co ltdinc batteries suppliers and distributors in china fax mail

You search Auto repair manual PDF co ltdinc batteries suppliers and distributors in china fax mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY-DAVIDSON 12 VOLT BATTERIES CARE AND MAINTENANCE

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
CARE AND MAINTENANCE Voltmeter Test See Table 2. The voltmeter test provides a general indicator of battery condition. Check the voltage of the battery to verify that it is in a 100% fully-charged condition. If the open circuit (disconnected) voltage reading is below 12.7 V, charge the battery and then check the voltage again after the battery has set for one to two hours. If the voltage reading is 12.7 V or above, perform a load test. Table 2. Voltmeter Test For Battery Charge Conditions STATE OF CHARGE VOLTAGE (OCV) 100% 12.7 V 75% 12.6 V 50% 12.3 V 25% 12.0 V 0% 11.8 V Disconnection and Removal Refer to a service manual for specific disconnection and removal steps. Pay attention to all warnings and cautions within the manual and remove battery from battery box/tray. Battery Charging Batteries contain sulfuric acid, which could cause severe burns to eyes and skin. Wear a protective face shield, rubberized gloves and protective clothing when working with batteries. KEEP BATTERIES AWAY FROM CHILDREN. (00063a) 1. Never charge a battery without first reviewing the instructions for the charger being used. 2. Perform a voltmeter test to determine the state of charge. See BATTERY TESTING, VOLTMETER TEST. If battery needs to be charged, proceed to Step 3. Remove battery from motorcycle before charging. Electrolyte leakage will damage motorcycle parts. (00213a) Explosive hydrogen gas, which escapes during charging, could cause death or serious injury. Charge battery in a well-ventilated area. Keep open flames, electrical sparks and smoking materials away from battery at all times. KEEP BATTERIES AWAY FROM CHILDREN. (00065a) 3. See applicable service manual and remove the battery from the motorcycle. Place the battery on a level surface. 4. Inspect battery for damage. Replace battery if visibly damaged or frozen. 5. Inspect battery charger, verify that the charger leads are not damaged, frayed or loose

Incoming search terms:

Ready to Run 1/ 5-Scale Brushless EP Motorcycle

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
STABILIZER BAR INSTALLATION 3x8mm BH Screws ASSEMBLE THE BIKE STAND  Slide off the batttery tray door and install four “AA” batteries. Make sure the polarity is correct.  Turn on the transmitter and check the battery light. If the red light glows steadily, the batteries have enough voltage. If the red light blinks, the batteries are low and should be replaced.  Raise the antenna at the top of the transmitter. RED BATTERY LIGHT  The receiver should be factory bound to the transmitter. However, if you ever need to bind, follow these steps: 1. Turn on the transmitter. 2. Turn on the receiver via the switch on the ESC. If the receiver is not bound, the LED light will not be on. 3. Push and hold the bind button on the receiver until the light glows red. 4. Release the bind button. 5. If the binding is successful, the LED will fl ash once and then remain ON. 2. Make sure the collar is mounted on the center of the bar and tight the set screw. 3. Bend the rod and insert the ends into the bike. 4. Secure the bar to the bike using set screws. 1. Slide the metal collar onto the stabilizer bar. 4x4mm Set Screw (use threadlock) 3x3mm Set Screw (use threadlock) 4x4mm Set Screw (use threadlock) 4x4mm Set Screw (use threadlock) 4x4mm Set Screw (use threadlock)

YAMAH FJR PERIODIC MAINTENANCE AND MINOR REPAIR MANUAL

0

Filed Under (Yamaha) by admin on 22-11-2010

download
Battery The battery is located under panel D. (See page 6-7 for panel removal and installation procedures.) This motorcycle is equipped with a sealed-type (MF) battery, which does not require any maintenance. There is no need to check the electrolyte or to add distilled water. To charge the battery Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the motorcycle is equipped with optional electrical accessories. EW000116 WARNING ● Electrolyte is poisonous and dangerous since it contains sulfuric acid, which causes severe burns. Avoid any contact with skin, eyes or clothing and always shield your eyes when working near batteries. In case of contact, administer the following FIRST AID. •EXTERNAL: Flush with plenty of water. •INTERNAL: Drink large quantities of water or milk and immediately call a physician. •EYES: Flush with water for 15minutes and seek prompt medical attention. ● Batteries produce explosive hydrogen gas. Therefore, keep sparks, flames, cigarettes, etc., away from the battery and provide sufficient ventilation when charging it in an enclosed space. ● KEEP THIS AND ALL BATTERIES OUT OF THE REACH OF CHILDREN. To store the battery 1. If the motorcycle will not be used for more than one month, remove the battery, fully charge it, and then place it in a cool, dry place. 2. If the battery will be stored for more than two months, check it at least once a month and fully charge it if necessary. 3. Fully charge the battery before in- stallation Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage.

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

2009 Harley-Davidson FLH Series Independent Suspension Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Important Safety Precautions a. Make sure you have a clear understanding of all basic shop safety practices and that you wear appropriate clothing and use safety equipment. Be especially careful of the following: · Read all directions before you begin, and make sure you have the tools, the parts and the skills required to perform the tasks safely and completely.Harley-Davidson® FLH 2009 & Up Independent Suspension CHAMPION TRIKES Installation Guide Page 5 of 18 Revision 8 · Protect your eyes by using proper safety glasses, goggles or face shields anytime you hammer, drill, grind, pry or work around pressurized air or liquids, and springs or other stored-energy components. · Use other protective wear when necessary, for example gloves or safety shoes. Handling hot or sharp parts can cause severe burns or cuts. · Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. Make sure the engine is turned off and battery disconnected before you begin work. · Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine. · Burns from hot parts: Let the engine and exhaust system cool before working on those areas. · Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. c. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. d. Use only nonflammable solvent, not gasoline, to clean parts. e. Never drain or store gasoline in an open container. f. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.6 Specifications Overall Length: 103″ Overall Width: 57.25″ Wheel Base: 53″ Max Load Capacity: 600 Lb Max Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4 on 4.5 Tire Pressure: 24-26 PSI Suspension: Double A-arm Independent Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 5.75 cubic feet. Two full-face helmets and additional storage. *Champion does not change certain components that will affect EPA, CARB, or any laws that will change the emission characteristics of the motorcycle.

Incoming search terms:

Harley-Davidson FLH Series 2008 and Down, Independent Suspension Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 07-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. Make sure the engine is turned off and battery disconnected before you begin work.  Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine.  Burns from hot parts: Let the engine and exhaust system cool before working on those areas.  Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. c. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. d. Use only nonflammable solvent, not gasoline, to clean parts e. Never drain or store gasoline in an open container. f. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.5 Specifications Overall Length: 103″ Overall Width: 57.25″ Wheel Base: 53″ Load Capacity: 600 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4 on 4.5 Tire Pressure: 24-26 PSI Suspension: Double A-arm Independent Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 5.75 cubic feet. Two full-face helmets and additional storage.
Harley-Davidson® FLH 2008 & Down Independent Suspension CHAMPION TRIKES Installation Guide Page 6 of 20 Revision 4 2 Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted.  Seat – to be re-installed; without modification.  Left and right side covers – to be re-installed after modification.  Tour Box – to be re-installed (if so equipped).  Left and right saddle bags (if so equipped).  Left and right rear crash bars, saddlebag rails (if so equipped).  Tour Box mounting frame (if so equipped).  Left and right passenger foot rests – to be re-installed without modification.  Left and right mufflers  Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake Caliper is removed.  Remove Rear Caliper (disconnect brake line at Caliper). NOTE: Cap line to prevent introduction of dust / debris into line. Remove Caliper

Harley Davidson Softail 1987 to Current Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 05-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. c. d. e. f. Make sure the engine is turned off before you begin work. • Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine. • Burns from hot parts: Let the engine and exhaust system cool before working on those areas. • Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. Use only nonflammable solvent, not gasoline, to clean parts Never drain or store gasoline in an open container. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.4 Specifications Overall Length: 66″ Body Length: 92″ Wheel Base: 53″ Load Capacity: 620 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4×4.5 – (Current Installations – Alum Rear End) Wheel Size (15″) (5 lug) Offset +35 mm 15x7JJ 5×4.5 – (Later Installations – Black Rear End) Tire Size (16″) 215 / 60 / R16 Wheel Size (16″) (5 lug) Offset +40 mm 16x7JJ 5×4.5 – (First Installations – Black Rear End) Tire Pressure: 20 PSI Suspension: Internal Swing Arm utilizing OEM shocks Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 3.75 cubic feet. 2 full-face helmets and additional storage

Dual Battery Installation for 1985 Toyota 4Runner

0

Filed Under (Toyota Manuals) by admin on 16-09-2011

Download
I reviewed a number of locations on my 4Runner including the engine bay, under the body
and rear cargo area. Of all those areas, I decided on the engine bay as the most convenient,
the safest location and the easiest to wire and protect the batteries. Careful measurement of
the OEM battery location showed that by rotating the OEM battery 90 degrees, another
battery could be shoehorned in with some minor modifications. See figure 1 for a photo of
the OEM battery location.
The first problem to solve when mounting batteries in this location is to move the OEM fuse
box approximately 1” towards the rear of the truck. See figure 2 on how I was able to move
my fuse box 1” inch. There is just enough slack in the factory wiring harness to make this
move without having to redo wiring harnesses or putting undo pressure or tension on the
harness

TOYOTA ALL MODELS BATTERY MAINTENANCE FOR IN-STOCK VEHICLES

0

Filed Under (Toyota Manuals) by admin on 16-10-2011

download
A battery in a stored vehicle is subject to conditions which can reduce its performance and life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are recommended in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for excessively discharged and/or failed batteries due to
lack of maintenance. It is considered the dealers responsibility to maintain the specified state of charge of the vehicle’s battery while in stock. BATTERY MAINTENANCE RECOMMENDATIONS: 1. A monthly battery inspection is recommended under normal conditions. If your dealership is located in an area subject to extreme temperatures (hot or cold), periodic maintenance may need to be performed on a more frequent basis. When maintenance requires removal of filler plugs on vehicles with “maintenance free” batteries, new labels are available via the following part numbers:

Yamaha V-Star 650 Jet Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Remove the vacuum slide from the carburetor. • Remove the OEM needle and spacer, noting the order of assembly. • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needle. • Reinstall the OEM spacer and washer. • Reinstall the vacuum slide along with the diaphragm spring. • Reattach the diaphragm cover and tighten its screws. Note: Verify that the slide maintains a full range of movement! • Drain the fuel from float bowl and remove the bowl cover. • Remove the new cap head Allen screws in place of the OEM Phillips head screws. • Repeat above steps for other OEM main jet and pilot jet, and replace them with Baron’s main and pilot jets. • Thoroughly clean the inside of the float bowl prior to reinstalling it. • Reassemble the carburetor by reversing the order of previous steps. Use thecarburetor. • Locate the fuel mixture plug on each carburetor; it will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plug for each carburetor. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. b. Insert a self-tapping sheet metal screw into the drilled hole and remove the plug. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (2) Mikuni main jets, (2) pilot jets, (2) titanium needles, (2) clips, (8) cap head Allen screws Revision 2.0 c. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 turns. Refer to final step for assistance in fine-tuning the setting of the air/fuel adjustment screw. • Reinstall the OEM air filter assembly. • Check all vent lines, fuel lines, and linkage for any obstructions or blockage

Incoming search terms: