crank rod play on shovelhead

You search Auto repair manual PDF crank rod play on shovelhead, if there are search results will appear below. If search results do not exist, please search by others keyword.



  crank rod play on shovelhead Direct Download speed 5282 Kb/s

  crank rod play on shovelhead Full Version speed 6162 Kb/s



Yamaha V-Star 1100 Custom and Classic cruisers Floorboard/ Footpeg Extension Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Start on the right (brake) side. 1) Loosen the nut at the end of the brake rod. This will allow you to unscrew the brake rod from the brake lever clevis later. 2) Pull out the cotter pin and remove the pivot pin. Unscrew the clevis 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the brake floorboard/footpeg assembly (whichever your bike has) to the frame. These bolts are torqued to 46 ft lbs, so this may be a bit difficult. 1. Loosen this nut 2. Remove the cotter pin (other side of this pivot pin) remove the pivot pin a unscrew the nut to remove the clevis nd 3. Remove these bolts When you remove the floorboard/footpeg bracket, be careful not to pull the brake switch wires loose. You may wish to cut the cable tie for more room, and then rest the bracket, with the footpeg or floorboard attached, on a short box, or block of wood, to keep it handy. Install the new brake rod, to the end of the existing brake rod. Re-install the pivot pin, and the pivot pin cotter pin. Installing the extension bar: Note that the extension bar is bolted so that it rises up in front. Use the new bolts to mount the floorboard/ footpeg bracket to the threaded holes in front. Install the Extension in the proper orientation (angled holes bolt up to the frame, with front of the bar higher than the rear – see photo) using the stock bolts for the extensions to the frame and the new bolts and washers supplied with the kit, on the forward threaded section to relocate the floorboard or footpeg bracket. The use of LocTite ® Blue here is recommended. At this point the right side Floorboard or Footpeg should be secured tightly and the brake lever hanging loose. Now install the Brake rod extension, threading the male end to the original brake rod. Don’t tighten this end yet Place the clevis over the forward most end of the brake rod extension, and threat the clevis nut onto the end of the rod. Bring the brake rod upright, to meet with the clevis at the end of the brake rod extension and replace the pivot pin. Before reinstalling the cotter pin, check the angle of the brake lever, to insure that you have the brake pedal where you want. If necessary, adjust the extension rod in or out, until you are satisfied, and then reinstall the cotter pin into the pivot pin. Check the Brake switch wire and install a new cable tie if required. Note: Due to utilizing a thicker material, 1/2″ versus 3/8″ from our competitor, the Brake rod is now positioned at a greater angle. Even with the angle, braking performance is not affected, but if you wish to bring the master cylinder in line with the brake rod, do this. Loosen the rear, and remove the front Allen bolt. Then place two washers behind the front bolt, under the bracket, and then re-install the bolts To change the angle of the brake rod, 1) loosen and remove the two master cylinder bracket Allen bolts 2) insert two washers behind the front bolt (front of the bike), behind the master cylinder bracket 3) tighten both bolts. Do not install any washers on the rear mounting hole. This will make the angle of the Brake Rod less aggressive. Step Two – Left Side For the left (Shifter) side, 1) use an open-end 10 mm wrench, to unscrew the two nuts that hold the shift rod in place. PLEASE note that one end of the shift rod has a left hand threaded nut. SAVE the nuts, as you will need them on the new longer Polished Stainless Steel Shift Rod. 2) Remove the stock shift rod. 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the shifter floorboard/footpeg assembly (whichever your bike has) to the frame.

Incoming search terms:

HARLEY DAVIDSON ALUMINUM SHIFTER LINKAGE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL 1. See Figure 1. Remove stock shifter rod (D). 2. Adjust new shifter rod in kit to match the length of the removed shifter rod by loosening locknuts (3), adjusting the length of the rod, then tightening locknuts to 20-24 ft- lbs (27-32 Nm) . 3. For models with a straight rear shifter rod lever: Discard spacer (7). Place cover (1) over the shifter rod lever (C). For models with an offset rear shifter rod lever: Place spacer (7) and cover (1) over the shifter rod lever (C). INSTALLATION 1. Apply Loctite® 243 to threads of capscrew (5) and install cap screw through the rear of the shifter rod and into the shifter rod lever. Tighten cap screw to 13-16 ft-lbs (18-22 Nm) . 2. For 1999 and later FLHT, FLHX, FLHR, and FXDWG models: Place the rod end on the outside of the shifter lever, then apply Loctite® 243 to the threads of capscrew (5). Attach the front of the shifter rod (6) to the shifter lever with capscrew (5) and acorn nut (4) (with acorn nut facing out). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm) . For all models except 1999 and later FLHT, FLHX, FLHR, and FXDWG: Place the rod end on the inside of the shifter lever then apply Loctite® 243 to the threads of cap screw (5). Attach the front of the shifter rod (6) to the shifter lever with cap screw and acorn nut (4). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm)

SUSPENSION SERVICE TOOLS/ FORK DAMPER ROD BLEED TOOL

0

Filed Under (Tips and Review) by admin on 30-11-2010

download
33 SHOP EQUIPMENT & TOOLS SUSPENSION SERVICE TOOLS K&L FORK TUBE U-BLOCKS Precision machined from billet aluminum, these quality three piece sets are a handy, accurate and safe way to straighten and check fork tubes. 35-9411 36mm (for 33 thru 36mm tubes) 35-9412 40mm (for 37 thru 40mm tubes) 35-9413 43mm (for 41 thru 43mm tubes) 35-9414 46mm (for 44 thru 46mm tubes) 35-1964 35-8579 35-7995 DAMPER ROD HOLDERS Holds damper rod when disassembling forks. 35-8578 Yamaha front forks, 43mm Kayaba YZ125/250 (1988) YZ490 (88-90) 35-8579 Yamaha YZ125/250 with UD(upside down) forks FORK DAMPER ROD TOOLS Sold each. 35-7995 Combination Fork Damper Tool Designed to hold the damper rod during assembly & disassembly of Honda XR400′s or Suzuki DR-Z400S. One end features spanner type prongs for the XR400 and the other a 27mm hex for Suzuki. 35-1964 Combination Damper Rod Fork Tool Designed for assembly and disassembly of most inverted Kayaba and Showa 41mm, 43mm, 46, and 47mm forks. Use one end for Kayaba forks and the other for Showa forks. (not required for 91-92 Honda CR models) ROD HOLDER Double sided damper rod holder. Works on Kayaba U.D (upside down) 41mm forks. 35-8580 Yamaha YZ125/250Amodels (89-90) FRONT FORK CAP SOCKET Designed to remove and install Yamaha front fork caps with female hex head. Sold each. 35-8571 14mm female socket 35-8573 19mm female socket FORK DAMPER ROD HOLDERS Holds damper rod when disassembling and assembling front forks. 35-8576 Use for Yamaha 43mm Kayaba forks, 30mm hex YZ125 (84-87), YZ250 (81-87) IT250 (1983) YZ490 (82-87) 35-8577 Use for Yamaha 38mm Kayaba forks, 24mm hex YZ125 (81-83), IT175 (82-83), IT250 (81-82) YZ250 (77-80), YZ400 (77-79), IT465 (81-82) FORK CAP WRENCH Designed to remove the front fork caps on late model Honda CR’s and Suzuki RM’s. Can also be used for adjusting compression. One end of wrench is 49mm, the other is 50mm. Sold each. 35-7803 Fork Cap Wrench 35-8576 35-8577 35-8571 35-8573 6 Point Hex 35-8578

Incoming search terms:

HARLEY DAVIDSON SPORTSTER ALUMINUM SHIFT LINKAGE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION 1. See Figure 1. Remove stock capscrews (4) and stock shifter rod (2). Discard stock capscrews. 2. See Figure 2 and Table 2. Loosen the lock nuts (5) and turn the rod ends on the new aluminum shifter rod (1) to match the length of the stock shifter rod. 3. See Figure 2 and Table 2. Slide longer capscrew (3) through the front rod end of new shifter rod (1). Place rod on the outside of the lever assembly. Thread capscrew (3) into the lever assembly. 4. Slide shorter capscrew (2) through the rear rod end of new shifter rod (1). Place rod on the outside of the transmission shift lever. Thread capscrew (2) into the transmission shift lever. 5. Tighten capscrews to 10-15 ft-lbs (13.6-20.3 N-m) . 6. Firmly tighten the lock nuts (5) against the rod ends to 20- 24 ft-lbs (27.1-32.5 Nm) . 1 4 2 4 3 is05394 1. Lever assembly 2. Shifter rod 3. Transmission shift lever 4. Capscrew Figure 1. Shift Linkage Components

BMW K1100 RS/ RT/ LT ABS 2 Electronic Cruise Control Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The carburettor cable and spool are installed and the other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location. This is because flexing the cable does effect the free play. It is shown at this stage in these diagrams to improve clarity. After this adjustment is performed, the carburettor cable adjustment MUST NOT BE MOVED. All future adjustments of free play in the throttle must be performed on the throttle cable from the throttle grip. If incorrect free play in this cable is suspected due to inconsistent cruise operation or because of inconsistent idle speed, the adjusters on the throttle cable from the hand grip must be backed all the way off to give as much free play as possible. If this does not result in AT LEAST 5mm of free play in the throttle cable, the throttle cable must be removed from the hand grip or CIU before adjustment of the carburettor cable is attempted. This is crucial because the amount of free play in the throttle cable also effects the apparent free play in the carburettor cable.

KAWASAKI Z1000 GTR Electronic Cruise Control Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The dual spool and carburettor cable are installed. The carburettor cable is attached to the lower groove in the dual spool. The other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location. This is because flexing the cable affects the free play. It is shown at this stage in these diagrams to improve clarity. After this adjustment is performed, the carburettor cable adjustment MUST NOT BE MOVED. All future adjustments of free play in the throttle must be performed on the throttle cable from the throttle grip. If incorrect free play in the carburettor cable is suspected due to inconsistent cruise operation or because of inconsistent idle speed, the adjusters on the throttle cable from the hand grip must be backed all the way off to give as much free play as possible. If this does not result in AT LEAST 5mm of free play in the throttle cable, the throttle cable must be removed from the hand grip or CIU before adjustment of the carburettor cable is attempted. This is crucial because the amount of free play in the throttle cable also affects the apparent free play in the carburettor cable

S&S Connecting Rods Installation Instructions

0

Filed Under (S&S) by admin on 29-10-2010

download
1. Female rod crankpin end to mainshaft nuts – .030″ minimum clearance recommended. A. Install sprocket shaft and crankpin in driveside flywheel. Snug nuts only. Do not torque to final specs. B. Slide connecting rods and bearings over crankpin. C. Rotate rods on crankpin, and observe clearance between rod and sprocket shaft nut. D. If additional clearance is needed, remove material from sprocket shaft nut. Do not remove material from connecting rod. E. Repeat procedure for camside flywheel and pinion shaft. 2. Female rod crankpin end to inner flywheel rim – .060″ clearance recommended. A. While checking female rod to mainshaft clearance, observe clearance between crankpin end of female rod and rim of both flywheels. B. If additional clearance is required, remove material from flywheel at point of contact. Do not remove material from connecting rod. 3. Wristpin end of both female and male rods to flywheel edge -.060″ minimum clearance recommended. A. While checking female rod to mainshaft clearance, observe clearance between wristpin end of both rods and rim of both flywheels. B. If additional clearance is required, remove material from flywheel at point of contact. Do not remove material from connecting rod. 4. Wristpin end to crankcase and cylinder – .060″ is recommended in these areas. A. With the camside flywheel and rods mocked up, install the assembly in the right crankcase half with pistons (less rings) and cylinders in place. B. Rotate flywheel through one full revolution and check for rod to crankcase and cylinder spigot contact on both the front and rear of each cylinder. C. File or grind crankcase or cylinder spigot as needed to achieve .060″ clearance. Do not remove morematerial than needed. D. Repeat for left crankcase half. NOTE: Whenever clearancing is performed in any of these areas, do not remove any material from the connecting rods as clearancing on the rods may unnecessarily weaken them. Make adjustments to the point of contact on the mainshaft nut, flywheel rim, crankcase, cylinder spigot, etc. Connecting rods weakened by clearancing may fail causing serious engine damage.

Incoming search terms:

Harley Davidson Five Speed Transmissions Hydraulic Clutch Modification

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Hydraulic Clutch Modification for Harley Davidson With Champion Reverse Gear 1 1.1 Install Reverse Gear Assembly to gearbox. 1.2 Remove clutch cover (left side). 1.3 Remove Release Plate (clutch adjustment) and Push Rods. 1.4 Install Hydraulic Clutch Release Cover with supplied spacer and two gaskets. 1.5 Bleed clutch system. NOTE: When bleeding clutch system, lever feel will become hard, do not force lever because piston is at end of travel.(Continue Bleeding) 2 2.1 Install Push Rod. 2.2 Push the rod into clutch assembly to force hydraulic piston to its start position. Push the rod hard until the clutch cylinder is fully compressed. This is the start position. 2.3 Install Hydraulic Clutch Throw-Out Bearing Holder and bearing to push rod. Do not install circlip at this time. 2.4 If the throw-out bearing holder does not fully seat into the Pressure Plate (Figure 2.4), proceed to step 2.5. If shaft is too short then use throw-out bearing holder from Champion Reverse Gear Kit, skip next step and proceed to 3.0 2.5 Measure distance between bearing holder and pressure plate (ensure that push rod is pushed in) Figure 2.4 2.6 Remove bearing holder and push rod, reinstall bearing holder until seated (without push rod). Measure distance from pressure plate to bearing holder. Figure 2.6 2.7 Add measurements taken in steps 2.5 and 2.6 2.8 Add 0.090″ to total of step 2.7 (allowance for clutch plate wear). Measurement should be approximately 1/8″. 2.9 Measure push rod length. 2.10 Subtract measurement of step 2.8 from measurement of step 2.9 (push rod length). This measurement represents the amount of material to be removed from ball end of push rod. (Step 2.11)

Yamaha Roadliner And Stratoliners Brake Pedal Relocation Kit

0

Filed Under (Yamaha) by admin on 27-12-2010

download
1. This kit replaces the original rear brake actuating rod that connects the pedal to the master cylinder (see photo 1A) and the brake light switch spring (see photo 1B). Remove the two allen screws which attach the switches mounting plate to the frame (1C). Remove the spring. 2. Remove the cotter pin and washer from the forward end of the rod where it connects to the brake pedal (photo2A). Slide the rod over off of the brake pedal. Unscrew the rod from the threaded stud on the master cylinder. 3. Thread the new rod onto the stud until the end of the stud appears in the middle of the small sight hole that is cross drilled thru the rod (1D). Place the forward end of the rod back onto the brake pedal. Next check the distance between the bottom of the brake pedal and the top of the floorboard, this should be approximately 1 ¾”. If not, slide the rod off the pedal and thread it in or out to adjust the pedal height. With the rod on the pedal re-install the washer and cotter pin (Note: the cotter pin should go into the hole from the top down) then bend the cotter pin open. 4. Replace the brake light spring with the new one supplied. (Pushing down on the switches rubber cover will push the pin out). Re-install the switch bracket. Turn on the ignition and adjust the threaded collar on the brake switch so that the brake light comes on just as you feel some resistance when pushing on the pedal (when the brakes begin to drag).

Indian Rocker Arm End Play Rear Cylinder/ Front Cylinder Installation

0

Filed Under (Indian) by admin on 12-11-2010

download
Rear Cylinder 1Rotate the engine so that the rear piston is at Top Dead Center (TDC), compression stroke, so no load is on the valves. 2Using a 3/16″ allen wrench, remove the four screws securing the rear cylinder rocker cover. 3Remove the cover and inspect both O-ring seals. Discard if damaged or worn. 4Push both rocker arms towards the valve end support bracket (A) and using a feeler gauge check the gap between the rocker arms and the pushrod end support bracket (B). NOTE: The Rocker arm end play specification should be between 0.003″ to 0.012″. 5 Compare the measurement to the specification an determine whether adjustment is necessary. If the end play is within specification, adjustment will not be required. Refit the rocker cover (instructions 14 to 15) and carry out the same inspection on the front cylinder . If the measurement is outside the specification, adjustment will be required and shimming will be necessary (follow the remainder of these instructions). Adjustment 6Using a 1/4″ allen wrench remove the 4 screws securing the rocker shaft assembly.Refit the LH support bracket and reposition the complete assembly on the rocker base. Make sure that the three dowels are in place and the slots in the rocker shafts are properly aligned with the mounting screw holes in the RH support bracket. 11Clean the threads of the 4 support bracket screws and apply Blue Loctite to the first 4 threads. 12Fit the 1-3/4″ screws into the LH support bracket (A) and the 2″ screws to the RH bracket (B). Torque all screws in cross pattern to 16-20 foot-pounds. CAUTION: The rear piston must be at TDC, compression stroke, when tightening the support bracket screws. 13Re-check the rocker end play to ensure it is within specifica- tion. 13Lubricate the two O-rings with clean engine oil and refit them in the grooves in the rocker base. 14Refit the rocker cover.

Incoming search terms: