commin issueswith 2011 teryx

You search Auto repair manual PDF commin issueswith 2011 teryx, if there are search results will appear below. If search results do not exist, please search by others keyword.





2011 HONDA CBF1000/ CBF1000 ABS Specifications

0

Filed Under (Honda) by admin on 18-02-2011

download
Press information for 2011 CBF1000 / CBF1000 ABS 7 Specifications – CBF1000 (ED-type) ENGINE Type Liquid-cooled 4-stroke DOHC inline-4 Displacement 998cm3 Bore  Stroke 75  56.5mm Compression Ratio 11.2 : 1 Max. Power Output 79kW/9,000r/min -1 (95/1/EC) Max. Torque 96Nm/6,500r/min -1 (95/1/EC) Idling Speed 1,200min -1 Oil Capacity 3.6 litres FUEL SYSTEM Carburation PGM-FI Throttle Bore 36mm Aircleaner Dry, cartridge-type paper filter Fuel Tank Capacity 20 litres Fuel Consumption 18,4 km/l (WMTC Mode #) ELECTRICAL SYSTEM Ignition System Computer-controlled digital transistorised with electronic advance
Press information for 2011 CBF1000 / CBF1000 ABS 8 Ignition Timing 5° BTDC (idle) ~ 45° BTDC (7,500min -1 ) Sparkplug Type IMR8C-9HES Starter Electric Battery Capacity 12V/8.6AH ACG Output 350W/5,000 rpm Headlights 12V, 55W  1 (low) / 55W  1 (high) DRIVETRAIN Clutch Wet, multiplate with coil springs Clutch Operation Hydraulic Transmission Type 6-speed Primary Reduction 1.6 Gear Ratios 1 2.6 2 1.83 3 1.5 4 1.32 5 1.17 6 1.07 Final Reduction 2.687 (43/16) Final Drive #530 O-ring sealed chain FRAME Type Mono-backbone; cast aluminium
Press information for 2011 CBF1000 / CBF1000 ABS 9 CHASSIS Dimensions (LWH) 2,210  780  1,220mm Wheelbase 1,495mm Caster Angle 26° Trail 110mm Turning Radius 2.9m Seat Height 795mm ±15mm Ground Clearance 135mm Kerb Weight *245kg (F: 120kg; R: 125kg) Max. Carrying Capacity 195kg Loaded Weight *440kg SUSPENSION Type Front 41mm free valve-type telescopic fork & adjustable spring; 120mm stroke Rear Gas-charged HMAS damper & adjustable spring and rebound; 120mm axle stroke WHEELS Type Front Hollow-section 6-spoke cast aluminium Rear Hollow-section 6-spoke cast aluminium Rim Size Front 17M/C  MT3.5 Rear 17M/C  MT5
Press information for 2011 CBF1000 / CBF1000 ABS 10 Tyre Size Front 120/70 ZR17M/C (58W) Rear 160/60 ZR17M/C (69W) Tyre Pressure Front 250kPa Rear 290kPa (290kPa with passenger) BRAKES Type Front 296  4.5mm dual hydraulic disc with 2- piston calipers, floating rotors, sintered metal pads (*3-piston calipers and Combined ABS) Rear 240  5.0mm hydraulic disc with 1-piston caliper, sintered metal pads (*and Combined ABS) *C-ABS version All specifications are provisional and subject to change without notice

2011 HONDA NT700V Specifications/ Press Information

0

Filed Under (Honda) by admin on 18-02-2011

download
Press information for 2011 NT700V 5 Specifications – NT700V (ED-type) ENGINE Type Liquid-cooled 4-stroke 8-valve SOHC 52° V- twin Displacement 680cm 3 Bore  Stroke 81  66mm Compression Ratio 10 : 1 Max. Power Output 48.3kW/8,000min -1 (95/1/EC) Max. Torque 66.2Nm/6,500min -1 (95/1/EC) Idling Speed 1,200min -1 Oil Capacity 3.2 litres FUEL SYSTEM Carburation PGM-FI electronic fuel injection Throttle Bore 40mm Aircleaner Dry, cartridge-type paper filter Fuel Tank Capacity 19.7 litres (including 3.5-litre reserve) Fuel consumption 20.1 km/l (WMTC Mode #) ELECTRICAL SYSTEM Ignition System Digital transistorised with electronic advance Ignition Timing 10° BTDC (idle) ~ 45° BTDC (8,900min -1 ) Sparkplug Type CPR8EA-9 (NGK) Starter Electric Press information for 2011 NT700V 6 Battery Capacity 12V/11.2AH ACG Output 438W Headlight 12V; 55W  1 (low) / 55W  1 (high) DRIVETRAIN Clutch Wet, multiplate with coil springs Clutch Operation Mechanical; cable-actuated Transmission Type 5-speed Primary Reduction 1.763 (67/38) Gear Ratios 1 2.571 (36/14) 2 1.688 (27/16) 3 1.300 (26/20) 4 1.084 (29/27) 5 0.923 (24/26) Final Reduction 3.091 (34/11) Final Drive Enclosed shaft FRAME Type Diamond; steel twin-spar CHASSIS Dimensions (LWH) 2,218  810  1,320mm (Raised windscreen: 1,491mm) Wheelbase 1,476mm Caster Angle 28° 50′ Trail 115mm
Press information for 2011 NT700V 7 Turning Radius 3.2m Seat Height 805mm Ground Clearance 156mm Kerb Weight 254kg (F: 112kg; R: 142kg) *257kg (F: 113kg; R: 144kg) Max. Carrying Capacity 197kg Loaded Weight 451kg *454kg SUSPENSION Type Front 41mm telescopic fork, 115mm axle travel Rear Single damper with adjustable preload, 122.5mm axle travel WHEELS Type Front S-section triple-spoke cast aluminium Rear S-section triple-spoke cast aluminium Rim Size Front 17  MT3.5 Rear 17  MT4.5 Tyre Size Front 120/70 ZR17 (58W) Rear 150/70 ZR17 (69W) Tyre Pressure Front 250kPa Rear 290kPa (290kPa with passenger) BRAKES Type Front 296  4.5mm dual hydraulic disc with Combined 3-piston calipers and sintered metal pads Press information for 2011 NT700V 8 Rear 276  6mm hydraulic disc with dual-piston caliper and sintered metal pads (*and Combined ABS) *Combined-ABS version

Incoming search terms:

2011 HONDA XL1000V Specifications / Press Information

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications – XL1000V / XL1000V ABS (ED-type) ENGINE Type Liquid-cooled 4-stroke 8-valve DOHC 90° V- twin Displacement 996cm 3 Bore  Stroke 98  66mm Compression Ratio 9.8 : 1 Max. Power Output 69kW/7,500min -1 (95/1/EC) Max. Torque 98Nm/6,000min -1 (95/1/EC) Idling Speed 1,300min -1 Oil Capacity 4.1 litres FUEL SYSTEM Carburation PGM-FI electronic fuel injection Throttle Bore 42mm Aircleaner Viscous, cartridge-type paper filter Fuel Tank Capacity 25 litres (including 4-litre warning light reserve) ELECTRICAL SYSTEM Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 15° BTDC (idle) ~ 55° BTDC (5,100min -1 ) Sparkplug Type IJR8B9 (NGK) Press information for 2011 XL1000V 6 Starter Electric Battery Capacity 12V/18AH ACG Output 434W Headlight 12V 60W  2 (low) / 55W  2 (high) DRIVETRAIN Clutch Wet, multiplate with coil springs Clutch Operation Mechanical; cable-actuated Transmission Type 6-speed Primary Reduction 1.682 (44/74) Gear Ratios 1 2.571 (14/36) 2 1.684 (19/32) 3 1.292 (24/31) 4 1.100 (30/33) 5 0.969 (32/31) 6 0.853 (34/29) Final Reduction 2.938 (16/47) Final Drive O-ring sealed chain FRAME Type Steel tube CHASSIS DIMENSIONS Dimensions (LWH) 2,300  930  1,465mm Wheelbase 1,560mm Caster Angle 27° 30′ Press information for 2011 XL1000V 7 Trail 110mm Turning Radius 2.58m Seat Height 838mm Ground Clearance 181mm Kerb Weight 268.7kg (F: 126.3kg; R: 142.4kg) *276.7kg (F: 130kg; R: 146.7kg) Max. Carrying Capacity 201kg Loaded Weight 469.7 kg *477.7 kg SUSPENSION Front 43mm telescopic fork, 155mm axle travel Rear Pro-Link damper, 145mm axle travel WHEELS Type Front Hollow-section triple-spoke cast aluminium Rear Hollow-section triple-spoke cast aluminium Rim Size Front 19M/C  MT2.50 Rear 17M/C  MT4.00 Tyre Size Front 110/80 R19M/C (59H) Rear 150/70 R17M/C (69H) Tyre Pressure Front 250kPa Rear 250kPa (with passenger: 280kPa) Press information for 2011 XL1000V 8 BRAKES Front 296  4.5mm dual hydraulic disc with Combined 3-piston calipers (*ABS) and sintered metal pads Rear 256  5mm hydraulic disc with Combined 3- piston caliper (*ABS) and sintered metal pads * Combined-ABS version All specifications are provisional and subject to change without notice

Kawasaki Teryx Skid Plate Installation And Removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Let skid sit in sun or inside house at room temperature for a couple hours. Cold weather can shrink plastic slightly but this is not an issue once installed. 2. Remove Stock Teryx Hardware/skids and set aside hardware to use on new skid 3. You have a couple options in mounting the new skids. 1) remove stock metal engine inspection cover underneath Teryx, or 2) using UHMW skid as template cut out hole in inspection cover (A below) to allow access to oil filter. Cut hole substantially larger than skid hole so as not to cut yourself when removing/installing oil filter 5. Fasten all main skid bolts and washers, but do not tighten all the way so that you are able to move skid slightly to center all bolt holes. 6. Fasten all front and rear skid bolts and washers, but do not tighten all the way so that you are able to move skid slightly to center all bolt holes. . Once skids are in desired location tighten all bolts 9. You will be required to drill 2 – 3/16 pilot holes in the 2 rear most main skid mounting locations. Use the supplied self tapping bolts and washers to attach skid in these locations

2008-2009 KAWASAKI TERYX HEADLAMPS HIDTERYX HID KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
a. Remove rubber boot from the back of the headlamp housing assembly. b. Push down on metal latch and pull away from lip to release halogen bulb. Pull out halogen bulb. c. Insert HID bulb, line up bulb to fit into the bulb holder, lower latch to lock bulb in place. d. Replace Rubber boot on the back headlamp assembly. (Make sure to pull wires through the center of the rubber boot first before you start to pull down boot on the back of the headlamp assembly.) e. Make sure that the wiring, coming from the HID bulb, clears the black plastic housing that encases the headlamp assembly so connection from the bulb to the ballast is possible. If installed correctly there is no need for drilling or modifications of any type. 2. Ballast a. Mount ballast in location of your choice – recommended near the headlight. 3. Wiring Note: DO NOT modify the wiring that runs from the HID bulb to the ballast. It will cause the system to work improperly. It will void the warranty . a. Once ballast is installed connect corresponding wires from HID bulb to corresponding male / female plugs on ballast. b. To connect wiring from ballast to Teryx primary system i. Find wire extension with white triangular head with black, yellow & green wires at opposite end ii. Connect black off extension to black wire coming off ballast iii. Connect Yellow / Green wire to red wire coming off ballast iv. Connect triangular head to corresponding plug on Teryx Factory Wiring End

2011 HONDA CRF250X Specifications

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications CRF250X (ED-type) ENGINE Type Liquid-cooled 4-stroke 4-valve SOHC single Displacement 249cm 3 Bore  Stroke 78  52.2mm Compression Ratio 12.9 : 1 Max. Power Output 21.9kW/9,000min -1 (95/1/EC) Max. Torque 24.2kW/8,000min -1 (95/1/EC) FUEL SYSTEM Carburation 37mm Keihin FCR flat slide carburettor with throttle position sensor (TPS) Fuel Tank Capacity 7.3 litres (including 1.6-litre reserve) ELECTRICAL SYSTEM Ignition System Computer-controlled digital capacitor discharge with electronic advance and lighting coil Starter Electric / Primary kick DRIVETRAIN Transmission 5-speed Primary Reduction 3.611 (65/18) Gear Ratios 1 2.384 (31/13) 2 1.750 (28/16) 3 1.333 (28/21) 4 1.041 (25/24) 5 0.814 (22/27) Final Reduction 3.786 (53/14) Final Drive #520 T-ring roller chain FRAME Type Semi-double cradle; aluminium twin-spar CHASSIS Dimensions (LxWxH) 2,174 x 827 x 1,261mm Wheelbase 1,481mm Caster Angle 27˚ 54′ Trail 118mm Seat Height 958mm Press information for 2011 CRF250X 3 EU-EN Ground Clearance 346mm Kerb Weight 115kg SUSPENSION Type Front 47mm inverted Showa leading-axle twin- chamber cartridge-type telescopic fork with 16-step adjustable compression and rebound damping; 280mm axle travel Rear Pro-Link with single Showa damper, adjustable low-speed (13-step) & high-speed (3.5-turn) compression and 17-step rebound damping; 313mm axle travel WHEELS Type Front Aluminium rim/wire spoke Rear Aluminium rim/wire spoke Rim Size Front 21 x 1.60 Rear 18 x 2.15 Tyre Size Front 90/90-21 M/C 54R Rear 120/90-18 M/C 65R BRAKES Type Front 240  3mm hydraulic disc with dual-piston caliper and sintered metal pads Rear 240  4mm hydraulic disc with single-piston caliper and sintered metal pads

2011 FORD HARLEY-DAVIDSON F-150 TECHNICAL SPECIFICATIONS

0

Filed Under (Harley Davidson) by admin on 01-11-2010

download
Final assembly location Dearborn Truck Plant, Dearborn, Mich. POWERTRAIN AND CHASSIS ENGINE Type 6.2-liter two-valve V8 Configuration Iron block, aluminum heads Valvetrain SOHC, two valves per cylinder, roller-rocker shaft with hydraulic lash adjusters Bore x stroke 4.02 x 3.74 inches Displacement 379 cubic inches, 6,210 cc Compression ratio 9.8:1 Horsepower 411 hp @ 5,500 rpm Torque 434 lb.-ft. @ 4,500 rpm Fuel Injection Sequential multi-port electronic Oil capacity Seven quarts DRIVETRAIN Layout RWD or AWD TRANSMISSION Standard Six-speed automatic overdrive Gear ratios 1st 4.17:1 2nd 2.34:1 3rd 1.52:1 4th 1.14:1 5th 0.86:1 6th 0.69:1 Reverse 3.40:1 Available axle ratios 3.73 SUSPENSION Front 4×2 Coil-on-shock, long-spindle double-wishbone independent, stamped-steel lower control arm (sport-tuned) Front 4×4 Coil-on-shock, long-spindle double-wishbone independent, stamped-steel lower control arm (sport-tuned) Rear 4×2 Hotchkiss-type non-independent live, leaf springs and outboard shock absorbers (sport-tuned) Rear 4×4 Hotchkiss-type non-independent live, leaf springs and outboard shock absorbers (sport-tuned) STEERING Type Power rack-and-pinion Turning circle curb-to-curb 47.0 feet 2011 FORD HARLEY-DAVIDSON F-150 TECHNICAL SPECIFICATIONS BRAKES Front 13.8-inch vented disc Rear 13.7-inch vented disc Assist type Vacuum, RSC WHEELS AND TIRES Wheels 22-inch polished forged aluminum with painted accents with “Harley- Davidson” Bar & Shield logo on wheel ornament Tires P275/45R-22 all-season BSW DIMENSIONS (inches unless otherwise noted) EXTERIOR SuperCrew RWD SuperCrew AWD Wheelbase 144.5 144.5 Vehicle length 231.9 231.9 Vehicle width (without mirrors) 79.2 79.2 Vehicle height 74.8 75.9 Track width, front/rear 67.0/67.0 67.0/67.0 Cargo box length 67.0 67.0 Width (max) between wheels 50.0 50.0 Inside box height 22.4 22.4 INTERIOR Seating capacity Five Five Headroom Front row 41.0 41.0 Rear row 40.3 40.3 Legroom Front row 41.4 41.4 Second row 43.5 43.5 Shoulder room Front row 65.9 65.9 Second row 65.5 65.5 Hip room Front row 60.5 60.5 Second row 64.6 64.6 WEIGHTS AND TOWING (pounds)

KAWASAKI TERYX 750 CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove both seats from the vehicle. Next, remove the passenger side lower body panel. There is a mixture of Philips head screws and also plastic push pin fasteners that have to be removed. 2. With the side panel off, the next item to remove is the plastic housing over the engine. These are all “push in” style plastic clips that hold it in place. Once all the pins are out, you can slide the housing off and set it aside. 3. Now the lower long plastic panel under the seat has to be removed (again mainly plastic push clips to remove) . Once they are all out, carefully remove and set aside. 4. Next, remove the fuel tank. Remove the two lines on the top of the tank. There are two straps that hold the tank in place. Remove the bolt from each strap, remove the straps, and lift the fuel tank out. 5. Now the bracket that holds the fuel pump on has to be removed. There are two bolts here to take out. Once this is done, mark the two wires to the coil and disconnect them. Set the bracket out of the way . 6. Next, the clutch cover bolts can be removed and the norkel on the housing can be loosened and i Teryx 750 Clutch Kit Instructions 5/1/09 removed. Take the clutch cove off and set out of the way. 7. With the clutch visible, you can remove the secondary clutch with a large impact wrench and metric socket . 8. Remove the bolt from the primary clutch. This is a left hand thread on the bolt. Next you will need a Kawasaki drive clutch puller (part #352251) to pop the clutch loose. If you do not have a puller, the spring cap can be removed on the vehicle and the weights can be changed out in there as well. 9. With the clutches sitting on the bench, remove the bolts that hold on the spring cover. Remove the stock spring and the stock weights 10. After reading the directions on the new weights, add the correct amount of weight to each clutch weight and install them in the clutch. Place the weight to the left side in the clutch pocket and then install the aluminum spacer. Repeat this process for the other three weights. 11. Install the new spring supplied in the kit and install the spring cover, paying close attention to the arrows on the cover. 12. Next, remove the stock spring from the secondary. It is recommended that you use the TEAM Compression tool (part # 930001) for this. With the clutch on the compression tool, compress the spring retainer down far enough to remove the snap ring with the needle-nose pliers . Slowly back off the t-handle and remove the tool.

Kawasaki Teryx Electric Steering Installation Manual

0

Filed Under (Kawasaki) by admin on 29-04-2012

download
installation Instructions for Kawasaki Teryx 1. Before installation, center steering wheel and verify tires are straight. 2. Begin by removing all Phillips screws retaining the plastic hood to the front grill, headlights, and frame structure and remove front clip assembly. 3. Remove plastic shroud by removing the 4 phillips screws that retain it to the frame. 4. There are 2 bolts that hold the steering column tube in place and you need to reach up under frame work to get to them. They are 14 mm and you need a box and open end wrench to access them. Loosen the upper one and remove the lower one. Remove the pinch bolt at the column shaft and u-joint. Remove the lower pinch bolt at the rack and u-joint and while tilting the column up and down remove the stock steering shaft.
5. Once the shaft is removed, you are ready for installation. Your bracket and motor has come completely assembled as shown below. You will need to remove the lower shaft from the motor to install it. After removal of the shaft you will need to loosen the 3 mounting bolts from the bracket to the motor to allow clearance for the bracket to slide over the frame piece where it will mount

Kawasaki Teryx Bowkaddy Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The most effective method of mounting Bowkaddy on a Kawasaki Teryx is with the use of Kaddy Bracket UTV. However, one small after-market modification is necessary to make the bracket fit the rear roll bars on these side by side vehicles. Two additional 21/64″ holes must be drilled in the bracket at the locations shown in the image below. For more product and installation information,