com cn hinge co ltd mail

You search Auto repair manual PDF com cn hinge co ltd mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY DAVIDSON SADDLEBAG HINGE STOP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. See Figure 2 and Table 1. Remove the saddlebag by opening the lid and turning the two bail head studs (1) 1/4 turn. Save the washers (A) and discard one of the studs (1). The rear stud and isolator will be replaced with new ones from the kit. NOTE Do Not remove the hinge assembly from the saddlebag lid. 2. See Figure 1. Drill the rivets out of the backing plate (C) from the lower rear saddlebag hinge. •Enlarge the backing plate holes by drilling with a #19 drill bit. 3. Remove the rear isolator and install the new rear isolator (2) from the kit to the saddlebag. NOTE It is recommended to use Loctite® 262, threadlocker and sealant on the threads of the hinge screws. 4. See Figure 2 and Table 1. Position the backing plate (C) inside the saddlebag and align with the rear hinge (B) and hinge stop (3) on the outside of the saddlebag. Assemble using the two TORX® head screws (5). 2 1 is05974 1. Rear hinge rivets (2) 2. Rear isolator Figure 1. Drill Out Rivets From Rear Hinge and Backing Plate 5. Install the saddlebag to the motorcycle using the longer bail head stud (1) from the kit and a washer for the rear of the saddlebag and the washer and front bail head stud previously removed for the front of the saddlebag. 6. Repeat steps 1-5 for the opposite saddlebag

1988-2000 Honda Goldwing GL 1500 Signal Mirror Installation Instructions

0

Filed Under (Honda) by admin on 29-01-2011

download
Start on either the left or right side mirror. These instructions start with the right side mirror. Pull back the rubber boot covering the mirror mount. 1 2 3 Remove the accessory compartment cover. Remove the four screws on all sides of the accessory compartment. Remove the accessory compartment from the motorcycle fairing and set it aside. 4 The motorcycle’s electrical wiring for turn indicators is located forward of the accessory compartment cavity and behind the front amber turn indicator light. Disconnect the wire connected to the turn indicator light. 5 There are three screws holding the mirror housing to the mirror mount. Remove the three screws. Set the mirror housing aside.
Mirror Replacement – 2 – Remove the three screws holding the hinge to the mirror housing. Remove the hinge and remove the rubber boot surrounding the mirror housing. 1 Match the base of the hinge up to the new Signal® mirror housing. Mark the place on the hinge where the Signal® mirror wire will go through. Drill a ¼” hole in the hinge. 2 Position the rubber boot over the Signal® mirror housing. 3 Guide the Signal® mirror wire harness through the drilled hole in the hinge. Mount the hinge on the Signal® mirror housing using the original three screws.

Incoming search terms:

HARLEY DAVIDSON VRSCD SADDLEBAG MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
INSTALLATION Prepare Bike for Hardware Installation 1. Use a suitable lift to support the motorcycle under the frame until the rear suspension is fully extended. NOTE To remove the tether from the hole in the frame, reach under the frame tube to align the metal tee (located on the end of the seat tether) with the tether cable. 2. See Figure 1. Unlatch and open seat. Remove tether (4) by sliding small clip (3) sideways through hole in frame. NOTE To remove the tubular plastic seat-hinge sleeve from the hinge, turn the sleeve to reveal the slotted length. Push on the slot with your finger to pop the sleeve off the hinge pins. Closing the seat slightly allows the sleeve to fall from the hinge-side of the seat, so be prepared to catch the sleeve. 3. Remove plastic sleeve (2) from hinge pins (1) and slide pins toward rear of bike. Remove seat. 2 1 4 3 is 00449 1. Hinge 2. Sleeve 3. Clip 4. Remove tether from frame Figure 1. Remove Seat 3 1 2 is 00450 1. Grabstrap 2. Passenger Pillion 3. Screw and Washer Figure 2. Remove Passenger Pillion 4. See Figure 2. Remove screw and washer (3) securing passenger pillion to frame. Slide pillion under grabstrap (1) and forward to disengage from tongue to remove. Save pillion mounting screw and washer for later use

HARLEY DAVIDSON POWER LOCK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove seat following the instructions in the appropriate Service Manual. Preparing the Saddlebags for Power Locks 1. Remove saddlebags following the instructions in the appropriate Service Manual. 2. See Figure 1. Remove lid (1) and hinge (2) from sad- dlebag. 3. Remove lock (3) from saddlebag. 4. See Figure 2. Set drill template on hinge surface of the saddlebag aligning the template (5) with hinge mounting holes (7). 5. See Figure 3. Drill 0.344 (11/32) inch diameter hole (1). 6. Place the template on the back of the saddlebag (4) aligning front mounting grommet (2) and forward latch bracket (1). 7. See Figure 4. Drill 0.500-0.515 inch diameter hole (1). 8. Repeat on the other saddlebag. 1 2 3 is04988 1. Saddlebag lid 2. Saddlebag hinge 3. Saddlebag lock Figure 1. Remove Lid, Hinge and Lock from Saddlebag

HARLEY DAVIDSON LOCKING GLOVE BOX DOOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. Unsnap the original equipment (O.E.) left-side glove box door, and unfasten the tether by bringing the aglet end (see Figure 1, B) out through the retaining hole. Always wear proper eye protection when drilling or grinding. Flying debris could cause serious eye injury. (00402e) 2. Using an 3/16 inch (5 mm) bit positioned in the center of each snap, drill out the four plastic snaps surrounding the glove box opening. NOTE The glove box door, hinge and frame assemblies are side- specific. The assemblies install so that the tether retaining hole (C) in the door frame is to the inboard side. 3. Obtain the new left-side glove box door, hinge and frame assembly (1), a lock (2) and a tether assembly (8) from the kit. Remove the nut (3) from the lock. 4. Insert the lock through the hole in the glove box door as shown. Assemble the tether over the lock threads with the tab (A) on the inboard side of the lock, same as the retaining hole in the door frame. Tighten securely. 5. Open the left-side door, and position the door assembly at the glove box opening, lining up the holes. 6. Insert a screw (9) through each of the holes in the door frame and glove box. Install a hex nut with washer (10) onto the threads of each screw. Tighten finger-tight. NOTE Ambient temperature should be at least 60° F (16° C) for proper adhesion of the gaskets to the glove box door frame. 7. Clean the glove box door frame with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. NOTE The glove box gaskets are side-specific. With the paper backing facing the door frame, the oblong hole at the top of the gasket is to the outboard side. 8. Obtain the left-side gasket (6) and a hinge gasket (7) from the kit. Install the gaskets to the glove box door frame. a. The gasket liner on the large gasket is split to aid alignment. Peel one half of the liner from the adhesive backing of the left-side gasket. b. Using the frame edges and screw heads as a guide, carefully position the gasket to the glove box door frame and press firmly into place. c. Peel the remaining half of the liner from the gasket backing, and carefully position the rest of the gasket to the door frame. Press firmly into place. d. Apply steady pressure for a few seconds at all areas of the gasket to verify proper adhesion. e. Peel the liner from the hinge gasket. f. Carefully position the gasket to the door frame above the hinge, and press firmly into place.

Incoming search terms:

HARLEY DAVIDSON PUSHBUTTON FUEL CONSOLE DOOR RELEASE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION 1. Open the fuel door. Remove and discard stock lock and nut. 2. See Figure 1. Install pushbutton lock (2) and nut (1) on fuel door. 3. Remove screws (A) and replace the stock hinge mounting clip with the hinge mounting clip (3) from the kit. Install stock screws. Do not over-tighten. 4. Close the fuel door. A small amount pressure will be needed to close the fuel door because it is now spring- loaded. NOTE To keep the pushbutton lock assembly operating smoothly, lightly spray lubricant on the mechanism as needed. SERVICE PARTS 1 2 3 B C A is05361 Figure 1. Service Parts: Console Pushbutton Fuel Door Release Table 1. Service Parts Part Number Description (Quantity) Item 84850-92 Nut, hex 1 Not Sold Separately Fuel release, pushbutton 2 10334 Clip, hinge mounting 3 Items mentioned in text, but not included in kit. Screw (2) A Hinge pin B Fuel door

Harley Davidson BoonDocker Nitrous System Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 2 of 10 This manifold is also designed to vary the float bowl pressure in relation to nitrous pressure, thus keeping the nitrous and fuel delivery in sync. Fluctuations in bottle temperature greatly affect nitrous pressure, which affects nitrous delivery. By automatically adjusting the fuel delivery as nitrous pressure varies, this manifold makes nitrous safe, reliable, and easy to use. Be sure to understand and follow the tuning instructions at the end of these instructions. Proper tuning is an important part of any performance-enhancing product. Part I – Bottle Installation A. Bottle Valve Fittings Insert the 4AN x 1/8″ NPT fitting and the 1/8″ NPT Plug into the bottle valve (these are attached to the lid of the box for the bottle) . Use Teflon tape to seal the threads – be sure not to get tape inside the threads! B. Bottle Mounting Position With nitrous in the bottle, both nitrous liquid and nitrous gas are present under high pressure (760 psi at 70 deg F) . Due to gravity and acceleration forces, the liquid portion of the nitrous will be at the bottom and rearward parts of the bottle. For this nitrous system to work properly, it is important that nitrous liquid be drawn from the bottle. Nitrous vapor will cause a significant decrease in performance. For best results, the bottle should be mounted so the valve is pointed down and towards the back of the vehicle as shown below. ************** *************** ******** ********* *************** (can be installed on top or bottom of air boot) ********** ********* push-button switch (mounts on handlebar) +12 V *********** ************ **** ****** *! “**#$******%* *! “**#$*#*%* 20 deg to 90 Front of motorcycle Rear of motorcycle BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 3 of 10 Bottle mounted inside airbox: For some applications, a small bottle can be mounted inside the airbox as shown. Note: because of the restricted space, it was necessary to mount this bottle at a non-optimal angle (the valve is pointed towards the front instead of the rear)

Incoming search terms:

HARLEY DAVIDSON SPORT WIND DEFLECTOR AND WINDSHIELD KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
HEADLAMP VISOR INSTALLATION (2004 ONLY) 1 2 is 01467 1. Headlamp 2. Headlamp bracket mounting screws Figure 1. Remove Headlamp Mounting Screws (Left Side Shown) 1. See Figure 1. While holding the headlamp (1), remove the left and right headlamp bracket mounting screws (2). 2. See Figure 5. Obtain the headlamp visor (2) from the kit. 3. See Figure 2. Orient the headlamp visor (1) between the headlamp and headlamp mounting bracket (2) and reinstall the headlamp bracket mounting screws (3) securing the visor and headlamp to the headlamp mounting bracket. 4. Refer to the Service Manual and adjust the headlamp for the correct angle. 2 1 3 is01468 1. Headlamp visor 2. Headlamp mounting bracket 3. Headlamp mounting bracket screw Figure 2. Install Visor Between Headlamp and Mounting Bracket (Left Side Shown) 1 2 3 is03212 1. “RT” or “LFT” marking 2. Hinge-pin head faces up 3. Clamp post socket faces outward Figure 3. Fork Tube Clamp and Post Identification (Right-Side Clamp Shown) WINDSHIELD INSTALLATION 1. See Figure 5. Obtain one of the lower mount kits from the windshield kit carton. Identify the fork tube clamp for right- side (RT) or left-side (LFT) installation as indicated in Figure 3. NOTE The lower grommets (4) have been pre-installed into the Lexan® windshield. 2. Insert the rounded end of the post into the socket in the fork-tube clamp, oriented as shown in Figure 5. Lining up the hole in the end of the post with the hole in the clamp. With a 3 mm hex key, fasten the post to the clamp with the flat-head screw (16) from the kit, and tighten to 6.8 Nm (60 in-lbs ). 3. Place the clamp around the correct-side fork tube with the hinge-pin head facing up. Insert the two longer screws (15) from the lower mount kit through the counterbored holes in the outboard side of the clamp, and thread the screws part-way into the tapped holes in the inboard half. 4. Position the clamp so the top surface is approximately 6 to 13 mm (1/4 to 1/2 inch) below the upper triple-tree, and the hinge pin is straight forward. With a 4 mm hex key, tighten the screws just enough to hold the clamp in posi- tion. 5. Obtain the remaining lower mount kit and repeat Steps 2 through 4 to install the clamp to the opposite fork tube. 6. Obtain the upper mount kit from the windshield kit carton. NOTE The upper grommets (4), socket assemblies (3), windshield mount caps (6) and 5 mm screws (9) have been pre-installed into the windshield. 7. Place one of the handlebar clamps (5) onto one side of the handlebar, in the straight section between the riser and the handlebar controls, oriented as shown in Figure 4. NOTE Temporarily disengage the switch harness retainer from the handlebar to allow installation of the clamp.

HARLEY DAVIDSON VRSC ACCESSORY SEATS AND PILLIONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
INSTALLATION Installing Seat and Pillion Kits: 51584-01, 52028-02, 52036-01, 53432-02, or 52927-05 NOTE Proper installation of 53432-02 (Sundowner) and 52927-05 (Tallboy) requires installation of Fender Base Plate Kit 51120- 01 1. Refer to the appropriate Service Manual and remove the stock seat and pillion. 2. See Figure 2. Remove the two mounting bolts (2) from the passenger grabstrap (1). Save the bolts for re-installa- tion. NOTE The grabstrap must loop toward the rear. Check that the “Harley-Davidson” text on the grabstrap can be read from the front of the vehicle. 3. See Figure 2. Install stock grabstrap bolt, and one end of grabstrap as shown. While holding the grabstrap end parallel to the formed line of the fender, tighten the bolt to 8-12 Nm (71-106 in-lb ) . Repeat for opposite end of grabstrap. NOTES The new pillions included in Kits 52028-02 (Custom), 52036- 02 (Badlander) and 51584-01 (Leather Badlander) are installed from front-to-back. The pillion included in Kits 53432-02 (Sundowner) and 52927- 05 (Tallboy) must be installed through the grabstrap from back- to-front. To install the Sundowner or Tallboy Pillion on a motorcycle having a sissybar upright installed on Fender Base Plate Kit 51120-01, remove the upright before installing the pillion. Reinstall the upright after the Sundowner Pillion is installed. For kit numbers 52028-02 (Custom), 52036-01 (Vinyl Bad- lander) and 51584-01 (Leather Badlander) Seat Kits, be aware of the following: The 2003 Model Year 100th Anniversary VRSCA vehicle with two-tone sterling silver and vivid black paint has protective tape covering the rear under-the-seat area of the airbox cover. For the seats listed above, it will be necessary for cosmetic reasons, to carefully remove the protective tape and reapply it so it is in the correct position for these shorter-nose seats. Some trimming of the lower portion of the protective tape may be necessary to eliminate interference with the airbox cover latch. If necessary, reorder protective tape (48403-03). 4. Install new pillion into position through grabstrap. Prevent pinching TSSM control wiring by routing the cable through the channel on the underside of the pillion (see Figure 2) and away from the pillion mounting bolt. Pinched wiring may damage the TSSM system. 1 3 2 is00014 1. Pillion 2. Grabstrap 3. Pillion base mounting hole Figure 3. Pillion Base Mounting Hole 5. See Figure 3. Push the pillion (1) forward through the grabstrap (2) until the pillion mounting hole is approximately 25 mm (1 in.) forward of the hole (3) in the frame. 6. See Figure 2. Push down on the pillion and slide the pillion toward the rear to engage the pillion slot with the fender tongue (5). Push rearward until the pillion mounting holes align. After installing pillion, pull upward to be sure it is locked in position. While riding, a loose pillion can shift causing loss of control, which could result in death or serious injury. (00387a) 7. Install original pillion mounting bolt. Tighten bolt to 11-14 Nm (97-124 in-lb ) . 8. Re-install the sissybar upright, if removed earlier. 9. Position the seat (as if opened) onto the frame. Slide the seat forward to insert the seat-hinge pins into the bushings on the frame. 10. See Figure 1. Clip the plastic seat-hinge sleeve (2) over the seat hinge. 11. See Figure 1. Insert the seat tether (3) into the hole in the motorcycle frame. 12. Refer to the applicable Owner’s Manual and close the seat. Installing Seat Kits: 51595-05, 52024-01, or 51647-06 Kit 51595-05 requires the use of pillion kit 51594-05. Kit 51647-06 requires the use of pillion kit 51648-06. Kit 52024-01 requires the use of either the stock pillion or Touring Pillion 52023-01A. 1. Refer to the appropriate Service Manual and remove the stock seat.

Incoming search terms:

Kawasaki Teryx 750 Cab Enclosure Kit Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove seats and set aside for better access to vehicle interior. Refer to Owner’s Manual for instructions. ii) Remove lower foot guardrails and set shoulder screws aside for later use. Loosen 19mm bolts ( A in Fig.1) until 3/16″ gap can be achieved. iii) Loosely fasten rubber stops ( B in Fig.1) to Hinge Mounting Brackets using 6mm bolts. Mount brackets to vehicle as shown in Fig.1 and hand tighten 19mm bolts. iv) Align lower bracket hole to existing foot guard mounting hole and fasten with OEM shoulder screw ( C in Fig.1). NOTE : Apply pressure to screwdriver in order catch threads on nuts. v) Adjust upper edge of brackets with mallet to make bracket edge flush to roll bar edge (Fig.2). Tighten 19mm bolts. Adjust and tighten rubber mounts. FLUSH A B Fig.2 Fig.1 2. Rear Bracketery i) Remove 14mm bolts from lower mounting points on rear crossbar. Install Striker Mounting Brackets as shown (Fig.3). Reinstall bolts and hand tighten only . Attach Striker Plates using (4) ¼-20 x 3/8″ screws, keep loose for later adjustment. ii) Remove 14mm bolts from upper crossbar and install Upper Rear Panel Brackets as shown (Fig.4). Tighten 14mm bolts back into place. 3. Panel Installation i) Install low density foam to interior of panels as shown (Fig.5.) Approx. (8) 3″ long strip are required on each side panel. Install low density foam to entire door / panel interface. ii) Mount side panels to roll cage and temporarily clamp to top roll bar. Loosely insert remaining (2) shoulder screws to each foot well. Adjust each panel to obtain proper alignment at front, top and lower rear. iii) Ensure hinge mounting bracket edges are flush with inside door frame and transfer hinge bolt hole locations onto plastic panels. Remove panels and drill holes using ¼” bit. Re-install panels and shoulder screws onto vehicle. iv) Mount hinges as shown (Fig.6) with (8) ¼-20 x 5/8″ Lg. Flat Head screws. DO NOT OVER TIGHTEN