cleaning harley caliper on bike

You search Auto repair manual PDF cleaning harley caliper on bike, if there are search results will appear below. If search results do not exist, please search by others keyword.





Harley-Davidson CHROME FRONT BRAKE CALIPER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
See Figure 1. Refer to FRONT BRAKE CALIPERS: REMOVAL in the Service Manual, and follow the instructions to: a. remove the banjo bolt with bleeder valve (2) and both gaskets (4), and b. detach the front brake line (3) from the caliper. c. Discard the gaskets. For this installation, the banjo bolt (2) can also be discarded. d. Remove the caliper mounting bolts (1). Lift the brake caliper assembly upward to remove it from the brake disc. -J03529 1 of 4
2 5 3 4 1 is04104 1. Mounting bolt (2) 2. Banjo bolt with bleeder valve 3. Brake line 4. Gasket (2) 5. Screen cover Figure 1. Remove Existing Caliper 2. Remove the brake pads from the caliper. Refer to BRAKE PADS AND DISCS: BRAKE PAD REPLACEMENT, FRONT BRAKE CALIPER in the Service Manual. a. Remove the screen cover (5) from the caliper. b. See Figure 2. Note the orientation of the brake pads, and remove the retaining clip (2), pad pin (1) and brake pads from the caliper. Also note the position of the brake pads at removal, so they can be installed back in the same location. 3. Repeat the procedure for the opposite-side caliper. 2 1 is04105 1. Pad pin 2. Retaining clip Figure 2. Front Caliper Pad Pin Pad and Pin Inspection 1. Refer to BRAKE PADS AND DISCS: INSPECTION in the Service Manual, and follow the instructions given to inspect the brake pads. If any front brake pad is worn to 0.5 mm (0.020 inch) or less above the backing plate, replace all four front pads. 2. Inspect the brake disc thickness, lateral runout and warpage. If necessary, follow the instructions in the Service Manual under FRONT WHEEL to replace the discs. Chrome Caliper Installation 1. See Figure 3. Obtain the correct-side new chrome caliper assembly from the kit. Remove the screen cover (5), retaining clip and pad pin (4) from the caliper. NOTE Do not remove the shipping plug protecting the brake line threaded hole until ready to install the brake line. 2. Place the caliper over the brake disc with the brake line threaded hole (protected by a shipping plug) facing upward. 3. See Figure 1. Obtain two of the brake caliper mounting bolts (1), removed earlier. Loosely install both bolts through the front fork and into the chrome caliper. Alternately tighten the mounting bolts to 38.0-51.5 Nm (28-38 ft-lbs) . 4. Install the brake pads removed earlier or, if necessary, new brake pads into the caliper. 5. See Figure 2. Install the new pad pin (1) through the inner and outer brake pads. Tighten to 8.5-11.5 Nm (75-100 in- lbs ) . 6. Install the new retaining clip (2) onto the pad pin. NOTE Ensure that the screen cover is oriented with the single tab end up, and the double tab end down. 7. See Figure 1. Install the new screen cover (5) onto the caliper.

Incoming search terms:

Harley-Davidson The WHEELDOCK EZ-UP Center Stand Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common questions: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter

Incoming search terms:

Harley-Davidson touring bikes WHEELDOCK EZ-UP Center Stand Installation Instructions

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common problems: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter.

Incoming search terms:

Harley Davidson Sportster 4 Piston Rear Brake Caliper installation Manual

0

Filed Under (Harley Davidson) by admin on 02-04-2012

download
Installing Rear Caliper – Sportster Models Removing The Stock Brakes SPORTSTER REAR BRAKE SYSTEM 84 & UP MODELS The basic steps are the same to install a PM rear brake caliper kit on any of the late model Harley Davidson “swingarm” style motorcycles; all require the removal of the rear wheel. Using a suitable lift, raise the motorcycle high enough off the ground to allow you to remove the rear wheel assembly. PHOTO 2 W a r n i n g Center the motorcycle on the lift so that it will not fall while you are working on it. Photo 2: Remove the rear brake caliper assembly by unscrewing the 2 caliper mounting bolts that go through the caliper into the caliper mounting bracket. Lift the caliper up and off the mounting bracket and brake rotor, move the caliper back out of your working area. Don’t remove the brake line from the caliper yet; you will do this just before you are ready to hook it up to the new caliper. The brake pads are held into the caliper mounting bracket by 2 spring clips; slide the brake pads out of the mounting bracket and remove the retaining springs. PHOTO 3 Remove Cotter pin and rear axle nut, slide rear axle completely out. Photo 3: Remove nut from Right rear shock and rotate belt guard up. Slide belt off of pulley and roll rear wheel back 6 – 8″. Photo 4: Remove original caliper bracket from swingarm

Incoming search terms:

HARLEY DAVIDSON REAR BRAKE CALIPER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Prepare the Motorcycle for Service To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Follow the Service Manual instructions to disconnect the negative (-) battery cable. Remove Rear Brake Caliper Remove the Brake Pads 1. For models equipped with saddlebags: Remove the right-side saddlebag. Refer to the SADDLEBAGS section of the Service Manual. 2. Remove the rear master cylinder reservoir cover. 3. Pry both the inside and outside pads away from the brake disc and toward the caliper assembly to push the caliper pistons back into their bores. Use steady pressure to prevent scoring the brake disc. Pry between the pads and the brake disc. 4. When the pistons are fully retracted into their bores, pull the pad pins out to allow the pads to drop from the caliper assembly. Note the pads’ original orientation for installa- tion. 5. Install the cover on the rear master cylinder reservoir. NOTE Place a container under the brake caliper to catch brake fluid released when removing the brake line from the caliper. 6. Remove the banjo bolt fastening the rear brake line to the stock rear brake caliper. Save the banjo bolt for brake caliper installation and discard the two steel/rubber gas- kets. Remove the Stock Rear Brake Caliper 1. Apply isopropyl alcohol to the rubber bumper on the brake caliper to ease removal. 2. Lift the stock rear brake caliper toward the front of the motorcycle. The notch in the caliper must clear the weldment on the swing arm. 3. Remove the caliper from anchor weldment on rear swingarm. Inspect Pad and Pins 1. Inspect the brake pads. If friction material above the backing plate on either pad is 0.040 in. (1.02 mm) thick or less, replace the set. Follow the instructions in the Service Manual. 2. Inspect pad pins for wear and grooving. If wear is more than 0.015 in. (0.38 mm), replace both pins. 3. Inspect the brake disc and, if necessary, follow the instructions in the Service Manual to replace the brake disc. Install the Rear Brake Caliper NOTE Pay close attention to all warnings, cautions, and torque specifications in this instruction sheet and in the service manual when installing this rear brake caliper. NOTE Apply isopropyl alcohol to the rubber bumper for ease of installation. 1. See Figure 1. Position the caliper (1) between the brake disc and the rear fork. The weldment on the fork should fit between the notch and rubber bumper on the caliper. Verify that the full length of the rubber bumper contacts the underside of the weldment

Incoming search terms:

HARLEY DAVIDSON VRSC CHROME BRAKE CALIPER INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
This kit fits 2006 and later VRSC model motorcycles.INSTALLATION 1. See Figure 1. Press in the upper tab (3) with a small screwdriver and remove the stock brake caliper insert (1) from the brake caliper (2). NOTE When installing the front caliper insert, position the single prong tab to the top of the caliper. When installing the rear caliper insert, position the single prong tap toward the front of the caliper. 2. Install the the chrome brake caliper insert into the brake caliper with the caliper oriented in the same manner as the stock insert. 1 2 3 is00627 1. Brake caliper insert 2. Brake caliper 3. Single prong tab Figure 1. Front Brake Caliper (VRSCR Model Shown

Incoming search terms:

HARLEY DAVIDSON REAR THUNDERSTAR WHEELS INSTALLATION, MAINTENANCE AND CLEANING

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to the service manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from a Harley-Davidson dealer. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to the service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to the service manual. NOTES Install the primary bearing first, following the instructions in the service manual and using the WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle, and stock spacers to motorcycle. Refer to the service manual. MAINTENANCE AND CLEANING NOTE This wheel assembly includes plugs that have been installed in the openings between the brake disc mounting holes on one side of the wheel and in the compensator bowl of the 16×5 inch wheel. Missing or damaged plugs can be replaced using Wheel Plug Kit (44459-04) or individual plug (43871-09 – 16×5 inch wheel). Chrome parts must be maintained regularly so they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

HARLEY DAVIDSON CHROME CALIPER AND ROTOR COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents There are no service parts available for this kit. INSTALLATION Left Side Installation 1. See Figure 2. Assemble the wedge spacer halves (1 and 2) to the left lower caliper mounting bracket (3) with the screw (4) and washer (5). 2. See Figure 3. Install the left lower caliper mounting bracket (1) to the left fork slider by sliding the wedge spacer into the hole in the bottom of the fork slider. Tighten finger- tight. 6 3 5 3 3 4 2 1 9 8 7 3 is06000 1. Rotor cover top mounting bracket 2. Spacer (models without fender rails only) 3. Screw (16) 4. Caliper cover 5. Wedge spacer 6. Screw and flat washer 7. Lower mounting bracket 8. Caliper/rotor cover mounting bracket 9. Caliper mounting bracket Figure 1. Caliper and Rotor Cover Kit (Left Side Shown)

Harley-Davidson FL Caliper Mount Installation Manual

0

Filed Under (Harley Davidson) by admin on 26-02-2012

download
Motolight® Caliper mounts are designed to be mounted on the brake caliper mounting boss. Before removing the caliper bolt make certain you have the manufacturer’s recommended torque settings for your make, model and year. 2 . Disconnect your battery. Never work on the electrical system of a motorcycle while the battery is connected. If you’re not sure how, check your owner’s manual, or consider having your dealer install the lights. 3 . Motolights®, like any light, get hot when operating. Do not touch any part of the housing when the Motolights® are in operation and for at least 15 minutes after they have been turned off. 4 . If you are transferring your Motolights® to another bike or have obtained the lights secondhand, it is VERY IMPORTANT that you contact us at 800-567-8346 or 513-474-7530 for new caliper bolts of proper grade and size. Step 1. Unpack the Motolight® system . Take this chance to familiarize yourself with everything. Below is the list of included items: Item # Quantity Description 1 (2) º” x 20 x 5/8″ stainless steel socket head cap screws 2 (2) Housings, aluminum, assembled with lens, lamp and leads 3 (2) Mounting blocks, aluminum, left and right 4 (2) Caliper replacement bolts 5 (2) Lock washers 6 (1) Motolight wiring harness with relay and 20 amp fuse 7 incl. Special Harley auxiliary plug connector in wiring harness (included) 8 (2) Motolight decals (1 helmet size, 1 regular) 9 (1) Aiming tube (cardboard ring) 10 (1) 3/16″ hex wrench 11 (1) Pin wrench (for standard lamp retaining rings-not required for knurled/grooved rings) 12 (15) Cable ties, long and short

Incoming search terms: