keep the units in position. Do not completely wrap the units in foam rubber. 7. Push the wiring harness plugs into the new spark unit socket connectors; they will only fit one way. Reconnect the battery. 8. If you are rewiring the machine or do not have the standard wiring harness, the spark unit wire colours & functions are as follows: GREEN Ö GROUND (0 VOLTS) BLACK/WHITE Ö IGNITION SUPPLY (+12 VOLTS) VIA ENGINE STOP SWITCH YELLOW Ö IGNITION COIL OUTPUT (TO COIL —) WHITE Ö PULSE GENERATOR (WHITE RING) BLUE Ö PULSE GENERATOR (UNMARKED) There are two pulse generators, one for cylinders 1&4 and one for cylinders 2&3. The left hand one is normally for cylinders 1&4 (see fig.1). There are two wires of the same colour coming from each pulse generator, one of these wires is normally marked with a white band. The pulse generator wire with the white band connects to the white wire from the corresponding spark unit, the other pulse generator wire connects to the blue wire on the corresponding spark unit. If the white band is missing, this is normally the upper wire coming from the pulse generator. 9. Refit the seat and tank (if removed earlier). 10. Fitting is now complete, although for best results you may wish to verify the ignition timing, see the following guide

Incoming search terms:

HARLEY DAVIDSON GLOSS BLACK HEAD BOLT COVERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
This kit fits 1992 and later Evolution 1340 and XL models and 1999 and later Twin Cam-equipped models. INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Remove spark plugs. 2. See Figure 1. Install head bolt covers (1), on head bolts (3), secure using setscrew (2) and Allen wrench included with kit. To prevent setscrews from falling into the spark plug holes, start threading the setscrews into the covers before placing them over the head bolts. Position cover on head bolt so that when spark plug is reinstalled setscrew is hidden from view but accessible with Allen wrench. Do not tighten setscrews on high points of bolts. 3. Reinstall spark plugs. Tighten spark plugs to 11-18 ftlbs (15-24 Nm) . If a torque wrench is not available, finger- tighten spark plug and then, using a spark plug wrench, tighten plug an additional 1/4 turn. 4. Readjust setscrew tightness after motor has operated at full operating temperature and then cooled. 2 1 3 is 001586 1. Head bolt cover 2. Setscrew 3. Head bolt Figure 1. Head Bolt Cover Installation

Incoming search terms:

SANYANG HD 125/ 200 Specifications And SERVICE MANUAL

0

Filed Under (Sym) by admin on 24-11-2010

download
heck and adjustment Fault condition Probable causes Loosen carburetor drain bolt to check if there is gasoline inside the carburetor Fuel supplied tom carburetor sufficient No fuel is supplied to carburetor Remove spark plug, install it into spark plug cap, and perform a spark test against engine ground. Perform cylinder compression pressure test. Check if sparks Weak sparks, no spark at all Low compression pressure or no pressure Re-start by following the starting procedures No ignition There are some signs of ignition, nut engine can not be started Remove the spark plug again and check it. Remove carburetor after 30 minutes and connect a hose onto fuel rich circuit. Then blow the hose with air Dry spark plug Wet spark plug Blowing in normal Blowing clogged 1. No fuel in fuel tank 2. Check if the pipes, fuel tank to carburetor and intake vacuum, are clogged. 3. Float valve clogged 4. Lines in fuel tank evaporation system clogged 5. Malfunction of fuel pump 6. Loosen or damaged fuel pump vacuum hose 7. Fuel filter clogged 1. Malfunction of spark plug 2. Spark plug foul 3. Malfunction of CDI set 4. Malfunction of AC generator 5. Ignition coil is in open or short circuit 6. Ignition coil leads open or short circuit 7. Malfunction of main switch 1. Piston ring seized 2. Malfunction of cylinder valves 3. Worn cylinder and piston ring 4. Cylinder gasket leak 5. Sand hole in compression parts 1. Malfunction of throttle valve operation 2. Air sucked into intake manifold 3. Incorrect ignition timing 1. Fuel level in carburetor too high 2. Malfunction of throttle valve operation 3. Throttle valve opening too wid

KAWASAKI KX450F SPARK XCR SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Place the machine on a stable work stand. 2. If you are not familiar with removing the original exhaust refer to the owner’s manual before you start work. 3. Always allow your machine to cool down before attempting to remove the exhaust. 4. Remove the two bolts from the right side panel. Then remove the side panel. 5. Loosen the stock mid-pipe clamp, then remove the stand-off bolt and bracket bolt that supports the muffl er. 6. Remove stock muffl er and clamp from the stock head pipe. 7. Slightly loosen the stock head pipe at the cylinder head to aid in aligning the parts. INSTALLING THE NEW XCR SYSTEM 1. Installer must use supplied hardware. 2. Slide mid-pipe onto head pipe. Rotate the mid-pipe slightly to obtain proper alignment with sub-frame mount. 3. Install the supplied M8x16mm bolt through sub-frame into the stand-off mount on mid-pipe (Finger tight). 4. Slide the muffl er onto mid-pipe, align muffl er mount with the stock muffl er mount hole, and install and fi nger tighten the OEM bolt. 5. Once you have the system fully aligned, install and tighten all the bolts securely to factory specifi cations. 6. Replace the side panel and secure the mounting bolts. 7. Re-tighten stock head pipe at the cylinder head. TEST RIDING 1. When you fi rst ride the bike be aware that the characteristics are often quite different so start out slowly. TUNING 1. On the KX450F, we suggest using stock jetting based on our testing condition. These specifi cations should only be used as a guideline. Riding at different elevations or climates may require using different settings to obtain peak performance. If you need additional assistance, please refer to your Kawasaki owner’s manual. 2. To convert system from Offroad to Competition specifi cations, remove the 5mm Allen bolt and Spark arrestor. Two different Db lowering inserts are also available (see accessories section on page 2). To return the system to Offroad specifi cation re-install the Spark arrestor into the rear of the muffl er using a small amount of blue thread locking compound (Loctite® 243) re-tighten the 5mm Allen bolt (6.5 ft pounds)

Incoming search terms:

2007 KTM 250, 450, 505, SX-F QPX Performance Tip/ Spark Arrester Clean out Procedure

0

Filed Under (KTM) by admin on 24-01-2012

download
Step 1: Take off the end cap of exhaust by removing the five (5) screws using a T-20 torx wrench. Cut the silicone around stock end cap using a box knife, then pull cap straight off. Step 2: Step 3: To install your new QPX Performance Tip/Spark Arrester, slide QPX assembly into muffler with engraving on base right side up. Step 4: Align holes of QPX base and muffler, then reinstall the five (5) original screws with your T-20 torx wrench. Installation is now complete. Store instructions in a safe place for future reference. (See clean out instructions on reverse.) If the spark arrester screen isn’t already installed in the QPX Performance Tip, remove the four (4) M6 bolts attaching the cone to the base, remove cone, install screen between base and cone, reinstall M6 bolts and tighten. Do NOT tighten. Start, but leave loose until all screws are started, the tighten securely.

Incoming search terms:

CHANGING OIL IN THE KAWASAKI VULCAN VN 2000

0

Filed Under (Kawasaki) by admin on 16-12-2010

download
CHANGING OIL IN THE KAWASAKI VULCAN VN2000 ( based on a 2005 model) by tensm an1 Preparing the motorcycle: 1. To start, level the motorcycle – my preference is to put a spacer blocks under the kickstand on the left side of the motorcycle and under the frame on the right side of the bike just under the frame member. These blocks are made from scrap lumber. I find it is easier to set the right side block first as shown and tilt the motorcycle until the frame contacts the block, then, holding the handlebars, kick the left side block under the kickstand. 6″ NOTE: This dimension may not be correct for 2004 models as the 2005 models have a different kickstand – the 2004 model will likely be thicker. To be sure your blocks are the correct thickness the first time, lay a level across the luggage rack as shown. You may need to shim them slightly to hold the bike dead level. 2 7/8″”
Or, in the absence of a luggage rack, the seat will do: 2. Get the necessary tools ready: Oil filter wrench – I like the band type shown, but a metal strap type will work. 14 mm box wrench

Incoming search terms:

Aprilia Big Bore Kit 102mm Mounting And Installation instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
The installation takes place as usual. Change the cylinder and pistons. The engine must be brought in at least 500 Km!! Naturally the mapping must be adapted for this conversion! Use a Power Commander or a Rapid Bike Modul and adjust it correctly on a Dyno Stand. The compression ratio is as standard, 12,5:1, like a stock bike! Therefore it is not 100% necessary to change the spark plugs thermal value or the octan value. But if you use your bike for racing then you should go for different spark plugs (we use NGK DCPR9EVX spark plugs) and 98 octan fuel. For best performance use our Racing air filter system (models till my 2003 item # a123, a124, a125. For models up from my 2004 item # a121a). This systems increases the air flow which is a very good effect on all Aprilia models and particularly together with the Big Bore Kit

BMW R1200RT Sport/ Touring 1100X Kit Installation Manual

0

Filed Under (BMW) by admin on 17-12-2010

download
Step 1 — Locate ‘mold circle’ indentation on each side fairing panel (Pic 1). With panel mounted on bike, this indentation is center, at rear inside panel edge, and faces inside. Temporarily install bracket as shown in (Pic 2), align bottom bracket hole over indentation and mark for hole. Remove brackets at this time. Step 2 — Remove fairing body side panels. Four screws per side required for removal, see owners manual. Drill a 3/8″ hole at mark. If harness kit has not been installed, do not re-install left side panel until finished unless you remove tank to install harness. Removal of the tank is the best option to route harness from battery area to front of the bike. Step 3 — As required, re-install fairing body side panels. Do not re-install the top factory inner panel Torx Screw yet, as you will re-use this screw to secure the top light bracket mounting hole to the fairing panel. Step 4 — Using 10/32×1/2 screws and black shoulder washers from Hardware package, secure lights to PIAA Ezy-Mount® brackets (See Pics 3 & 4). Right side bracket is stamped ‘EZY-MOUNT’. See note below for Powersports lights. Due to close proximity of the light body to fairing side panel, access to the vertical adjustment screw on the panel side of the light will not be possible after installation. To prepare for this; before installing bracket/light assembly to panel, make sure this screw is tightened so that you can barely move the light body. After bracket is installed, final vertical adjustment can be secured with the inside screw. Torque on this screw is adequate to hold vertical adjustment, and the screw that faces the panel will not come loose. NOTE: WHEN INSTALLING POWERSPORTS LIGHTS, YOU MUST INSERT THE SHOULDER ADAPTER WASHER INTO THE LIGHT FOOT, BEFORE INSERTING SCREW TO SECURE LIGHT FOOT TO BRACKET. THIS ADAPTER CENTERS LIGHT FOOT OVER PEMNUT (TIGHTEN THIS SCREW SECURELY). Step 5 — Insert well nut into previously drilled 3/8″ hole. Place bracket assembly against fairing, aligning top hole with the top fairing mounting position; re-install the factory Torx screw at this location. Adjust as necessary and install the second supplied SS 10/32 x 5/8 Torx screw thru the lower bracket mounting hole to the well nut. With constant pressure on the screw, tighten securely. Constant pressure ensures that the rear expandable section of the well nut captures the back of the plastic inner panel as you tighten the screw. Future removal of fairing panels is now possible with light assembly installed (utilizing the bottom bracket mounting screw), thus re-alignment of lights is not required after normal maintenance.

how to Changing Oil and Filter BMW K75S

0

Filed Under (BMW) by admin on 26-10-2010

download
Put the bike on the centerstand and put a towel under the bike to keep the belly-pan from getting scratched. If you are lucky this is all you have to do; remove the two belly-pan screws and slide the belly-pan forward ever so slightly until it falls into your hands. However, this slightly more detailed method may be required. Remove the two socket head cap screws from the front of the pan. Loosen the two screws that hold the rear tang which in turn holds the rear of the belly- pan in place. The two screws up front face straight up, and will need to be removed by laying on your back with the business end of the allen wrench (5mm) pointing up into the air. The two in back are 8 mm, and also point straight up. Be careful to get the right ones: the two bolts that hold centerstand are near the bracket bolts, and their mistaken removal could leave you with a lap full of motorcycle. The two rear bracket bolts only need to be loosened to let the nose of the belly-pan drop enough to give you maneuvering room to remove it. With the two cap screws out of the front, slide the belly-pan forward and off the mounts. The tongue that engages the grommet at the front-top-center of the pan may not want to cooperate at first, and the pan itself may hit the lower fairing before the tongue disengages from the grommet. Wiggle it around and spring the pan enough to get it off the lower front mounts and it will drop off the top front mount on its own

Incoming search terms:

Incoming search terms: