clutch adjustment harley davidson 1999 flstf

You search Auto repair manual PDF clutch adjustment harley davidson 1999 flstf, if there are search results will appear below. If search results do not exist, please search by others keyword.



  clutch adjustment harley davidson 1999 flstf Direct Download speed 5282 Kb/s

  clutch adjustment harley davidson 1999 flstf Full Version speed 6162 Kb/s



HARLEY DAVIDSON DIAMONDBACK "LE" CHROME SERIES CLUTCH CABLE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.

Incoming search terms:

REKLUSE MOTOR SPORTS Pro Start Clutch Harley-Davidson OWNER'S MANUAL

0

Filed Under (Harley Davidson) by admin on 24-11-2010

download
REAK-IN PERIOD The ProStart clutch requires a short break-in period. During the break-in period, the ProStart should not be operated at steady engine speeds above 3000 RPMs for more than 10 minutes. Breaking-in the ProStart clutch equires start and stop cycles. Riding the ProStart clutch in stop-and-go city traffic for one hour will provide sufficient break-in. If you would like to accelerate the break-in period, find an empty parking lot with ample room and no other traffic. From a stop, bring the motorcycle to 20 miles per hour and then back to a stop. Repeat this process at least 20 times. MAINTENANCE Proper maintenance is important to ensure the longevity of the Rekluse ProStart clutch and the rest of the stock clutch components in your Harley- Davidson Motorcycle. Refer to your owner’s manual for proper primary chaincase oil levels and oil type. Rekluse recommends the use of Harley- Davidson Primary Chaincase lubricant with the Rekluse ProStart clutch. Do not use oils designed for use as automotive engine oil in your Primary Chaincase. If Harley-Davidson Primary Chaincase lubricant is not readily available, a premium-quality Diesel engine oil, such as Shell Rotella T, that does not contain friction modifiers may be substituted. Inspection and adjustment of the Rekluse ProStart clutch should only be performed by a service center trained in Harley-Davidson and Rekluse ProStart repair and maintenance. The Rekluse ProStart clutch should be inspected for adjustment after 1,000 miles of operation. Thereafter, inspection for adjustment should be performed at 5,000 mile intervals

Incoming search terms:

HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

Harley Davidson Five Speed Transmissions Hydraulic Clutch Modification

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Hydraulic Clutch Modification for Harley Davidson With Champion Reverse Gear 1 1.1 Install Reverse Gear Assembly to gearbox. 1.2 Remove clutch cover (left side). 1.3 Remove Release Plate (clutch adjustment) and Push Rods. 1.4 Install Hydraulic Clutch Release Cover with supplied spacer and two gaskets. 1.5 Bleed clutch system. NOTE: When bleeding clutch system, lever feel will become hard, do not force lever because piston is at end of travel.(Continue Bleeding) 2 2.1 Install Push Rod. 2.2 Push the rod into clutch assembly to force hydraulic piston to its start position. Push the rod hard until the clutch cylinder is fully compressed. This is the start position. 2.3 Install Hydraulic Clutch Throw-Out Bearing Holder and bearing to push rod. Do not install circlip at this time. 2.4 If the throw-out bearing holder does not fully seat into the Pressure Plate (Figure 2.4), proceed to step 2.5. If shaft is too short then use throw-out bearing holder from Champion Reverse Gear Kit, skip next step and proceed to 3.0 2.5 Measure distance between bearing holder and pressure plate (ensure that push rod is pushed in) Figure 2.4 2.6 Remove bearing holder and push rod, reinstall bearing holder until seated (without push rod). Measure distance from pressure plate to bearing holder. Figure 2.6 2.7 Add measurements taken in steps 2.5 and 2.6 2.8 Add 0.090″ to total of step 2.7 (allowance for clutch plate wear). Measurement should be approximately 1/8″. 2.9 Measure push rod length. 2.10 Subtract measurement of step 2.8 from measurement of step 2.9 (push rod length). This measurement represents the amount of material to be removed from ball end of push rod. (Step 2.11)

Incoming search terms:

2008 Honda CBR1000RR Clutch Inner Installation PROCEDURE

0

Filed Under (Honda) by admin on 23-04-2011

download
Refer to the 2008 CBR1000RR Service Manual for specific removal instructions. While completing this procedure, be careful not to damage the covers, cowls, or any other components. 1. Remove the air intake cover (page 3-8). 2. Remove the upper inner cover (page 3-9). 3. Remove the lower cowl (page 3-9). 4. Remove the right middle cowl (page 3-10). 5. Remove the right crankcase cover (page 10-5). Clutch Removal (page 10-7) 6. Remove the starter idle gear and shaft. 7. Remove the snap ring and stopper ring. 8. Remove the clutch lifter piece and plate. 9. Unstake the clutch center lock nut. Be careful not to damage the mainshaft threads. 10. Hold the pressure plate with the special tool. You must use the special tool (Clutch Holder, T/N 070MB-MFLA100) when removing the lock nut. Using an impact wrench will damage the main shaft threads. Clutch Holder: 070MB-MFLA100 (autoshipped in May 2008) 11. Remove the clutch center lock nut and washer and discard the lock nut as shown on top of page 3 12. Remove the clutch spring holder, spring seat, and two clutch springs. 13. Remove the spring seat. 14. Remove the following: • Pressure plate
• Spring seat • Judder spring • Clutch disc A • Clutch plate A • Seven clutch discs B • Clutch disc C  Clutch center NOTE: Do not remove the clutch outer. New Clutch Installation (page 10-20) NOTE: The new clutch disc assembly has a dif- ferent order of plates than the illustration shown in the Service Manual. Keep note of this when repairing updated units.
15. Install the new clutch disc assembly with- out removing the setting bolts. Rotate the main shaft to align the clutch disc assem- bly with the main shaft spline. 16. Slightly loosen the setting bolts. 17. Rotate clutch disc C to align its tabs into clutch outer shallow slots, then fully install the clutch disc assembly. 18. Remove and discard the setting bolts. 19. Install the spring seat

Incoming search terms:

HARLEY DAVIDSON HANDLEBAR RESERVOIR COVER SET INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
Kit 46098-98 fits the following models with single-disc front brake. •1996 through 2003 XL (Sportster®) models •1996 and later Dyna models •1996 and later Softail® models Kit 46099-98 fits the following models with dual-disc front brake. •1996 through 2003 XL (Sportster) models •1996 and later Dyna models •1996 and later Softail models •1996 and later FL Touring models INSTALLATION Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) NOTE Make sure you are using the correct retaining-ring pliers. Verify that tips of pliers are not excessively worn or damaged. 1. Adjust the clutch cable for maximum free play. With snap ring pliers, remove and retain the external snap ring from the bottom of the clutch lever pivot pin. Remove the pivot pin, clutch lever, clutch cable and rear-view mirror from the clutch bracket. NOTE Apply anti-seize (10) (Harley-Davidson part number 98960-97) from the kit to all screw threads prior to installation. 2. See Figure 1. Install the new chrome clutch bracket (1) using a clamp half (2), washers (3) and screws (4) from the kit. Tighten the screws to 70-80 in-lbs (7.9-9.0 Nm). -J01271 1 is01004 Figure 2. Clutch Cable Adjustment 3. Re-install the clutch cable and clutch lever, mirror and pivot pin and snap ring. See Figure 2. Re-adjust the clutch cable so there is a 1/16-1/8 inch (1.6-3.1 mm) gap between the clutch cable ferrule and the end of the clutch bracket (1). 4. Remove the original clamp half from the front brake master cylinder assembly. 5. See Figure 1. Install the new chrome clamp half (2) on the front brake master cylinder assembly using washers (3) and screws (4) from the kit. Tighten the screws to 70-80 in-lbs (7.9-9.0 Nm). 6. Remove the two screws retaining the brake master cylinder reservoir cover. See Figure 3. Replace with the two standoff studs (1) in the kit. Tighten to 6-8 in-lbs (0.7-0.9 Nm)

HARLEY-DAVIDSON 5 Speed Transmissions 1984 – 1999 EVO / 5 Speed & 1999 – 2006 Twin Cam Installation Instructions

0

Filed Under (Harley Davidson) by admin on 26-11-2010

download
Remove Original Parts From Vehicle. 2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

KAWASAKI CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the key from the ignition switch. Loosen the vent hose on the cover. Remove the clutch cover bolts (10mm socket) and take the clutch cover off. You will need to unplug the wires from the electric actuator and small sensor in the center of the clutch cover to totally remove the cover. To unplug the wires from the sensors, follow the wires to the connections under the plastic side panel and unplug at that location. 2. Remove the primary clutch bolt (19mm socket). This is a left threaded bolt. Insert clutch puller by hand (right hand threads) and tighten until clutch pops off the shaft. This tool is available from EPI, part number PCP-10. Loosen the secondary clutch nut (27mm socket) and remove both clutches at the same time. When you slide the secondary clutch of the machine there are four metal roller pins inside the center shaft of the secondary clutch. These will normally stay in place but if one does fall out refer to assembly instructions in step #6. 3. Disassemble the primary clutch by removing the eight bolts on the cover plate (10mm socket) and remove the spring. Remove one nut (10mm) on the bolt that holds the weight in place, slide the pin out of the clutch and remove the weight. Install EPI weight making sure the tip of the weight is resting on the inside ledge of the clutch. Slide bolt through the holes in the clutch and the weight and install the nut. Repeat this step for the other three weights. NOTE: If your kit has two different gram weights, for example two 54 and two 56 weights, be sure to place them directly across from each other (or every other one). This keeps the clutch in balance . 4. Install the EPI spring and bolt the clutch cover back on using a criss-cross pattern to tighten down the cover. There is a mark on the cover plate and the spider usually in the form of a dot or arrow in the casting. These are alignment marks and must line up when the clutch is assembled. 5. EPI recommends cleaning your clutches when you have them off your machine. Use a clean rag or towel with contact or brake cleaner that does not leave any oily film. Clean all parts of the clutch except for the clutch bushings. Solvent can damage your bushings; just use a dry rag to clean them

Incoming search terms:

HARLEY DAVIDSON DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
These kits fit 1984 and later FXST, FXSTB, FXSTC, and 1993 and later FXDWG model motorcycles when equipped with passing lamps. INSTALLATION 1. To protect against scratches, cover gas tank and front fender before installation. is 01985 Figure 1. New Clutch Cable Routing 2. For FXSTB Models: Proceed to Step 3. For all except FXSTB: See Figure 1. Relocate the clutch cable to the inside of the handlebars as follows: a. Locate cable adjuster halfway along clutch cable by the front frame downtube and slide off rubber boot. b. Holding cable adjuster with 1/2 inch wrench, loosen jam nut using a 9/16 inch wrench. Back jam nut away from cable adjuster. Move adjuster toward jam nut to introduce a large amount of free play at hand lever. c. Remove small snap ring from pivot pin groove at bottom of clutch lever bracket. Remove pivot pin and clutch hand lever from bracket. Remove anchor pin and clutch cable eyelet from clutch hand lever. d. See Figure 1. Route clutch cable to the inside of the handlebars and reconnect clutch cable to clutch lever. e. See Figure 2. Turn cable adjuster away from jam nut until slack is eliminated at hand lever. Pull clutch cable ferrule away from clutch lever bracket to check free play. Turn cable adjuster to obtain 1/16-1/8 inch (1.6- 3.2 mm) free play between end of cable ferrule and clutch lever bracket. f. Hold adjuster with 1/2 inch wrench. Using 9/16 inch wrench, tighten jam nut against cable adjuster. Cover cable adjuster mechanism with rubber boot

Incoming search terms: