classic motorcycles ratings 1980 cb 750 f

You search Auto repair manual PDF classic motorcycles ratings 1980 cb 750 f, if there are search results will appear below. If search results do not exist, please search by others keyword.



  classic motorcycles ratings 1980 cb 750 f Direct Download speed 5282 Kb/s

  classic motorcycles ratings 1980 cb 750 f Full Version speed 6162 Kb/s



2002 URAL Classic Motorcycles BC-75 (Bavarian Classic) LC-75 (Luxury Cruiser) Tourist, Adirondac & Patro Owner's Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Front brake control lever (Fig.1, #5). When the lever is squeezed, the front wheel brake is actuated. The front brake should be used together with rear brake. When the brake lever is squeezed, the stop signal lamps are switched on. Kick lever (Fig.1, #11) is designed to start the engine. On pressing the lever the crankshaft of the engine is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Note: this is a backup to the electric starter. Gear shift foot pedal (Fig.1, #12) is a two-arm type. When the front arm is pressed, shifting from high to lower gears takes place. When the rear arm is pressed, shifting from low to higher gears takes place. Since the heel-toe shift lever is short-coupled, you will find it easier to shift up if you rotate the heel of your left foot in towards the rear arm before stepping on it with your heel. The neutral position is fixed between the I and II gears. Speedometer is on the dash board, with trip (Note..BC-75 has no trip odometer) and total odometer. The trip odometer is reset to zero by rotating push-button (Fig.1, # 3) counterclockwise. Note that the odometer reads in kilometers not miles. Ignition Switch (Fig.1, # 19) has three fixed positions of the key. The position and switching diagram of the ignition locks are shown above.
18 The indicator lamps are mounted on the instrument board: (Fig. 1, # 2) — turn indicator pilot lamp, (orange) (Fig. 1, # 4) — gearbox neutral and reverse gear engagement, (green) (Fig. 1, # 18) — head lamp high beam indicator, (dark blue) (Fig. 1, # 20) — alternator fault indicator lamp, (red) Note: If the red alternator fault light stays on continuously during normal operation above approximately 1500 RPM, there is a problem with the charging system or battery. Throttle Control (Fig.1, # 6) is on the right handlebar. Turning the twist grip counterclockwise increases engine speed. Ignition Cutoff Switch (Fig.1, # 7) has two positions, ignition off (up), and ignition on (down). Low and High Beam Light Switch (Fig.1, # 15), turn indicator switch (Fig.1, #13) and horn push-button (Fig.1, # 14) are combined in one unit on the left-hand handle bar control housing. Master Battery Switch (Fig.1, # 21) is under the seat. Electric Start Button (Fig. 1, # 8) is located on the right-hand twist grip, below the kill switch. The Steering Damper absorbs lateral kicks on the front wheel. Turning tightening bolt (Fig.1, # 17) clockwise increases friction. This can be used while riding over bad roads

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

SUZUKI MOTORCYCLES Gsxr 600, Gsxr 750, Gsxr 1000 teak the lead

0

Filed Under (Suzuki) by admin on 12-11-2010

download
The launch of the sixth generation of Gsxr marked a shift in Suzuki’s emphasis on two fronts. One, the Gsxr 1000 now took the upper hand in the development stakes. Historically, the Gsxr 750 led the march-arriving first, gaining the most recent technology, absorbing the lion’s share of corporate pride-but by 2003 the Gsxr 1000 was in the lead. Two, the Gsxr 1000 represents another, more subtle shift for Suzuki engineering, in which the designers-the lucky guys who get to clothe these amazing machines-have more freedom of expression. With this generation, the designs turned edgier, sharper, more aggressive looking than ever. What’s more, the Gsxr 1000 K3 would be the proving ground for a host of changes brought to the Gsxr 600 and Gsxr 750 for 2004. In fact, nearly every upgrade to the smaller bikes appeared on the Gsxr 1000 a year before. But the real impetus for driving the Gsxr 1000 to the head of development and, indeed, shortening its development cycle was competition both on the track and in the showroom. For the track, it was understood that Superbike racing would revert to allowing 1000 cc four-cylinder bikes in place of the 750s that had been the limit since 1982. In 2002, Yoshimura and Mat Mladin barely lost the AMA Superbike crown to Nicky Hayden aboard the Honda RC5!. But it would be the RC’s swan song of competitiveness with the change to 1000 cc fours. To keep speeds in check, the AMA Superbike rules would require 1000 cc fours to have some additional limitations compared to the twins and triples. For example, “Cylinder heads may be ported and machined, but altering of valve angles will not be permitted; aftermarket valves, springs, retainers, and other valve-train components will be permitted; valves must be stock size and same basic material as original equipment; aftermarket camshafts will be permitted, but earn lift and resulting valve lift must be no greater than stock. “In addition, the “stock crankshaft must be retained, The only allowable modifications are balancing, polishing of bearing surfaces and attachment of accessory drives. Homologated transmission gear sets (one optional set of ratios per approved model) will be permitted. Optional sets will be price-controlled and must be available to any legitimate AMA Superbike competitor. Homologated fuel-injection throttle-body assemblies (one optional type per approved model) and aftermarket airboxes will be permitted. Modifications to throttle bodies will not be permitted. Optional throttle bodies will be price-controlled and must be available to any legitimate AMA Superbike competitor.” The thinking was simple: keep the liter bikes from sucking through massive throttle bodies, and the horsepower might not (and, it was hoped, would not) go through the roof. In preparation for racing, Suzuki moto wanted to make a host of small changes to the Gsxr 1000, but its motivation was also to keep the bike at the forefront of open-class street bikes. Suzuki engineers knew that Honda and Kawasaki were readying all-new models-the CBR 954 RR and the ZX 9 R had long since been vanquished-and rumor had it that Yamaha was ready with yet another push with the R1.It was the right time to make alterations to the Gsxr 1000. Heading the list was, as one might expect, a revised engine.

Incoming search terms:

HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

victory 650 And 750 twIns specification

0

Filed Under (Victory) by admin on 13-11-2010

download
Super Sport. The example tested by Cycle World magazine in August 1968 looked identical to the European specification 750 except for higher handlebars, a 35/35 watt headlight, larger round CEV taillight, 120mph Smiths speedometer, and an American Eagle tank badge. The headlamp shell was also different, with an additional warning lamp, and the American Eagle headlight shell featured the large hole and rubber plug (with Laverda logo) as on some early 650s. When tested by Cycle magazine in January 1969 (now called the American Eagle ‘Classic’) there was a different colour scheme, with pinstriping on the fuel tank and sidecovers (although this colour scheme also appeared in some Italian advertising and official photos). Optional for the American Eagle was a large chrome-plated engine protection bar with chrome Vitaloni rear vision mirrors attached on each side. In McCormack’s advertising the bore and stroke of the American Eagle were listed as 79.5 x 76.2mm, and this was obviously incorrect as the engine specifications were the same as the European versions. The claimed power by McCormack for the American Eagle was also Below: This Super Sport, number 1646, is based on a 750 GT, but others were converted 750 Ss. ** t he l AverdA t wIns & t rIples B IBle top triple clamp from the top. A round reflector was situated on the headlamp mounts. As there was no room for all the wiring inside this smaller shell, the electrical connectors were moved underneath the fuel tank, and there were thick grey wires leading to the Lucas switches. When turn signals were fitted these were also Lucas, the handlebar switch being on the right. The throttle was now a chrome-plated, dual-cable Tommaselli Daytona 2C, without a throttle stop, with the handlebar also Tommaselli. The dual seat on a fibreglass base, or solo seat with locking compartment, continued as before. The 750 SF1 continued to be sold in the UK, where the price was £998, but at that time a 750cc Triumph Bonneville T140V sold for £625 so the Laverda was never going to be a volume seller. In Italy, the SF1 was still one of the most popular large capacity machines available, selling for L1,227,200 when the Triumph T140V sold for L1,357,000

URAL Classic Motorcycles SPECIFICATIONS And Owner's Manual

0

Filed Under (Ural) by admin on 11-11-2010

download
Maximum speed of motorcycle 108 km/h 65mph 119 km/h 70 mph Reference fuel consumption at 85% of 12.5 km/L 29 mpg 14 km/L 32.5 mpg maximum speed Dry mass of motorcycle 700 lb 680 lb. Maximum load-carrying capacity 500 lb. / 485 lb. 400 lb. Noise level below 80db OVERALL DIMENSIONS Length 2500 mm / 8 ft Width 1700 mm / 5 ft 6 in Height 1100 mm / 3 ft 6 in Road Clearance 125 mm / 5 in Seat height 840 mm / 33 in Wheel base 1470 mm / 58 in ENGINE Type 4 stroke, overhead valves, opposed twin-cylinder Displacement 649 cc Cylinder bore 78 mm Piston stroke 68 mm Compression ratio 9.1:1 Rated horsepower 25.8 KW / 35 Hp Rated rotational speed 5600 RPM Rated torque, Nm 45 Nm / 33.2 ft.-lbs. Lubrication system Dual system of forced lubrication and by splashing Lubricant SAE 20W/50 CARBURETOR Carburetor type 32 CVK Keihin Number of carburetors 2 Air cleaner K & N Air filter Fuel 91 octane premium unleaded gasoline PCV Valve Internal Breather
12 ELECTRICAL Ignition system (CDI) Ignition coil 135.AC.B Spark plugs NGK BP7HVX / or equivalent Ignition timing Automatic spark timer Alternator 35 amp / 12 Volt Battery Interstate #YTX20L-BS or equivalent Headlight Sylvania Halogen 6024, 7″ round sealed beam TRANSMISSION Clutch Dry double-disk clutch Gearbox 4 speed gearbox with reverse gear lever GEAR RATIOS I gear 3.6 II gear 2.28 III gear 1.7 IV gear 1.3 Reverse gear 4.2 Speedometer drive ratio 0.4 Deco & BC-65 0.5 Final drive ratio 4.62 FLUID CAPACITIES Tourist, Bavarian Patrol & Deco Fuel tank 5 Gal / 19L 5 Gal / 19L Reserve .5 Gal / 2L .5 Gal / 2L Engine 76 oz / 2.25L 76oz / 2.25 L Transmission 34 oz / 1 L 34oz / 1 L Final drive 3.5 oz / 105 ml 4.5 oz / 135 ml Telescopic Forks N/A on Tourist N/A on Patrol (LC-75 & Deco) 135ml / 4.5 oz Shock Absorbers 105 ml / 3.5 oz 105ml / 3.5 oz

Incoming search terms:

2001 URAL Classic Motorcycles Owner's Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Front brake control lever (Fig.1, #5). When the lever is squeezed, the front wheel brake is actuated. The front brake should be used together with rear brake. When the brake lever is squeezed, the stop signal lamps are switched on. Kick lever (Fig.1, #11) is designed to start the engine. On pressing the lever the crankshaft of the engine is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Note: this is a backup to the electric starter. Gear shift foot pedal (Fig.1, #12) is a two-arm type. When the front arm is pressed, shifting from high to lower gears takes place. When the rear arm is pressed, shifting from low to higher gears takes place. Since the heel-toe shift lever is short-coupled, you will find it easier to shift up if you rotate the heel of your left foot in towards the rear arm before stepping on it with your heel. The neutral position is fixed between the I and II gears. Throttle Control (Fig.1, # 6) is on the right handlebar. Turning the twist grip counterclockwise increases engine speed. Engine cutoff switch (Fig.1, # 7) has two positions, ignition off (up), and ignition on (down). Low and high beam light switch (Fig.1, # 15), turn indicator switch (Fig.1, #13) and horn push-button (Fig.1, # 14) are combined in one unit on the left-hand handle bar control housing. Master battery switch (Fig.1, # 21) is under the seat. Electric Start Button (Fig. 1, # 8) is located on the right-hand twist grip, below the kill switch. The steering damper absorbs lateral kicks on the front wheel. Turning tightening bolt (Fig.1, # 17) clockwise increases friction. This can be used while riding over bad roads. WARNING: DO NOT TIGHTEN THE DAMPER TO THE POINT WHERE THE STEERING BECOMES STIFF . DOING SO WILL ADVERSELY AFFECT HANDLING QUALITIES . Parking brake (Fig. 1, # 22) is located on the right side of the motorcycle next to the foot peg. It is engaged by applying the foot brake pedal fully and turning the handle and pushing it down to hold the foot brake lever in the applied position. Always disengage the parking brake before moving the motorcycle

2004+ Victory motorcycles PGR-1000 SERIES Programmable Gear Readout Installation

0

Filed Under (Victory) by admin on 31-10-2010

download
1. Turn the key on and make sure the transmission is in neutral and ‘n’ is displayed on the readout. (Please leave the key ‘ON’ for about 5 seconds before continuing) 2. Turn the key off (.1 seconds) and then back on (1 second) again rapidly. The display should show 1 bar. If you wait too long before continuing the readout will exit the setup routine. (If the unit has already been cleared, it will immediately jump to step 6.) 3. Repeat step #2. The display should show 2 bars. 4. Repeat step #2. The display should show 3 bars. 5. Repeat step #2. The display should show 2 bars. 6. Repeat step #2. The display should show ‘n’ with a bar over it. If the display is upside down then kick the transmission out of neutral and the display will invert and show ‘C’. Tach adapter(for open-collector tach signal from ECM w/out pull-up resistor) ( 2004+ Victory motorcycles use this option , most other bikes use application on front page) VSS Notes: The PGR-1000 is designed for motorcycles with an Electronic VSS signal. Most modern motorcycles use a 3-wire hall-effect type speed sensor in the transmission with a power, ground, and a signal wire. The SEN-1019 is available for motorcycles without a factory VSS signal, fabrication will be required for sensor mounting

SUZUKI Hayabusa, GSXR 1000, GSXR 750, GSXR 600 Sport Brake Lever INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 21-02-2012

download
Before you install your new ASV brake lever, you MUST choose the correct brake light switch tab to install. You will find in the package with this lever one plastic bag with four smaller bags inside of it. One bag has two small phillips screws. The other three bags have small black aluminum blocks (light switch tabs) with labels on them. Part# BRC511-H is ONLY for HONDA motorcycles. Part# BRC511-STK is for all SUZUKI, TRIUMPH and 05-06 KAWASAKI ZX636R motorcycles ONLY. Part# BRC511-K is for all KAWASAKI motorcycles EXCEPT the 05-06 ZX636R . Choose the correct tab for your bike and install it onto the lever as shown in photo 2b using the two small Phillips head screws provided. It is recommended that you use locktite or another type of thread locking adhesive to make sure these screws do not come loose. Be sure to tighten these screws as tight as you can without stripping them. The brake stop / light tab is required for your ASV brake lever to work properly Carefully place the lever into the master cylinder while inserting the plunger rod into the barrel hole as shown in photo 4. Install the main pivot bolt, and tighten it until it is snug against the master cylinder. Do not over-tighten, as it could cause the lever to bind in the master cylinder