crf chassis crack weld

You search Auto repair manual PDF crf chassis crack weld, if there are search results will appear below. If search results do not exist, please search by others keyword.





2003-2004 HONDA GL 1800/A Frame Weld Safety Recall

0

Filed Under (Honda) by admin on 15-12-2010

download
there is no punch mark on the VIN plate as specified in this Service Bulletin, proceed to the REPAIR PROCEDURE section of this Service Bulletin. IMPORTANT: Due to the complexity of this campaign it is imperative that you check iN and your Dealer Responsibility Report before you begin repairs. If iN or your Dealer Responsibility Report indicate the Safety Recall has been performed, but you confirm the unit is not punched and the repair has actually been done (by inspecting the weld), please contact the Warranty HelpLine at (800) 421-1900, option 7. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510)  Frame Weld Inspection Chart (S0516) You MUST provide your TIG welder with the following items:  2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511)  2002-2003 GL1800/A Frame Weld Safety Recall Cracked Weld Repair Manual (S0515) Welding Template Box (S0512) All of the above items were shipped to you with Service Bulletin GL1800 #14. If you need additional copies of these materials, you may order them from Resolve at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. DISASSEMBLY OVERVIEW You will be removing the following components from the vehicle as instructed in the Dealer Booklet : Handlebar weights Rear view mirrors Swingarm pivot covers Rider foot pegs Seat Side covers/Engine side covers Fairing pockets Fairing molding Meter panel Top shelter Battery Fuel tank Main wiring harness ground Front lower fairing Front exhaust pipe protector Muffler/exhaust pipe Antenna Whip(s) Coolant reserve tank Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: Before you send the motorcycle to the welder, you MUST check for lower crossmember frame weld cracks.  If your inspection reveals no cracks in or on either the Left or Right lower cross- member frame welds, proceed to the REPAIR PROCEDURE OVERVIEW section of this Service Bulletin.  If your inspection identifies a crack or cracks in or on either the Left or Right lower crossmember frame welds, perform the following procedure: Place the grinding template (S0512) on the crossmember. Using a suitable felt marker, draw a line on the weld with the crack, drawing the line along the entire edge of the the template (this line will be 89 mm long). If the crack falls within the length of this line (89 mm) , prepare the motorcycle for welding per the Dealer Procedures and advise the welder to use the Cracked Weld Repair Manual (S0515). After the bike has returned from the welder, prepare the frame and re-assemble the motorcycle per the Dealer Procedures . Then, proceed

Incoming search terms:

2002-2003 Honda GL1800/ A Frame Weld REPAIR PROCEDURE OVERVIEW

0

Filed Under (Honda) by admin on 14-12-2010

download
If your inspection identifies a crack or cracks in or on either Left or Right lower crossmember frame welds, STOP – call your DSM or TechLine for further instructions. • If your inspection reveals no cracks, proceed to REPAIR PROCEDURE. NOTE: Verification of repair can also be found in the Dealer Responsibility Report and on the Honda Interactive Network (iN). If you have any questions about verification, please contact TechLine before proceeding. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510) • Frame Weld Inspection Chart (S0513) You MUST provide your TIG welder with the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • Welding Template Box (S0512) All of the above items were shipped to you with this Service Bulletin. If you need additional copies of the Dealer Booklet , Welding Manual , Welding Template Box , or Frame Weld Inspection Chart , you may order them at no cost from DDS at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. Disassembly Overview You will be removing the following components from the vehicle as instructed in the Dealer Booklet : • Handlebar weights • Rear view mirrors • Swingarm pivot covers • Rider foot pegs • Seat • Side covers/Engine side covers • Fairing pockets • Fairing molding • Meter panel • Top shelter • Battery • Fuel tank • Main wiring harness ground • Front lower fairing • Front exhaust pipe protector • Muffler/exhaust pipe • Antenna Whip(s) • Coolant reserve tank • Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: You MUST cover the following with RED duct tape for welder identification pur- poses: • Negative (-) and positive (+) battery cables • Fuel return hose end • Fuel feed hose end • Main wiring harness ground • Alternator • Exhaust ports Welding Overview A qualified TIG welder will weld the frame following the procedures in the 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual . Re-assembly Overview You will be inspecting the new TIG welds, painting the frame, and re-assembling the vehicle as detailed in the Dealer Booklet and Frame Weld Inspection Chart (S0513)

Incoming search terms:

2001-2002 Honda GL1800/A Frame Weld Inspection PROCEDURE

0

Filed Under (Honda) by admin on 22-04-2011

download
IMPORTANT: During these procedures you may be using and referring to the following materials, originally sent to you with Service Bulletin GL1800 #14. • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Procedures (S0510) • Frame Weld Inspection Chart (S0516) • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • 2002-2003 GL1800/A Frame Weld Safety Recall Cracked Weld Repair Manual (S0515) • Welding Template Box (S0512)If you need additional copies of these materi- als you may order them at no cost from Resolve at (440) 572-0725. 1. Position the motorcycle on a firm, level surface, in an area where there is enough room to safely lay it on its left side. 2. Remove the left side mirror by following the nstructions on page 2-7 of the Service Manual. 3. Remove the left engine side cover by following the nstructions on page 2-5 of the Service Manual. 4. Remove the antenna whip(s). 5. Remove the coolant reserve tank by fol- lowing the instructions on page 6-7 of the Service Manual. 6. Place thick, non-abrasive padding (such as furniture blankets) on the ground to protect the motorcycle when you lay it on its side. 7. Lock the handlebars to the RIGHT, using the ignition key. 8. Using two people, gently lay the motor- cycle down on its LEFT side on the pad- ding. The motorcycle will first rest on the wheels and left engine and saddlebag guards. Continue to lean the motorcycle to the left until it rests on the left handlebar end and left engine and saddlebag guards. The motorcycle should be laying on the padding, with its engine guard, saddlebag guard, and handlebar end resting on the padding – no painted parts should be con- tacting the padding. 9. Clean the frame crossmember with acetone. 10. Draw a line on each side of the grinding template (S0512) 30 mm from the for- ward edge, stopping  between the two arrows, as illustrated below. 11. Put this template on the frame and, using a fine-tipped felt marker (such as a Sharpie), draw a 30 mm line on both crossmember welds. Start this line at the forward edge of the grinding template and stop between the two arrows as shown in the illustration on the next page.Now remove the grinding template

Honda CRF/ XR50 Carburetor Kits, Air Filters INSTALLATION AND REMOVAL

0

Filed Under (Honda) by admin on 18-12-2011

download
The CRF/XR50 engineers never intended “large” people to be competitively thrashing their design. As a result, failed frames are becoming quite common at the track. Laid-out forks, tweaked, ill-functioning suspensions and bent frames are symptoms we’ve all witnessed. This CRF/XR50 frame kit addresses all these problems with not only a stronger framer but also with added knee-to-bar clearance for taller riders.. Features: • Heat-treated chromoly steel frame • TIG welded • Fully gusseted • Thicker-walled main tube that is also larger in diameter • Conservatively estimated at 4 times stronger than the stock unit • Race legal open cradle configuration, but with fully closed loop rear sub frame under the seat for added strength and safety • Stronger swing arm pivot area prevents wallowing • Frame is 1″ longer than stock, resulting in greatly enhanced handling characteristics This Chromoly 1″ longer frame with chromoly removable subframe is the off the hook! It features a detachable chromoly subframe with all hardware as well as a 1″ rise in gas tank and seat height for more more leg room and to allow bigger carburetor modifications. Extended frame also provides: • Much needed knee-to-bar clearance • Improved rider position • Better Center of Gravity • Better control Features: • Heat-treated chromoly steel frame • TIG welded • Fully gusseted • Thicker-walled main tube that is also larger in diameter • Conservatively estimated at 4 times stronger than the stock unit • Race legal open cradle configuration, but with fully closed loop rear sub frame under the seat for added strength and safety • Stronger swing arm pivot area prevents wallowing • Frame is 1″ longer than stock, resulting in greatly enhanced handling characteristics • Gas Tank is raised 1″ for added clearance

Incoming search terms:

HONDA 2008 CRF 450 F SLIP-ON EXHAUST SYSTEM REPAIR MANUALS

0

Filed Under (Honda) by admin on 25-12-2011

download
The Akrapovic Slip-On system is designed for recreational Honda CRF 450 enthusiasts. It delivers an excellent combination of quality, performance, visual enhancement, easy installation and affordability. The Akrapovic Slip-On is designed for two markets; in the US it is available with an approved spark arrester, and for the EU and other non-US markets it comes with a noise damper. PERFORMANCE Measurements of the Akrapovic SLIP-ON system on the HONDA CRF 450 R (with muffler insert): Power & Torque: Up to 5600 rpm the Akrapovic Slip-On essentially follows the stock power and torque curves. It shows its true colors above that range, where it delivers significant increases to both power and torque. Max. increased power of 2.8 HP was measured at 6600 rpm. At the top of the rpm range the Akrapovic curves again follow the stock power and torque curves. CONFIGURATION The system is composed of a flared stainless steel link pipe which is welded to the muffler. It is attached to the stock header assembly with a sleeve joint secured with a metal clamp. The muffler is the offroad design with a titanium outer sleeve, and stainless steel inlet cap, outlet cap and inner perforation. The muffler is attached to the frame using an Akrapovic carbon-fiber clamp. In the US the system is available with an approved spark arrester, and for the EU and other non-US markets it comes with a standard noise damper

Incoming search terms:

Suzuki GSX1400FE CHASSIS REMOVAL AND INSTALLATION

0

Filed Under (Suzuki) by admin on 17-12-2010

download
REMOVAL SEAT Remove the seat with the ignition key. FRAM COVERS Remove the seat. (*Above) Remove the frame cover mounting secrews (left and right sides). Remove the frame covers by pulling on the hooked parts. PILLION RIDER HANDLE Remove the pillion rider handle by removing the pillion rider handle mounting bolts. SEAT TAIL COVER Remove the seat. (*Above) Remove the pillion rider handle. (*Above) Remove the seat tail cover mounting screws. : hooked part 6-4 CHASSIS Remove the fasteners.(*6-5) Disconnect the seat lock cable A. Disconnect the brake light/taillight lead wire coupler. Remove the seat tail cover. REMOUNTING Remount the seat, frame covers, pillion rider handle and seat tail cover in the reverse order of removal. www.GSX1400FE.co.uk
CHASSIS 6-5 FASTENER REMOVAL AND REINSTALLATION FASTENER REMOVAL Depress the head of fasteners center piece 1. Pull out the fastener. INSTALLATION Let the center piece stick out toward the head so that the pawls 2 close. Insert the fastener into the installation hole. NOTE: To prevent the pawl 2 from damage, insert the fastener all the way into the installation hole. Push in the head of center piece until it becomes flush with the fastener outside face.

HONDA 2005 CRF 50 F AKRAPOVIC RACING EXHAUST SYSTEM INSTALLATION

0

Filed Under (Honda) by admin on 03-12-2011

download
put the motorcycle on a side standn 2. unscrew and remove the bolts from the rear and front part of the motorcycle cowling (Figure 1, 2, 3, 4) m3. remove complete cowling together with the seat (Figure 5) 4. unscrew the bolt from the metal bracket for the muffler (Figure 6) 5. unscrew and remove the bolts on the flange of the header tube (Figure 7) 6. remove the stock exhaust system (Figure 8) 7. remove the stock heat shield (Figure 9) INSTALLATION OF THE AKRAPOVIC RACING EXHAUST SYSTEM installing the header tube: 1. attach the stock heat shield onto the Akrapovic header tube (Figure 10, 11) 2. set up the Akrapovic header tube and hand tighten the flange; use stock gasket; (Figure 12, 13) 3. make sure the header tube is not touching the engine or frame installing the muffler:
1. correctly position the muffler and slide it onto the header tube (Figure 14) 2. attach the spring at the muffler – header tube joint igure 15) 3. attach the muffler to the chassis hanging bracket – use the bolt, washer and spacers supplied in the Akrapovic kit. Do not
fully tighten. Make sure the additional parts from the Akrapovic kit are correctly installed. (Figure 16, 17) 4. make sure the header tube is not touching the engine or frame final installation: 1. tighten fully the bolts of the muffler metal bracket and header tube flange (Figure 18, 19) 2. reattach the complete cowling (Figure 20, 21, 22, 23, 24) 3. clean grease spots: a. muffler – titanium outer sleeve: use a soft cloth sprayed with a multi-purpose spray lubricant (WD-40 or equivalent) b. stainless steel header tube: use a soft cloth sprayed with a contact cleaner, then wipe with a soft dry cloth Cleaning will prevent spots from burning onto the surface. Do not use aggressive chemical cleaners, because they can damage the sticker. 4. position of the correctly installed Akrapovic RACING system (Figure 25)
5. Check the operation of the brakes and suspension. Make sure all the bolts are sufficiently tightened. In case the exhaust system touches the cowling or other parts repeat the adjustment of the exhaust system or contact your authorized dealer

Incoming search terms:

MOTOSCAN II MOTOSCANII Motorcycle chassis dynamometer

0

Filed Under (Tips and Review) by admin on 14-12-2010

download
Located in the Haute Savoie region of Eastern France, Rotronics has been designing and manufacturing engine and chassis dynamometers since 1990. Data acquisition technology, initially developed for high level competition, has been continually evolving with respect to the needs both of the motorcycle rider and the specialist. Today, a motorcycle dynamometer is increasingly part of a professional establishment. It is a very effective diagnostic tool for the service engineer, considerably reducing the need for road testing and proven to be very commercially effecive, notably in the context of second hand vehicles. Reduced risk, less lost time, a credible and efficient workshop, an increased range of services and improved client confidence : a dynamometer stimulates your business. MOTOSCAN II is comprised of totally modular elements. This exclusive design allows great flexibility in the installation and extension of the test facility. Available as a free-standing or built-in version, with an automatic (optional) or manual front wheel support, with or without supplementary engine load, the chosen configuration can always be extended. The test bed can be transformed at will, according to the users budget or needs. Hence it is very simple to upgrade the «Lite» version to the automatic one; more frequently a permanently built- in model is converted to one that is free-standing when demanded by reoganisation of business premises or workshop (relocation, restructuring, change of activity…). MOTOSCAN II is compatible with all types of motorcycle : tourers, motocross, trials, enduro, sports… Moreover, the test procedures specific to mopeds and to scooters allow methodical adjustment of the automatic transmission thanks to characteristic operating curves.

2010 CSR Naked 125 Engine and transmission Chassis, suspension, brakes and wheels

0

Filed Under (CSR) by admin on 27-10-2010

Model: CSR Naked 125 Year: 2010 Category: Naked bike Rating: Price as new (MSRP): Euro 2199. Prices depend on country, taxes, accessories, etc. Engine and transmission Displacement: 124.80 ccm (7.62 cubic inches) Engine type: Single cylinder, four-stroke Fuel system: Carburettor Cooling system: Liquid Transmission type, final drive: Chain Chassis, suspension, brakes and wheels Frame type: Steel Front tyre dimensions: 90/90-13 Rear tyre dimensions: 130/90-15 Front brakes: Single disc Rear akes: Single disc Physical measures and capacities Dry weight: 161.0 kg (354.9 pounds) Weight incl. oil, gas, etc: 179.0 kg (394.6 pounds) Overall height: 1,085 mm (42.7 inches) Overall length: 2,110 mm (83.1 inches) Overall width: 650 mm (25.6 inches) Fuel capacity: 18.00 litres (4.76 gallons) Other specifications nStarter: Electric Color options: Black, silver Comments: Also called NKT 125. Spanish brand. Further information Parts and accessories Check out parts and accessories from our partners.nAsk questions Join the 10 CSR Naked 125 discussion group. Insurance, loans, tests Check out insurance here. Search the web for dealers, loan costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs

Incoming search terms:

Pulsar Electronic LED Turn Signal Flasher Unit Installation & Operation Instructions

0

Filed Under (Pulsar) by admin on 27-10-2010

download
1. Locate the stock flasher unit on your motorcycle and remove it. Refer to your motorcycle’s shop manual. 2. Using either the test light or voltmeter, connect or touch one lead to the chassis or ground. Turn on the ignition switch. 3. Then touch the probe of either the test-light or the other lead of the voltmeter to one of wires or contacts where the flasher was removed from. If using the test-light, the light will light up when the supply line has been located. If using the voltmeter, the meter will indicate a voltage value, if present. Important Notice: Verify which grounding type your motorcycle is using before performing one of the following procedures. This can simply be done by seeing which terminal of the battery is connected to the motorcycle’s chassis or frame. Figure 3 • Positive Earth: Connect the black wire (-V) into the contact that indicated power was present. Plug the white wire (O/P) into the other contact, which did not have any power present. Turn off the ignition switch. Cut off the connector on the red wire w/ fuse holder (+V); strip the insulation back about ¼” (6 mm) and install the ring terminal on the wire, then ground the ring terminal to a chassis bolt or screw. If ground is not available via the chassis, then connect to an earth (ground) wire from the wiring harness. • Negative Ground: Connect red wire w/ fuse holder (+V) into the contact that indicated power was present. Plug the white wire (O/P) into the other contact, which did not have any power present. Turn off the ignition switch. Cut off the connector on the black wire (-V); strip the insulation back about ¼” (6 mm) and install the ring terminal on the wire, then ground the ring terminal to a chassis bolt or screw. If ground is not available via the chassis, then connect to a ground wire from the wiring harness

Incoming search terms:

Incoming search terms: