china steel buyers from usa co ltd 163 com 126 com scam edu mail

You search Auto repair manual PDF china steel buyers from usa co ltd 163 com 126 com scam edu mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

PIAGGIO Power Program with SIP Stainless Steel Joint Pipe Installation Manual

0

Filed Under (Piaggio) by admin on 28-10-2010

download
First, loosen and remove both screws between joint pipe and exhaust. Then, remove the other two upper screws, as in illustration 2, between cylinder and joint pipe. This may be a little difficult to reach. For additional ease removing screws, raise up motor frame with a crowbar or chisel. Now, remove old joint pipe and replace with SIP stainless steel pipe. Don’t forget to replace old gaskets with new gaskets, included in delivery. Join us in the SIP Article Forum for further handy tips and tricks from those in the know at www.sip-scootershop.com Turn down screws bit by bit, one after another, to ensure balanced fit, making sure to loosen muffler screws shortly. If you should have difficulty getting a good fit, here’s a tip: drill longer holes on exhaust flange to get better adjustment. Finito; put away the tools and take a test drive

Incoming search terms:

Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

DUCATI EVOLUZIONE SLIPPER CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
If installing with Ducati OEM basket you need the washer cod. 0D1SR140C220045 (3mm). – If installing with STM basket (Z12 o Z48) you need the washer cod. 001MG019 (1,5mm). – Insert the correct washer on the gear shaft. – Perform the initial hub group assembly: position the progressive engagement steel plate (003MG015) on the hub (0F3SR140J24001C) , with the step facing up. Be careful to position it correctly into the specific seats, then check that pushing one side, the opposite stand up simultaneously. – Now put the 6 steel balls (001MG025) at the bottom of the grooves using a little bit of grease. Then fix the clutch drum (0F3SR140J24002C) on the clutch hub (0F3SR140J24001C) at rest position, using an M6 screw to help locking the two parts, avoiding in this way any possibility for the steel balls (001MG025) to fall out while inserting the hub pack on the main shaft. – Insert the hub pack on the gear shaft – Insert the clutch discs starting with the sintered one and finishing with the steel guided one; total disc set thickness must be included between 36 and 36,5mm. – Remove the M6 screw from the hub (0F3SR140J24001C). – Put the drum stopper hub (003MG106) on the hub (0F3SR140J24001C). – Verify that the secondary spring support (0F3SR540B140016) is well inserted into its housing on the drum (0F3SR140J24002C). – Insert the secondary spring (0S2085) into its housing on the drum (0F3SR140J24002C). – Mount the pressure plate (003MGP10) on the drum (0F3SR140J24002C) . – Position the Evoluzione spring (0S1090) on the pressure plate (003MGP10), with the convex part facing up (STM logo facing up), making sure previously that the squared section ring (901SE003), which works as primary spring support, is well positioned into the pressure plate itself. – Assemble the complete spring stopper pack: starting from the spring stopper plate (003MG008), with the shaped side facing up as shown in the picture. Insert the ball bearing (003MG007) and finally the spring stopper hub (0F3SR140N220007). Once completed these operations, position the complete spring stopper pack inside the Evoluzione spring (0S1090). – Insert the toothed washer (901RD101) with the convex side facing up, then insert and tighten up the clutch nut (0F30S140C220013); use a dynamometric wrench setting the torque suggested by the bike manufacturer. We suggest to use the specific optional tool (UTL-0020) in order to lock the pressure plate (003MGP10) while performing this operation. – Assemble the complete bearing rest pack: insert the washer (001MG018) in its housing on the bearing rest (0F3SR140N220004). Then put in the same housing the ball bearing and the push rod pin of the original clutch. – Position the complete bearing rest pack in the pressure plate (003MGP10), making sure it fits correctly into the housing grooves. – Manually practise a little pressure on the bearing rest (0F3SR140N220004) in order to release the seat for the tightness circlip (003MG018). – Fit correctly the above mentioned tightness circlip (003MG018). MAKE SURE that it adheres to all the groove perimeter. NB: Once completed the installation, repeatedly operate the clutch lever, checking that the pressure plate performs correctly the opening and closing movements. For a road use of the clutch you have to check clutch plates set every 2000 km. Please verify that the clutch plates set thickness is between 36,5mm and 35,0mm. If it is inferior to 35,0mm please replace a 1,5 steel plate with a 2 mm steel plate. For a racing use of the clutch we suggest to check the clutch plates set thickness frequently. GENERAL SAFETY REGULATIONS – In this sheet are reported the directions to perform correctly the clutch assembly operations. – STM reserves the right – without notice – to introduce any technical change whenever deemed it to be necessary to improve functionality and quality of the products. – Assembly operations must be performed by a skilled technician and must be scrupulously observed. – Before mounting the clutch make a complete inspection of the various parts, in order to verify the possible presence of faults or anomalies on the motorbike. – Make sure that there are no missing/damaged parts in the package . – Some parts of the clutch and its components can have sharp surface: handle with care. – Some components of the clutch, because of their small dimensions can be swallowed: keep away from children. STRADA srl Via Campo Archero 20 10023 Chieri ( TO ) Tel +39 011 9422832 Fax +39 011 9471447 003 MG 018 Tightness circlip

Incoming search terms:

TOYOTA Tacoma 2005 – STAINLESS STEEL EXHAUST TIP Procedure

0

Filed Under (Toyota Manuals) by admin on 18-10-2011

download
Safety (eye protection, rechecking torque procedure, etc.).  Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).  Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Installation. (a) Make sure the vehicle’s tail pipe is free from dirt and debris. (b) Remove exhaust tip from box and set on a soft surface to prevent scratching. (c) Slide the Stainless Steel clamp over the vehicle tailpipe as shown. (Fig 1-1 & 1-2) (1) Locate the bolt of the clamp on the right side (3:00 Position) with the nut on the top as shown. (Fig 1-1) (2) Continue sliding up out of the way so it won’t interfere when you install the exhaust tip and aluminum bushing. (Fig. 1-2) (d) Slide the exhaust tip over the tail pipe with the bump facing toward the rear of the vehicle as shown. (Fig 1-3) (1) If necessary, a rubber mallet may be used to aid installation

2007 Harley-Davidson Softail Family Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
frame Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Swingarm Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Front Fork 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers Rear Shocks Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Caliper Type 4-piston front and rear 4-piston front and rear 4-piston front and rear Rotor Type: (diameter x width) Patented, uniform expansion rotors Patented, uniform expansion rotors Patented, uniform expansion rotors Front 292 mm x 5.08 mm 292 mm x 5.08 mm 292 mm x 5.08 mm Rear 292 mm x 5.84 mm 292 mm x 5.84 mm 292 mm x 5.84 mm Front (mm) 130 130 130 Rear (mm) 109 109 109 Engine Torque (EU standard EC95/1)5 86 ft. lb / 117 Nm @ 3200 rpm 89 ft. lb / 120 Nm @ 3300 rpm 89 ft. lb / 120 Nm @ 3300 rpm Right 29° 30° 28° Left 26° 28° 26° Battery Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating ) Charging Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Starting 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement Headlamp Headlamp Headlamp Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Tail/Stop Lights Tail/Stop Lights Tail/Stop Lights 8W/28W (5W/21W) 8W/28W (5W/21W) 8W/28W (5W/21W) Turn Signal Lights Turn Signal Lights Turn Signal Lights 28W (21W) self-canceling 28W (21W) self-canceling 28W (21W) self-canceling Indicator Lamps Indicator Lamps Indicator Lamps High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6- speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings Passing Lamps Chrome Vivid Black Vivid Black Vivid Black Black Cherry Pearl Black Cherry Pearl Black Cherry Pearl Deep Cobalt Pearl Black Pearl Black Pearl Pewter Pearl Fire Red Pearl Deep Cobalt Pearl White Gold Pearl Deep Cobalt Pearl Olive Pearl & Vivid Black Suede Blue Pearl & Vivid Black Suede Blue Pearl White Gold Pearl & Vivid Black Black Cherry Pearl & Pewter Pearl Olive Pearl White Gold Pearl & Deep Cobalt Pearl Fire Red Pearl & Black Pearl Pacific Blue Pearl Deep Cobalt Pearl & Pewter Pearl Pewter Pearl Yellow Pearl White Gold Pearl

Incoming search terms:

Honda CBR 600 F4i 2004 – 2005 Bestem USA Fiberglass F13 Installation Guide

0

Filed Under (Honda) by admin on 20-11-2011

download
We highly recommend having a professional install this undertail. A dremel tool or nsimilar is what we found the best to cut plastics. Place bike on a rear wheel center stand. Remove passenger seat and hardware which secure stock undertail section Unplug the harness that connects tail light and remove the stock undertail. Position Bestem undertail close to the bike and determine the amount of plastic needs to be cut out. Use a dremel tool to carefully trim off plastics (glove boxes etc). This is the most time consuming part of the installation but your patience will be paid off. 5) Once the new undertail is slide in, determine holes need to be drilled (only on
certain models). Reuse the hardware for the stock undertail to secure the new undertail. 6) The wiring color codes from two round tail lights are Black Wire – Ground, connects to Ground wire. Red Wire – Brake Light, connects to brake light. Blue Wire – Running Light, connect directly to the running light. Orange Wire – Turn Signal, connect them to your L/R turn signal wires We highly suggest you solder the connections and use heat shrink wrap to seal the connections. Test your lights before going out for a ride, also make sure your new undertail is securely installed on the bike. Now it’s time to go out for a spin!

Incoming search terms:

Kawasaki KLX110-L Performance Exhaust System installation Manual

0

Filed Under (Kawasaki) by admin on 09-11-2010

download
With over 70 years combined experience in both racing and the development of four stroke exhausts systems, Two Brothers Racing announces the release of its new M-6 series exhaust system for the highly anticipated Kawasaki KLX110-L. Kawasaki’s KLX110-L delivers strong, controllable power and surprising acceleration. By adding a custom designed Two Brothers Racing performance exhaust system you will experience increased throttle response and more power in the critical areas of the powerband. Factory installed U.S. Forestry Service approved screen type spark arrestor included with our stainless/aluminum systems. Save weight, improve sound and gain power throughout the rev range with our race track proven stainless steel and aluminum exhaust system. Header Features: » Mandrel bent thinwall (0.35″ x 1.125″ stepped to 1.375″) stainless steel headpipe » CNC machined stainless steel headpipe collar » CNC machined aluminum headpipe flange (gold anodized) Muffler Features: » Thinwall extruded 6061 T-6 aluminum sleeve » TIG welded canister mount for easy installation and extreme durability » CNC machined inlet cap » 1.5″ x .035″ stainless steel perf core » High temperature packing material » CNC machined & threaded outlet end for easy repack » Removable die-cast magnesium M-6 outlet » USFS approved spark arrestor included (removable) » Optional sound reducing “Mini” MX P2 PowerTip™ (gold anodized) available, part # 005-P2 » Made, tested & assembled in Santa Ana, CA USA

Incoming search terms: