contactus co ltd sockets 163 com mail

You search Auto repair manual PDF contactus co ltd sockets 163 com mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





Yamaha V-Star 1100 Needle/ Jet Kit REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 27-12-2011

download
To install this needle and jet kit: • Remove carburetors from the engine per Yamaha shop manual procedures. Note: Always perform internal carburetor work in a clean area. • Remove the vacuum slide from each carburetor. • Remove the OEM needle, spacer and washers, noting order of assembly. (Note; the washers are used as shims to raise the needle, each is equivalent to ½ clip position, use these to fine tune the needle) • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needles. The top is the blunt end of the needle. • Reinstall the OEM spacer and washers as shown in the figure below. • Reinstall the vacuum slides along with the diaphragm spring and reattach the diaphragm covers Note: Verify that the slides maintain their full range of movement! • Drain the fuel from the float bowls and remove the bowl covers. • Remove the OEM main jets and replace them with Baron’s supplied Mikuni main jets. Install the “base setting” main jets as indicated above. NOTE: V-Star 1100 carburetion runs staggered jetting! Make sure the front cylinder’s carburetor gets the larger main jet (numerically), and the rear cylinder’s carburetor gets the smaller main jet . Important! Extra jets have been included in your kit. These will help you fine-tune the carburetors for changing conditions. These conditions include climate and weather patterns in your area as well as exhaust equipment on your motorcycle. Barons determines the jet and clip recommendations that best suit your average riding conditions based upon information supplied to us at the time of your order. Changes in weather, altitude or modifications to your exhaust system may require jets other than those supplied. • Thoroughly clean the inside of the float bowls prior to reinstalling them. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (4)Mikuni main jets #107.5, 110, 112.5, 115, (2) titanium needles, (2) clips, (8) cap-head allen screws Tools required: 3-4-5 mm allen wrenches, 10&12 mm sockets, 10mm end wrench, phillips & flat screwdrivers, pliers, drill. Revision 4.0 • Reassemble the carburetors by reversing the order of above steps. Use the new supplied cap head Allen screws in place of the OEM Phillips head screws for the float bowls. • Locate the fuel mixture screws – they will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plugs

Harley Davidson BoonDocker Nitrous System Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 2 of 10 This manifold is also designed to vary the float bowl pressure in relation to nitrous pressure, thus keeping the nitrous and fuel delivery in sync. Fluctuations in bottle temperature greatly affect nitrous pressure, which affects nitrous delivery. By automatically adjusting the fuel delivery as nitrous pressure varies, this manifold makes nitrous safe, reliable, and easy to use. Be sure to understand and follow the tuning instructions at the end of these instructions. Proper tuning is an important part of any performance-enhancing product. Part I – Bottle Installation A. Bottle Valve Fittings Insert the 4AN x 1/8″ NPT fitting and the 1/8″ NPT Plug into the bottle valve (these are attached to the lid of the box for the bottle) . Use Teflon tape to seal the threads – be sure not to get tape inside the threads! B. Bottle Mounting Position With nitrous in the bottle, both nitrous liquid and nitrous gas are present under high pressure (760 psi at 70 deg F) . Due to gravity and acceleration forces, the liquid portion of the nitrous will be at the bottom and rearward parts of the bottle. For this nitrous system to work properly, it is important that nitrous liquid be drawn from the bottle. Nitrous vapor will cause a significant decrease in performance. For best results, the bottle should be mounted so the valve is pointed down and towards the back of the vehicle as shown below. ************** *************** ******** ********* *************** (can be installed on top or bottom of air boot) ********** ********* push-button switch (mounts on handlebar) +12 V *********** ************ **** ****** *! “**#$******%* *! “**#$*#*%* 20 deg to 90 Front of motorcycle Rear of motorcycle BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 3 of 10 Bottle mounted inside airbox: For some applications, a small bottle can be mounted inside the airbox as shown. Note: because of the restricted space, it was necessary to mount this bottle at a non-optimal angle (the valve is pointed towards the front instead of the rear)

Incoming search terms:

Yamaha V-Star 650 Jet Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Remove the vacuum slide from the carburetor. • Remove the OEM needle and spacer, noting the order of assembly. • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needle. • Reinstall the OEM spacer and washer. • Reinstall the vacuum slide along with the diaphragm spring. • Reattach the diaphragm cover and tighten its screws. Note: Verify that the slide maintains a full range of movement! • Drain the fuel from float bowl and remove the bowl cover. • Remove the new cap head Allen screws in place of the OEM Phillips head screws. • Repeat above steps for other OEM main jet and pilot jet, and replace them with Baron’s main and pilot jets. • Thoroughly clean the inside of the float bowl prior to reinstalling it. • Reassemble the carburetor by reversing the order of previous steps. Use thecarburetor. • Locate the fuel mixture plug on each carburetor; it will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plug for each carburetor. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. b. Insert a self-tapping sheet metal screw into the drilled hole and remove the plug. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (2) Mikuni main jets, (2) pilot jets, (2) titanium needles, (2) clips, (8) cap head Allen screws Revision 2.0 c. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 turns. Refer to final step for assistance in fine-tuning the setting of the air/fuel adjustment screw. • Reinstall the OEM air filter assembly. • Check all vent lines, fuel lines, and linkage for any obstructions or blockage

Kawasaki VN1600 Highway Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
PREPARATION 1. Insure that the motorcycle is on flat level ground. 2. It is recommended that the motorcycle sit for at least one hour prior to installation to allow the engine to cool. During installation tight all fasteners to hold. Wait until you check all clearances and operation of the brake and shift lever to firmly tighten and torque all fasteners. INSTALLATION Right Side Highway Bar 1. Remove the front floor board bolt (M10). (14mm Socket) Figure 1. Right and Left side of Motorcycle is determined while sitting on the bike.
MAINTENANCE / CAUTION The high quality chrome finish of your National Cycle Chrome Highway Bar can be maintained with any quality chrome cleaner and / or polish applied with a soft cloth. Check hardware for tightness regularly. Never ride with loose mounting hardware. Check to be sure your Highway Bar does not contact any part of the motorcycle at a full turn left and right. Correct any problem before using the motorcycle. ©2005 National Cycle, Inc. PO Box 158, Maywood, IL60153-0158 USA 708-343-0400 / Fax: 708-343-0625 / www.nationalcycle.com / e mail: info@nationalcycle.com Page 2 of 2 10-114857-000 09/05 Install Upper “U” Bolt 2. Place “U” Bolt between the radiator and the down tube at the location shown in Figure 2. Threaded ends of “U” will face out- ward. 3. Select the right side Highway Bar. 4. Loosely install the Highway Bar at the lower mount point using the stock screw. (14mm Socket) Figure 3. While installing the Whizlock Nuts in the following Step #5 , be certain to tighten the nuts evenly, alternating left and right as you tighten. When complete you want the same amount of threads exposed on the ends of the “U” to insure the bolt does not rotate. 5. Install the upper Highway Bar with Whizlock Nuts. (1/2″ Socket) Figure 4. Orient assembly so Whizlock Nuts face outside. Firmly tighten after all clearances are checked. LEFT SIDE INSTALLATION 6. Repeat Steps 1 and 2. On the Left Side due to tight clearances between the radiator and the down tube you must locate the point where the radiator is “notched out” slightly. Figure 5. 7. Select the left side Highway Bar. 8. Repeat Steps 4 and 5.

Suzuki M 109 WINDSHIELD INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Suzuki) by admin on 18-02-2012

download
Position the motorcycle securely on its stand or a work stand. Cover the front fender and fuel tank with a cloth to avoid scratches from dropped tools. 1. Use the above diagram toidentify left from right Lower and Upper Mount Brackets. Figure 1 2. Cut each of the clamp spacers in half to make 8 pieces, each 2.5 x 1.55″. 3. Apply one spacer to the inside of each mount bracket. Figure 2 Figure 1 Figure 2 N28201 and N28202 WINDSHIELD INSTALLATION AND OWNER’S MANUAL for Suzuki®M109 Right and Left side of Motorcycle is determined while sitting on the bike. Determine left from right Upper bracket. Washer angles inboard about 5 degrees. Note, Angle distinguishes Right from Left Lower Mount Bracket 1 2 4 3 5 6 8 9 10 National Cycle, Inc. Maywood, IL 60153-0158 USA 708-343-0400 / Fax: 708-343-0625 www.nationalcycle.com / e mail:info@nationalcycle.com Page 1 of 3 10-114056-000 08/07 / Rev B. 03/08 7 3, Left Upper Bracket 4, Right Upper Bracket About 5 0 inboard angle
INSTALLATION Measurements provided for clamp location. From this point you can adjust the brackets 1″ (22mm) higher if you prefer keeping in mind, position of the front nose of windshield should have a minimum of 1/2″ (13mm) clearance from cowling . Figure 3. Right Side Lower Mount Assembly 1. Start on the Right Side of motorcycle. At the top of the fork, place one inner black clamp on the fork tube. Figure 4 2. Hook the RIGHT SIDE lower mount bracket (2) to the inside clamp. Figure 5 3. Slide assembly down fork so bottom edge of bracket is 1.75″ (44mm) from top of lower triple clamp. Adjust bracket so flat in bracket runs parallel with motorcycle. Figure 6 and 7 4. Loosely install one M8 x 16 screw. (6mm Hex Key) Figure 7 Right Side Upper Mount Assembly 5. Place the second inside black clamp on the right fork tube.

Incoming search terms:

Motorcycle Navigator ZUMO Z500/550 Owner's Manual

0

Filed Under (Tips and Review) by admin on 16-11-2010

download
GETTING STARTED Looking at Your zūmo A. Power button B. Zoom in, raise volume, or increase brightness. C. Zoom out, lower volume, or decrease brightness. D. Page button—scroll through the Map, Trip Information, Media Player, and Phone Menu pages. Press and hold to adjust brightness. E. Speak button—press to adjust volume level. Press and hold to announce voice directions. SD card slot Mini-USB port for AC adapter, USB Mass Storage mode, and updating software A B C D E MCX connector under weather cap (see page 55 ) Battery pack (see page 54 )
2 zūmo 500/550 Owner’s Manual GETTING STARTED zūmo Tips and Shortcuts • Touch and hold to quickly return to the Menu page. • Press to return to the Map page. • Touch and to see more choices. • Touch to adjust settings such as volume, brightness, language, and keyboard. Adjusting the Volume Press , and then use and to adjust the volume. For advanced volume settings, touch > Volume . Adjusting the Brightness Press and hold , and then use and to adjust the brightness. See page 44 for additional display settings. Quick Links • Finding an address: page 11 • Viewing the Map page: page 20 • Using hands-free mobile phone features: page 23 • Using the Garmin Lock™ anti- theft feature: page 10 • Listening to MP3 files: page 37 • Transferring files to your zūmo: pages 34-36 • zūmo audio options, see page 46 • Cleaning and storing your zūmo: page 55 • Mounting the zūmo in your automobile: page 47 Fill out the Product Documentation Survey. Go to www.garmin.com/ contactUs , and click Product Documentation Survey .

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

HArley Davidson Sportster Sideshots Exhaust system Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Remove the two bolts from each muffler body which Page 1 of 4 D465IN Rev. 1.0 Sportster Sideshots Exhaust system Part #26011 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: Wrenches – 9/16″ and 1/2″ Ratchet, 3/8″ drive and 9″ extension Torx sockets – T30 Sockets – 9/16″ and 1/2″ 3/16″ & 5/16″ Allen wrench 5/16″Nutdriver/flat blade screwdriver Snapring pliers attach the muffler bodies to the mounting bar and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. Note: If circlips look bent or twisted replace them with new circlips.

BMW R1100 – R850R Maintenance Guide

0

Filed Under (BMW) by admin on 27-11-2010

download
R1100 Checklist – Carl Kulow • Check alternator belt (replace 36K miles) • Adjust valves • Spark plugs (replace 12K) • Air filter (replace 12K) • Lube and adjust clutch cable • Lube front shock lower mount • Lube side and center stand • Check brake fluid (replace yearly) • Check brake pads • Check battery acid level • Fuel filter (replace 24K) • Throttle body sync • Oil and filter (replace 6K) • Check transmission fluid level (replace 12K) • Check rear wheel drive fluid level (replace 12K) • Check tires and pressure • Check all nuts and bolts • Check all air and oil hose clamps • Check all lights PARTS – TOOLS Tools Parts Misc. sockets spark plugs compressed air wrenches oil filter anti seize torque wrench air filter carb cleaner hex sockets brake pads rag hex wrenches oil – 4 qt. BMW #10 grease feeler gauges gear oil – 1 1/4 qt. flexible tubing oil filter tool alternator belt (tygon) flashlight fuel filter, o-ring, clamps measuring cylinder crush washers Mityvac -3 small = trans.drain, rear drive fill and drain digital volt meter -1 medium = oil drain heat gun -1 large = trans.fill tire change tools 5 R1100 Maintenance Steps – Carl Kulow Note: This overview section serves only as a step by step reminder for experienced workers. If you are unfamiliar with any procedure you should read the parenthetical reference article or Paul Glaves’ Routine R1100 Service Article! Note to R1100RT and R1100RS Riders: remove the side panels as described in your owners manual “Service and Technical Booklet” except RT: instead of pulling the mirror off as the manual says, you need to hold the back of the mirror (front of bike) with one hand while you hit the front outside corner of the mirror with the palm of your hand thus knocking the mirror off. Check Alternator Belt remove four bolts holding black plastic cover(4mm hex), remove cover, check belt for cracks etc., check belt tension, replace belt every 36K miles, leave cover off for valve adjustment (see Jon Diaz “Alternator Belt Adjustment”)

240 Sport Bike Swingarm Installation Instructions

0

Filed Under (Tips and Review) by admin on 02-12-2010

download
Motorcycles can be dangerous if not properly maintained and ridden safely. RC Components has no control over the usage of any of its parts. RC Components expects its customers to exercise good judgment as to the proper selection, installation, use, and maintenance of any parts. RC Components assumes no responsibility for damage or injury of any kind because of the misuse or improper application of any parts in any way by any person. RC Components expects the end user to exercise good judgment. • Before installing this kit, read through these directions completely. This will familiarize you with the way in which the parts fit together and the tools needed to complete the job. • Before performing any installation steps, disconnect the motorcycle’s battery to eliminate any possibility of electrical damage or personal injury due to a short circuit. Part Number: NSTSB240 Page 2 of 12 Materials Needed: • Hardware Kit. Kit includes (See picture below): 04-05 GSXR750-600 & 03-04 GSXR1000 Kit Inboard Brake Kit Part Number: INSTSB240 Page 3 of 12 04-05 GSXR750-600 & 03-04 GSXR1000 Kit for Stock Caliper 08 Busa Kit for Inboard Brake Part Number: INSTSB240 Page 4 of 12 05-06 GSXR 1000 Kit for Inboard Brake
Part Number: INSTSB240 Page 5 of 12 05-06 GSXR1000 Kit for Stock Caliper 99-07 Busa Kit for Inboard Brake
Part Number: INSTSB240 Page 6 of 12 99-07 Busa Kit for Stock Caliper Tools Needed: • Bike Specific Service Manual (Refer to manual for all torque specs and tools that are not specified by RC Components.) • Assorted hand tools, metric and standard sockets and wrenches. • Hoist or other means to lift bike. • Torque wrench • Loctite, and anti-seize • Chain breaker • Bike specific sockets are required for some bikes. (Refer to factory service manual). • Die grinder (for chain to frame clearance on some models) Installation Instructions 1.) Stock Component Removal To begin installing this kit it is necessary to raise the rear end of the bike using a suitable hoist. Be sure to keep the bike centered on the front wheel to keep the bike from tipping over. Once you have the bike lifted and properly secured, begin with the removal of the following stock components ( For detailed information on the removal of these parts, please consult your factory manual) : 1.) Muffler or mufflers 2.) Left side and lower body panels 3.) Voltage regulator (08 model only) 4.) Front sprocket cover 5.) Front sprocket 6.) Chain