crewline jack

You search Auto repair manual PDF crewline jack, if there are search results will appear below. If search results do not exist, please search by others keyword.



  crewline jack Direct Download speed 5282 Kb/s

  crewline jack Full Version speed 6162 Kb/s



JMJ-1500 Motorcycle/ ATV Jack OWNER'S MANUAL

0

Filed Under (Tips and Review) by admin on 23-11-2010

download
1. Secure hydraulic ram (20) to the lift base (4) with two screws (21 & 21A). 2. Insert foot pedal assembly (19) into hole over pump piston and secure it with screw (19A) and flat washer (19B). 3. Raise lifting frame (17) to the proper height and align holes in the hydraulic ram (20) with the holes in the middle of the lifting frame. Secure ram to lifting frame with clevis pin (18) and R-pin (22) provided. 4. Place the spring (18A) in position between the clevis pin (18) and screw (18B). Operation 1. Before each use, visually inspect jack for abnormal conditions such as cracked welds, leaks, and damaged, loose or missing parts. 2. To raise the jack, center it directly below object to be lifted. Pump the foot pedal (19) slowly, making sure saddle takes up weight firmly and centrally. Check positioning under slight load to confirm load is centered on jack and load will not shift or slip. 3. Continue to raise jack slowly by pumping foot pedal to reach desired height. 4. Once desired height has been reached, raise safety arms (8) or built-in jack stands, to engage in raised tabs on lift base (4). SLOWLY press pump release foot pedal (23) to allow load to lower and rest on safety arms. 5. Secure load to jack with hold down straps (not included). Fasten hold down straps to steel loops on front and rear of frame. 6. To transport jack under load, lower jack with foot pedal (23) SLOWLY to the lowest position and always use the tow handle (1). Use EXTREME CAUTION when transporting jack under load! 7. To lower jack, raise load slightly with foot pedal (19) and disengage safety arms (8) from lift base (4). Press pump release foot pedal (23) until jack has been completely lowered. Unfasten hold down straps and remove jack from vehicle. Maintenance Adding/Changing Hydraulic Oil: Maintain oil at full level. For best performance and long life, replace hydraulic fluid once a year. 1. With saddle (10) lowered completely, remove oil plug located in hydraulic ram (20). 2. Drain fluid into appropriate container. Always dispose of oil in accordance with local regulations. 3. Use only good quality hydraulic jack oil. Fill until oil is level with inner cylinder as seen from the opening of the filler hole. Reinstall oil plug. Lubricate the jack as indicated on a regular basis with 30W oil. 1. Saddle and linkage on foot pedals and all moving and pivoting parts. 2. Front and rear lifting arms. Always store jack in the fully lowered position. Inspect jack annually for defective parts, missing safety labels or decals. If jack is found to be damaged or defective in any way, or operates abnormally, it shall be removed from service until repaired

Incoming search terms:

KTM 3V TURBO DRIVE MODEL 9808T KNEE FEED Installation and Removal Manual

0

Filed Under (KTM) by admin on 28-01-2012

download
Gather together the following items that you will need to complete this installation. a) lathe b) 3/8″ electric hand drill c) 9/32″ diameter transfer punch SERVO Turbo Drive Model 9808T Page 2 d) .4375 drill, 3/16″ drill, #7 drill e) 1/4-20 tap f) 3/4″ socket wrench g) set of inch hex wrenches h) clean shop rag Step 2: Clean the power feed mounting area completely. Step 3: Remove the drive clutch nut and the drive clutch from the elevating jack shaft. Step 4: Remove the dial nut, dial, and dial carrier. Keep the dial for reuse later. Step 5: Remove the existing bearing retainer. Keep the screws for reuse later. Step 6: Pull jack shaft out of knee. Hold inboard end up while removing to avoid damage to the pinion gear. Step 7: Press the bearing off the jack shaft. Step 8: Drill and ream the end of the jack shaft .4375″ diameter by 13/16″ deep. The .4375″ dia. must be concentric to the shaft O.D. within .002″ T.I.R. Chamfer 1/32″ x 1/2″ diameter. For best results, machining should be done in a lathe. Step 9: Place the shaft extension #6975 into the end of the jack shaft. Finish drill 3/16″ diameter through the shaft and pin the extension with the 3/16″ diameter x 5/8″ long roll pin. File smooth. Step 10: Reassemble and replace the jack shaft in the machine. Step 11: Replace the existing bearing retainer with #57904 retainer provided. Secure using existing screws. Step 12: Slip spacer #5426 and bearing race #1616 onto the jack shaft. Slide the adaptor #0771 over the bearing race and locate against front of the knee.

Incoming search terms:

Kawasaki 650/360 Prairie Lift Kit Installation and removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Place jack under center of ATV front end and lift until front wheels clear the ground. Be careful to support ATV properly so that it is securely supported but so that A-arms and shocks can droop to full extension. 2) Remove front wheels. 3) Remove or loosen front plastic. 4) Remove C-clip and nut at the top of the strut. 5) Screw bracket “A” on top of strut to the same torque specifications as the nut. 6) Place the top adapter “A” through the top of the strut mount, and screw the original nut on the top of bracket “A” securing it to the strut mount. Tighten this nut to the required manufacturer specifications and replace the factory C-clip. 7) Repeat the procedure for the other side. 8) Install the wheels, torque wheel lug nuts to manufacturer’s specifications, lower and remove jack. Check for clearance problems or misalignment. Rear Lift 1) Place jack under ATV at the rear of the bottom skid plate and lift until the weight is off of the suspension. Be careful to secure the ATV properly so as not to fall off the jack. 2) Remove the bottom of the shock from the shock mount on the axle. 3) After removing the shock, jack the ATV up 1″-2″ further. 4) Place Bracket “B” between the shock and shock mount with the notched out ends facing downward. Insert stock bolt to secure bracket “B” to the shock mount and the shock. Fasten nut. 5) Insert the new 12x75mm Bolt to the top of bracket “B” and the shock eyelet and secure with a new 12mm nut. 6) Tighten all nuts and bolts to manufacturer’s torque specifications. 7) Install the wheels, torque wheel lug nuts to manufacturer’s specifications, lower and remove jack. Check for clearance problems or misalignment.

Triumph America Installation Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
Secure motorcycle in an upright position. 2) Remove center stand 3) Remove saddle bags (if applicable) 4) Attach bracket A to center stand mounting point on motorcycle 5) Attach bracket D (left) / E (right) to rear fender sub-frame using new bolts provided. It may be necessary to reattach saddle bags at this point 6) Attach bracket F (left) / G (right) to rear of brackets D/E. 7) Attach bottom of brackets F/G to rear hitch plate. 8) Attach bracket B (left) / C (right) to bottom of forward hitch arms. Attach other end of B/C to top of bracket A. 9) Ensure hitch is square with motorcycle and tighten all bolts. Receiver Hitch Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded leveling stand tab on bracket A and adjust leveling jack bolt out. 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket A and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

Yamaha V-Star 1100 InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 05-01-2012

download
Receiver Hitch Installation y Install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove saddle bags (if applicable) 4) Attach bracket G to underside of motorcycle frame with U-bolts provided. 5) Attach bracket C (left) and bracket D (right) to the two rear fender side attachment bolts between fender and chrome side rail. Use new bolts provided. ( reattach saddle bags now if applicable) 6) Attach bracket E (left) and bracket F (right) to the outside of the rear holes on brackets C and D . Bolt inserts from inside of brackets C and D . 7) Attach bottom of brackets E and F to rear plate on receiver hitch. 8) Attach rear of brackets A and B to TOP of forward arms on receiver hitch. 9) Attach front of brackets A and B to TOP of bracket G 10) Ensure hitch is square on motorcycle and tighten all bolts.
Installation Diagrams
Leveling stand screw jack installation 1) Thread right side screw jack into threaded area on bracket B sand adjust leveling jack bolt out. 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket A and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

650 Yamaha V-Star InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove rear foot pegs and bolts 3) Attach bracket A (left) and bracket B (right) to the inside of the rear foot peg bracket and reattach rear foot pegs using new bolts provided. 4) Attach front of bracket C (left) and bracket D (right) to bottom of brackets A and B 5) Attach bracket E (left) and bracket F (right) to two rear fender attachment bolts using new bolts provided 6) Attach brackets G and H to rear of brackets E and F 7) Attach bottom of brackets G and H to hitch plate. 8) Attach rear of brackets C and D to TOP of forward hitch arms. 9) Tighten all bolts. Installation Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded hole on bracket D 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket C and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

Kawasaki Vulcan 500 Receiver Hitch Installation Manual

0

Filed Under (Kawasaki) by admin on 06-05-2012

download
1) Place motorcycle on its side stand on a firm level surface. 2) Remove saddlebags if any. 3) Remove rear riders pegs. 4) Attach front of bracket A (left side) and bracket B (right side) between rear footpeg motorcycle bracket and rear footpeg. Use new bolt provided (Bolt assortment included to accommodate some accessories) 5) Attach bracket E (left side) and bracket F (right side) to two rear fender attachment bolts. Use new bolts provided. (Bolt assortment included to accommodate some accessories) 6) Attach bracket C (left side) and bracket D (right side) to brackets E and F and to second holes on rear of hitch. 7) Attach rear of brackets A and B to BOTTOM of hitch arms 8) Tighten all bolts. Receiver hitch diagram Leveling stand screw jack installation After hitch is installed, install leveling stand screw jacks to hold motorcycle in an upright and level position in order to install or remove InstaTrike. 1) Thread right side screw jack into leveling stand bracket on bracket B and adjust leveling jack bolt out until motorcycle will be level against it. 2) Push motorcycle over from left side until right screw jack is touching floor.

Incoming search terms:

TOYOTA TACOMA 2005 SPARE TIRE LOCK Procedure

0

Filed Under (Toyota Manuals) by admin on 21-10-2011

download
1. Lower Spare Tire. (a) Lower spare tire using hooked jack handle supplied in the vehicle tool kit. 2. Install Spare Tire Lock. (a) Install the spare tire lock assembly on the lowering screw by lining up the cross pin in the lock with the slot in the lowering screw. (b) Tap lock in place with a rubber mallet until it is fully seated. (Pull on lock to ensure attachment.) (c) Install adapter shroud (protects cable and spring) using slotted washer. (See Fig. 2-1) 3. Install Key on Hooked Jack Handle. (a) Install key on hooked jack handle, pressing the jack handle into the slot in the key until the clip snaps in place

HT1500 GOLD WING CONVERSION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 16-12-2010

download
Removal of Bike parts: Remove the following parts following the factory manual: s ide covers, p assenger foot rests, e xhaust covers, seat, t our pack, s addlebags, b attery and b ox, r ear tire, b rake line ( at rubber hose near swing arm pivot ), s hocks ( air compressor line is disconnected at shock, and stays with compressor) , S wingarm and d riveshaft (reverse box may stay connected, just pull out to side ), m ufflers, and h elmet locks. Preparation: Cut-off the saddlebag support tubes where the vertical tube meets the angled tube in the front and back. All you want left is the tour pack support. Loosen tour pack support at bottom bolts, remove top bolts, and then lift up a little. This allows the body to go under the support. If you have the fuel tank: Secure the two black control boxes, facing each other, one on top of the other. Secure to frame using the green ground wire hole at center of frame. Use the 2 ¼” spacer tube and long screw provided to hold them together. If no fuel tank: leave rear half of fender in place Install air-compressor relocation bracket (1 ½” x 4″ w/ 3 holes) and remount compressor. After mounting, secure the compressor to the bracket with a wire tie Install suspension: See brake amendment for master cylinder prep Install machined studs in the swing arm pivot hole with some blue Locktite on them. This provides a 5/8″ stud on the side of the frame for the suspension side plates. Screw in until flush with frame. Remove the 6mm bolts from the exhaust heat shield on the outside of the frame rail. Install the shock replacement bars on the top shock stud and re-install bolts, leave bars hanging loose for now. Put the suspension on a floor jack and roll up to the bike. (note: once forward all the way, jack up to meet the studs.) Spread the chassis plates over the studs and start the nuts. Be careful not to damage the threads on the machined studs. Jack up the rear to align the shock replacement bars, slip in the bolts. Install 8mm x 40mm bolts and ¾” spacers to crash bar tabs on frame with spacer. Tighten the front stud nuts, crash bar tab bolts, and shock replacement bars

Incoming search terms: