crf150r water pump bolts torque

You search Auto repair manual PDF crf150r water pump bolts torque, if there are search results will appear below. If search results do not exist, please search by others keyword.



  crf150r water pump bolts torque Direct Download speed 5282 Kb/s

  crf150r water pump bolts torque Full Version speed 6162 Kb/s



YAMAHA Road Star Fuel Pump Relocation Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and disconnect battery. Remove fuel tank along with both left and right side battery covers, and remove air box from carburetor (all per Yamaha standard shop manual procedures). 2. Remove chrome plastic cover over fuel pump and disconnect choke cable/knob from lower pump bracket. Remove pump-to-carb fuel line from fuel pump. Disconnect fuel pumps electrical lead connector. 3. Remove two (2) hex-head pump mounting bracket bolts and remove pump assembly from motorcycle. Slide fuel pump up and off bracket mounting posts (Caution: excess fuel may drain from pump and/or fuel lines and fuel filter!). Remove heat shield. Remove remaining fuel line from pump. Pull all fuel lines from filter and remove steel springs and hose clamps from these lines (these will be reused on the kits fuel lines). With a sharp knife or box cutter, trim off the top portion of the fuel pumps rubber isolation/mount system per Photo A. Next cut pumps wiring harness approximately half way between connector and pump. Strip the insulation from the ends of these wires as well as from the supplied Baron harness extension wires. Using the supplied electrical butt connectors, crimp Baron harness extensions red wire to pumps black-w/blue-strip wire, and Baron harness extensions black wire to pumps black wire. Repeat this process on other side of wire harness extension with pumps connector. Now, referring to Photo B, you will need to cut off the square tube that runs along the side of the fuel pump with a hack saw. Cut down toward pump body in a straight cut, then cut tube off by cutting along the body. This will allow you to twist pump in the rubber mount so the curved spigot is facing up (clockwise approx 1/4 turn). 4. Remove pump-to-carb fuel line from carb and separate electrical wires from this line. Remove this fuel line from engine. Re-route choke cable to right side of engine (toward carb) and rotate it up and over rear cylinder head back toward left side of bike. Mount new Baron choke bracket to the choke cable and tighten plastic nut. New choke bracket will mount to rear fuel tank mounting location (Photo C). 5. 99~03 models – Remove electrical relay bracket (found under the right side cover) from the bike and slide each relay off of this bracket. Install fuel pump onto new Baron Fuel Pump Bracket and install bracket in the same location as the stock bracket you just removed, using stock mounting hardware. Refer to Photo F for proper installation. 6. 04~07 models Remove electrical relays from stock bracket and remove relays from rubber holder. Cut rubber holder per Photo E and replace one of the relays into the rubber and install on to new Baron bracket. The second relay will be placed to the right of the tool bag under the seat and secured with the provided two-sided tape pad. Reconnect plugs to the relays. (Photo F)

Incoming search terms:

2004 King And CM50 water pump drive belt And pulley alignment & inspection

0

Filed Under (Cobra) by admin on 10-11-2010

download
It is important to inspect three things on the water pump drive pulley and belt. Inspect 1. That the belt and pulleys are in proper alignment and that the belt is not rubbing on flywheel or edges of the pulleys 2. That the pulleys are not cracked 3. That the water pump impeller pulley fastener is tight and has adequate high strength thread lock agent applied. Below is the proper orientation of the water pump drive pulley, cover, and spacers.

How to Replacing Rear Main Seal 1

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
The next day I woke up early and drank lots of coffee before going out to the garage. I knew I had two distinct problems confronting me. First, I would have to purchase an impact tool in order to loosen the six bolts holding the clutch together. Also, I would have to purchase at least three 8mm by 50mm bolts and nuts in order to prevent the clutch from exploding when the six bolts were unscrewed. For the third time in two days, I went to Sears and asked the salesman, (who I now I knew as Art,) where I could find an impact tool. He did not know what it was I was looking for, but he asked another employee and soon I had the tool as well as a 6mm Allen socket. Unfortunately, the Allen socket only came in 3/8″ drive, and the impact tool only came in 1/2″ drive. Thinking quickly, I purchased a 1/2″ to 3/8″ adapter, as well as a 3lb. dead- blow hammer. On the way home, I stopped at a Chief Auto Parts to buy the bolts I would need. The closest size they had were 8mm by 40mm, which was nearly 10mm too short. I was unsure whether the clutch cover bolts were coarse thread or fine thread, so I bought three of each, along with corresponding nuts. Finally, around 11 o’clock in the morning, I was back at the garage ready to work. I prepared the impact tool and placed the adapter and the Allen socket on it. I began to hammer on the end of the tool, trying to loosen each of the six bolts. None of them seemed to move, even though it seemed the impact tool was turning. Finally, I put the Allen socket on the breaker bar and found that all of the bolts had actually come loose. The tension from the clutch spring made it nearly impossible to see, however. I removed three of the bolts in a triangular pattern. Into these empty holes I threaded the fine- thread 40mm bolts with nuts attached and tightened them evenly. I was now able to remove the remaining Allen bolts. By slowly turning and loosening the nuts evenly on the 40mm bolts, I relieved the pressure from the clutch spring until the cover plate was free. I removed the cover plate, the clutch, the pressure plate, and finally the clutch spring. I had already marked each of the elements with Whiteout to insure that they would fit together the same way on installation. Apparently, this is essential as the flywheel could be rendered out-of-balance if the clutch components are not installed correctly. The flywheel itself was now exposed. I could see the five bolts that attached it to the crankshaft. I now used a tool I had fabricated. Although the manual describes two possible tools that can be fabricated, I found a piece of metal that resembled the tool and decided to use it. Unfortunately it was not strong enough and broke. I turned and looked at my workbench, and noticed a bracket which I had previously fabricated for mounting a mirror on my Vespa. The piece of steel was extremely strong and was already pre-drilled with correct-sized holes. It fit perfectly, so I placed it over the exposed bolt which protruded from the case, and placed the other end on one of the 40mm bolts, which I then bolted into the flywheel itself. I used the breaker bar again and removed the five bolts. The flywheel came loose after inserting two more 40mm bolts and tugging on them evenly

Incoming search terms:

1928 AJS Installation Instruction Manual

0

Filed Under (AJS) by admin on 31-10-2010

download
Oil delivered at “6″ goes to the big end, while that delivered at “5″ goes up to the cam box. The bottom end of the plunger also has a slot, which registers alternately with inlet ” 7 ” and outlet ” 8,” and is responsible for returning the oil from the sump to the tank. It is of greater capacity than the supply pump. To dismantle the pump, proceed as follows :— 1. Remove all pipes from the pump. 2. Remove pump from engine. 3. Remove the two nuts “A” and the pin” 3 ” from the pump. 4. Gently push the plunger out of the pump body in the direction of the arrow “C” on the drawing. To re-assemble, the reverse sequence of these operations is, of course, followed. Should it be required to remove the worm ” 2,” the brass bush ” D ” which screws into the body with a R.H. thread, must be removed first. It is of the utmost importance that the nut “A” always makes an air-tight joint with the body ; and should there be no oil returning to the tank at any time, check this joint immediately. Occasionally go over all the oil pipe unions and nuts to see that everything is tight. Should one of the unions come loose, especially on the inlet side of the pump, of course, the whole system of lubrication fails. As will be seen from the illustration, the oil pump itself is very simple. There are only two moving parts, and it is most unlikely that anything in this pump will get out of order. Should the oil not be circulating and running back to the tank, be quite sure that there is plenty of oil in the tank and that the filters are clean, before dismantling the pump. Should it be necessary to take the oil pump from the engine, make certain that the short piece of square tube which drives the pump spindle from the engine is replaced. The pump delivers oil to the big end via holes drilled down the driving side of the crank­ case, then through holes in the main shaft, up web of flywheel, and through the crank pin into the big end. Oil is also taken to the cam box. A portion of the cam box projects inside the chaincase—the end of this projection is open ; the oil from the cam box falls on to the vertical chain—from there it falls through holes in the crankcase into the sump, and is returned to the oil tank. The piston and little end of connecting rod are lubricated in the ordinary way by splash from the big end, but we have found it necessary for continued high speeds on track or in road race, above (say) 60 m.p.h. average, to take an extra supply of oil direct to the cylinder walls

Tacoma Power Steering Pump Improving Power Steering Reservoir modification

0

Filed Under (Toyota Manuals) by admin on 02-10-2011

download
For my SAS I decided to add hydraulic steering assist as it comes in real handy for rock crawling. I got the Redneck Ram setup from the folks at West Texas Off-road that includes rebuilding an earlier IFS steering box along with drilling and tapping the box for the included ram. One of the down sides of adding a ram is that it slows the steering down because the stock steering pump has to supply the added volume for the hydraulic ram. Another is that it creates a fluid volume change in the system reservoir that needs to be compensated for in some way. After doing some reading on the West Texas site about how to go about modifying a Saginaw pump and reading up on earlier Toyota pump mods for steering assist setups on the Pirate board, I decided to give it whirl and see what I could do about the Tacoma pump. Chuck Gardella was kind enough to supply me with a blown pump that I could rebuild and submit to my endless fiddling and tinkering. I plan to give him my pump in return when I get this one done and installed. You need to do something to allow for more room in the reservoir for the standard hydraulic ram assist setup so I decided to tackle the reservoir first. The reason you need the extra space is because the ram is unbalanced. That is there is a rod on one side of the cylinder and not on the other side so the volume of the fluid has to change in the system to account for the volume of the rod as it travels back and forth. I calculated the volume of the rod that I have at full stroke to be about 2 oz or so. This would equate to plus or minus up to 2 oz. in the pump reservoir. Well first off, it’s no wonder why so many folks boil their steering pumps over with heavy wheeling and have so many other steering problems. The stock power steering reservoir doesn’t even rate pint sized

Incoming search terms:

1994-1998 HONDA RVF400RR Racing Kit INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
(1)Fuel High Octane white gasoline (2)Engine Oil Recommended Oil: HONDA Ultra-GP (for four-cycle Motorbike) SAE20W-50 or 10W-40
Full Capacity: 3.0Liter (5.28pt) Oil Exchange: 2.5Liter (4.4pt) Filter Exchange: 2.4Liter (4.224pt) (3)Spark Plug NGK R 847-10(11)(4)Cooling Water Highly recommend checking the water level on each ignition/riding. Ingredient: Tapped water or Drinking water I. Unscrew a radiator cap. Apply water up to limb of intake. II. Hold steering and heave the body two or three times to let air out. III.Add water if necessary. IV. Screw the cap tighten.V. Start Engine then check water level again. Add water if necessary. < Notes for racing condition> • Keep your attention when you re-check the water level since the water would spill out of intake. Also cover the body with wastes. • Drain cooling water in a catch-tank before riding. • Drain whole water in a radiator after riding. It avoids corrosion or clog of components. • It is admitted adding coolant in winter season. Handle carefully when you apply them. It makes the circuit slippery if it drops or spilled.

Incoming search terms:

2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

Incoming search terms:

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

2008 FLT Police Models Service Manual Supplement

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ITEM SERVICED 14-21 ft-lbs (19.0-28.5 Nm) Drain plug torque Engine oil and filter 4 qt. (3.8 L) Oil capacity Hand tighten 1/2-3/4 turn after gasket contact Filter 63798-99A Chrome filter part number 63731-99A Black filter part number FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity Primary chain lubricant Wet: 38 oz. (1124 ml) Dry: 45 oz. (1331 ml) 14-21 ft-lbs (19.0-28.5 Nm) Primary chaincase drain plug torque 1/2-1 turn Adjuster screw free play Clutch adjustment 72-120 in-lbs (8.1-13.6 Nm) Adjuster screw locknut torque 1/16-1/8 in. (1.6-3.2 mm) Free play at hand lever 84-108 in-lbs (9.5-12.2 Nm) Clutch inspection cover torque Dipstick at FULL with motorcycle on jiffy stand and filler plug resting on threads. Lubricant level Transmission lubricant FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity 32 oz (0.95 liters) 14-21 ft-lbs (19.0-28.5 Nm) Transmission drain plug torque 25-75 in-lbs (2.8-8.5 Nm) Transmission filler plug/dipstick torque Front: 36 psi (248 kPA) Pressure: solo rider Tire pressure and wear Rear: 36-40 psi (248-276 kPA) Replace if less than 1/32 in. (0.8 mm) of tread pattern Wear 55 in-lbs (6.2 Nm) minimum Spoke nipple torque Wheel spokes 99953-99A (12 oz.) D.O.T. 4 hydraulic brake fluid part number Brake fluid level Front: 0.20 in. (5.0 mm) Fluid level (from top of master cylinder reservoir) Rear: 0.26 in. (6.5 mm) Front: 7-10 in-lbs (0.8-1.1 Nm) Master cylinder reservoir cover screw torque Rear: 12-15 in-lbs (1.4-1.7 Nm) 0.016 in. (0.4 mm) Minimum brake pad thickness Brake pads and discs 75-102 in-lbs (8.5.-11.5 Nm) Brake caliper pad pin torque Front: 0.18 in. (4.5 mm) Minimum brake disc thickness Rear: 0.25 in. (6.3 mm) 0.008 in. (0.2 mm) Maximum brake disc lateral runout (warpage) 10 lb. (4.5 kg) Upward force applied at midpoint of bottom belt strand Drive belt deflection 3/8-7/16 in. (9.5-11.1 mm) FLHTP 1/4-5/16 in. (6.4-7.9 mm) FLHP/FLHPE 40-60 in-lbs (4.5-6.8 Nm) Air cleaner cover bracket screw torque Air cleaner 36-60 in-lbs (4.1-6.8 Nm) Air cleaner cover screw torque LOCTITE MEDIUM STRENGTH THREADLOCKER 243 (BLUE) Air cleaner cover screw Threadlocker Part No. 99642-97 (6 ml) LUBIT-8 SUPER OIL, Part No. 94968-85TV (1/4 fl. oz.) Lubricant part number Clutch cable 35-45 in-lbs (4.0-5.1 Nm) Handlebar switch housing screw torque

Incoming search terms:

Sherco Engine Engine Removal and Case Splitting Manual

0

Filed Under (Sherco) by admin on 20-04-2011

download
Engine Removal and Case Splitting Preparation 1. Wash the bike and engine thoroughly. 2. Drain transmission oil by removing drain bolt and copper washer with 5mm Allen. 3. Drain coolant by removing 3 bolts of water pump cover and lifting off engine side case.4. Remove: a. rear fender- two bolts plus one long with washer using 4mm Allen b. fuel tank hose from petcock c. fuel tank- one short bolt and washer using 4mm Allen d. chain master link and chain from front sprocket e. kick starter- one large button head bolt and washer f. rear brake- one bolt/washer using 13mm wrench g. rear brake master cylinder- 2 button head bolts h. gear shifter- one bolt i. flywheel cover – 3 bolts j. clutch slave cylinder- two button head bolts using 4mm Allen k. clutch actuating rod by pulling it out of the case l. airbox three 4mm Allen bolts and loosening Phillips head carb hose clamp m. carburetor cap/slide assembly n. carburetor by loosening Phillips head manifold hose clamp o. spark plug cap p. spark plug q. header pipe 2 bolts into cylinder head r. silencer- 3 bolts (one with washer and nut using 10mm wrench) s. cylinder head coolant hose clamp and hose t. rear shock upper bolt u. radiator plastic cover bolt, then lever up the radiator with screwdriver until the radiator “legs” pop out of frame retaining holes 5. Remove flywheel using flywheel puller tool, taking care not to lose the small Woodruff
key by placing it inside of the magnetic flywheel for safe storage. 6. Remove ignition (3 bolts) and slide rubber grommet and ignition wiring assembly out of the case and out of the way, taking special note of the ignition timing marks. 7. Remove front sprocket and 2 retaining circlips. 8. Remove clutch side case and its 10 bolts using 5mm Allen, being careful not to lose to lose the 2 aluminum alignment pins (dowel pins). Insert the dowel pins into their holes within the Right Crankcase

Incoming search terms: