crown fork lift cup holder

You search Auto repair manual PDF crown fork lift cup holder, if there are search results will appear below. If search results do not exist, please search by others keyword.



  crown fork lift cup holder Direct Download speed 5282 Kb/s

  crown fork lift cup holder Full Version speed 6162 Kb/s



HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

HARLEY DAVIDSON FX SOFTAIL FRONT LOWERING SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (T), lockwashers (S), flat washers (R) and axle cap from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) and spacer (O) from fork tube plug (B). Remove quad ring seal (D). Save bolt and spacer but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring -J03923 1 of 4 pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring (1). 11. Remove dust cover (E). 12. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 13. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 14. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). NOTE The lower stop (L) may come out with the damper tube or remain in the slider tube. Ensure that the lower stop is removed from the slider tube. 15. Remove the lower stop (L). 16. Remove damper tube (2) from fork tube. 17. Remove rebound spring (F) from damper tube. 18. Repeat Steps 1-17 for the opposite side fork assembly. Fork Assembly

HARLEY DAVIDSON FL SOFTAIL PROFILE LOW FRONT SUSPENSION KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
Fork Spring Removal 1. Elevate and support the vehicle so the front tire is off the floor and the forks are fully extended. 4 9 3 1 10 11 2 5 6 7 8 is04004 1. Slider tube cap 2. Spacer washer 3. Oil seal 4. Clamp bolt and washer 5. Fork tube plug 6. O-ring 7. Fork spring 8. Tight-wound end of spring 9. Fork slider tube 10. Fork slider 11. Drain screw and washer Figure 1. Front Fork NOTE Remove the brake caliper from the fork slider. DO NOT remove the brake line from the caliper. 2. Remove the front wheel. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. 3. Remove the front fender. See FRONT FENDER in the Service Manual. 4. See Figure 1. Remove the slider tube cap (1), spacer (2) and oil seal (3) from the top of one fork side. Save the cap and spacer. The oil seal can be discarded. 5. Loosen the clamp bolt (4) and pull the fork from the brackets. 6. Repeat Steps 4 and 5 for the other fork side. -J00280 1 of 4 Wear saf ety glasses or gog gles when ser vicing f ork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) NOTE Be careful not to damage the O-ring. 7. See Figure 1. Remove the fork tube plug (5) and O-ring (6). Pull the spring (7) out of the slider tube (9). Remove the drain screw and washer (11), and drain the fork. Reinstall the drain screw and washer, and tighten to 52-78 in-lbs (5.9-8.9 Nm). 8. Repeat Step 7 for the other fork side. NOTE The Profile® Low Front Suspension Kit requires a different amount of H-D TYPE E FORK OIL than is listed in the Service Manual. NOTE Measure the oil level from the top of the fork tube with the fork spring removed and the fork fully compressed. 9. See FRONT FORK OIL in the Service Manual, but substitute the measures below. Fill the forks with Harley- Davidson TYPE E FORK OIL: • 1986 through 1999 models: •11.7 oz (345 cc) of oil, or •5.2 inch (132 mm) from top of oil level to top of tube. • 2000 and later models: •13.4 oz (396 cc) of oil, or •4.1 inch (104 mm) from top of oil level to top of tube. Fork Spring Installation 1. Insert a new Profile Low spring (7) from the kit into each slider tube (9), with the tight-wound portion (8) toward the bottom of the fork slider. NOTE Be careful not to damage the O-ring. 2. Install the fork tube plug (5) and O-ring (6) assembly into the slider tube and tighten securely. Be sure that one flat on each fork tube plug faces toward the inside of the fork. 3. Insert both fork side assemblies up through the slider covers, the fork stem and bracket, and the upper bracket. 4. Obtain two new oil seals (3), H-D Part Number 45733-48, and the spacer washers (2) and slider tube caps (1) saved earlier. Place an oil seal, followed by a spacer washer, onto each fork tube plug. 5. Insert the threads of a slider tube cap through each washer and seal, and into the fork tube plugs. Tighten to 40-60 ft- lbs (54.2-81.3 Nm). 6. Tighten the fork stem bracket clamp bolts (4) to 30-35 ft- lbs (40.7-47.5 Nm). 7. Install the front fender. See FRONT FENDER in the Service Manual. Install the front wheel and brake caliper. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. Jiffy Stand Removal/Installation 1. Move the jiffy stand to the retracted (up) position. Wear safety glasses or goggles when removing or installing spring. Spring tension can cause spring, attached components and/or hand tools to fly out which could result in death or serious injury. (00477c) 2. See Figure 3. Unfasten the jiffy stand leg spring (A) from the vehicle. Remove the hex bolt (B), lock washer (C), flat washer (D) and leg stop (E) from the threaded end of the jiffy stand leg. Discard the jiffy stand leg, but retain all other components. 3. Clean and inspect the jiffy stand attaching parts and mounting bracket for wear or damage. If parts replacement is necessary, refer to the Jiffy Stand section of your Service Manual for replacement procedures

AJS DISMANTLING AND REBUILDING FULL-WIDTH FRONT WHEEL HUBS INSTALLATION

0

Filed Under (AJS) by admin on 31-10-2010

download
Removal of the Brake-side Bearing Cup The bearing cup (5) is located endwise by a circlip (1), and between the cup and circlip arc an oil-seal retaining washer (4), oil seal (3), and oil-seal cup washer (2) Before these parts can be removed from the hub the bearing cup must be moved inwards for a very short distance (3/16-inch) so that the circlip can be withdrawn. (n) Gently heat the hub shell. (i) Place a soft metal rod (e.g. brass) against the oil-seal cup washer (2) and apply pressure with a hand press or hammer blows. It is only necessary to move the bearing cup (5) inwards about 1/16-inch. (j) Extract the circlip by inserting a narrow pen-knife blade under one end of the circlip; lift it upwards and outwards and prise the clip out of its groove. (k) Remove the oil-seal cup washer (2), oil seal (3) and oil-seal retaining washer (4). They can be hooked out with the shank of a small and narrow screw­ driver, (l) The bearing cup can now be ejected by placing a suitable rod of soft metal (e.g. brass) in the hub tunnel from the right-hand side and pressing it — with a press or hammer blows — against the bearing cup until the cup is forced out of the bearing. This must be done with care so that the cup remains square with the housing. Reassembly To facilitate replacement of the bearing cups gently heat the hub shell. Just too hot to hold is about the right temperature. (a) Place the brake-side bearing cup squarely in the hub shell — the open end faces inwards — and press it into the hub tunnel A short length of brass rod, slightly less than the outside dia­ meter of the cup, should be interposed between the cup and ram of the press, or hammer head. Press the cup in until the outer face is approximately half-an-inch below the mouth of the hub tunnel. This will allow sufficient room to allow [he circlip to be inserted into its groove. (b) Refit in the following order: oil-seal retaining washer (4), oil seal (3), oil-seal cup washer (2). (c) The circlip can now be replaced. In the interest of reliability use a new circlip, for it is possible that the existing circlip was strained when it was re­ moved. (d) Insert into the hub tunnel from the right-hand side a brass rod of suitable length, and press the bearing cup firmly against the circlip. (e) Before inserting the spindle complete with the roller races, pack them with clean and fresh grease of a suitable grade (Mobilgrease No. 4. Castrolease heavy, Energrease C3, Esso Pressure Gun Grease. Shelf Retinax Grease CD or A). (0 Insert the spindle into the hub. (g) Place the right-hand side bearing cup in the hub tunnel; the open end faces inwards, It may be necessary to re-heat the hub to allow the cup to go into position without difficulty. (h) Press the cup into position, but do not force it fully home, leave some end play on the spindle. (i) Refit in the following order: oil-seal retaining washer (6), oil-seal (7) and oil-seal cup washer (8). (j) Screw into the hub the adjusting sleeve (9) until it comes into contact with the bearing cup (5)

Incoming search terms:

Harley Davidson 39 mm Front Spring Lowering Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 07-04-2012

download
1. Support the motorcycle so the front wheel is off the ground. Next remove the front wheel and fender. Remove the fork cap nuts and loosen the lower triple clamp pinch bolts. Remove the front brake caliper. Some models have a tapered end to the fork tube. Extra effort will be required to remove the tube from the crown. Loosen the top fork cap 1 to 2 revolutions. Use a soft wood block or similar tool (that will not mark fork cap finish) and tap down with mallet to loosen fork tube from its tapered fit in top steering crown. Make sure fork pinch bolts are loose. To completely remove fork of this style, unscrew the fork cap entirely. 2. Slide both fork assemblies out of the triple clamps. Unscrew the top fork tube plugs. Remove the plugs and fork springs. CAUTION: Fork caps are under spring pressure and could cause serious injury. Drain the fork oil by turning the fork assemblys upside-down. 3. Next, bottom the fork tube into the fork leg. DO NOT extend the tube while you remove the allen bolt on the bottom of the fork leg. Turn the assembly upside-down and shake the damper rod and rebound spring out of the fork assembly. Again, DO NOT extend the tube during this. Extending the tube could dislodge the internal bottoming cone, which fits on the end of the damping rod, making it very difficult to reinstall the damper rod without complete fork disassembly. 4. FOR 1″ REDUCTION IN FORK LENGTH: You must first measure the length of the O.E.M. rebound spring. Depending on the model of the motorcycle, the length will either be 1″ or 2″ long. A. If you currently have a 1″ rebound spring, you need to replace it with the 2″ long LA Choppers rebound spring (included in the kit), then reinstall the damper rod in the fork tube. B. If you currently have a 2″ rebound spring, you will need to add the 1″ long spacer, then reinstall the damper rod in the fork tube.

PRO-CYCLE AND PRO-CYCLE XLT 1,000-Lbs. Capacity Motorcycle Lift

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
1. Always inspect the lift for freight damage and make note of any damage on the bill of lading. 2. In case of freight damage, call the truck line immediately and report the damage as a freight claim. Final Set-Up for model Pro-Cycle This lift is more than 90% factory pre-assembled. The following steps will guide you through the final set-up. IT WOULD BE EASIER FOR TWO MEN TO COMPLETE FOLLOWING STEPS. 1. Unpack the lift from the shipping skid. With the lift table up side down, connect the air hose to the air cylinder (Part # 26). 2. After tightening the hose to the cylinder, flip the lift over with the table surface up. 5 3. Lift up the table manually to the first lock position to make sure the lift is rising freely. Lubricateing the joints again before use will ensure a better performance of the lift. 4. Connect the other end of the air hose to the foot-operated valve. Then connect the foot- operated valve to 100 PSI air supply. DO NOT USE AIR SUPPLY WITH PRESSURE MORE THAN 100 PSI. 5. Release the safety bar by pushing the handle down. Operate the foot valve by stepping on the footpad forward to raise the lift. The safety bar should engage the ladder automatically while lift is rising. Step on the footpad again to set the pad in middle position to stop the lift when it reaches the desired height. ALWAYS LOWER LIFT IN THE NEAREST LOCKED POSITION BEFORE BEGINNING WORK. NEVER USE THE LIFT UNLESS YOU ARE IN A LOCKED POSITION. The lift should never be left unattended while attached to air pressure. Disconnect the air pressure when lift is not attended by qualified persons. 6. Install the vise using bolts and nuts supplied with the lift (part # 6 to 12). See fig #1. 7. Install the approach ramp by dropping it into the holes punched on the rear edge of the table. The final Set-Up for the Pro-Cycle model is complete

Incoming search terms:

2003 – 2004 4Runner REAR SEAT CENTER ARMREST CUP HOLDER REPAIR

0

Filed Under (Toyota Manuals) by admin on 28-10-2011

download
The ends of the zipper are concealed in the cover. Pull out both ends of the zipper from the cover. B. To unlock the zipper, flip the zipper’s tab so that it points away from the direction the zipper will be opened. C. Open the zipper by pushing the tip of the tab. 3. Roll Up Cover. A. After opening the zipper, roll up the cover. B. Roll up the cover until the foam pad’s 3 holes are revealed. 4. Remove Cup Holder. A. Remove the screws from each of the 3 holes. B. Pull the cup holder out of the armrest. If the cup holder is difficult to remove, hold the armrest with the cup holder facing down and shake the armrest for cup holder remova

1500 XLT MOTORCYCLE / ATV LIFT INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
1. Load should not exceed rated capacity for this lift – 1500lbs 2. 70-160PSI shop air needed. 3. Make sure the handle is in the down position and the safety plate is set in the safety lock while the lift is in the raised position. 4. Move the lift only when it is lowered. 5. Do not ride vehicle onto lift. 6. Only trained people should operate the lift. 7. Air/Hydraulic pump should be at least 3 feet away when operating. Remain clear of the lift when raising or lowering. 8. Indoor use recommended. 9. Do not move lift while loaded. 10. Keep hands, tools and other extremities from under carriage and moving parts.. 11. Maintain a safe working environment. The work area should be clean, dry, clutter free, and sufficiently lit. 12. Wear proper ANSI-approved safety attire. Do not wear loose fitting clothing while operating lift, long hair and sleeves should be secured. 13. Keep children and bystanders away from work area. Do not let children operate or play on lift. 14. Do not use if under the influence of drugs or alcohol. Operator must be alert at all times when using heavy lift equipment. 15. Never operate the lift with someone on it. 16. Do not adjust safety valve. 17. Use this lift only for the work it is intended. Do not use this product for an application for which it was not designed. Misuse can lead to personal injury and/or property damage. 18. Industrial applications must follow OSHA requirements. 19. Do not use for aircraft purposes. 20. Have your lift serviced by a qualified repair person using only identical Titan Lifts® replacement parts and attachments. This will ensure that the safety of the lift is maintained.

SUSPENSION SERVICE TOOLS/ FORK DAMPER ROD BLEED TOOL

0

Filed Under (Tips and Review) by admin on 30-11-2010

download
33 SHOP EQUIPMENT & TOOLS SUSPENSION SERVICE TOOLS K&L FORK TUBE U-BLOCKS Precision machined from billet aluminum, these quality three piece sets are a handy, accurate and safe way to straighten and check fork tubes. 35-9411 36mm (for 33 thru 36mm tubes) 35-9412 40mm (for 37 thru 40mm tubes) 35-9413 43mm (for 41 thru 43mm tubes) 35-9414 46mm (for 44 thru 46mm tubes) 35-1964 35-8579 35-7995 DAMPER ROD HOLDERS Holds damper rod when disassembling forks. 35-8578 Yamaha front forks, 43mm Kayaba YZ125/250 (1988) YZ490 (88-90) 35-8579 Yamaha YZ125/250 with UD(upside down) forks FORK DAMPER ROD TOOLS Sold each. 35-7995 Combination Fork Damper Tool Designed to hold the damper rod during assembly & disassembly of Honda XR400′s or Suzuki DR-Z400S. One end features spanner type prongs for the XR400 and the other a 27mm hex for Suzuki. 35-1964 Combination Damper Rod Fork Tool Designed for assembly and disassembly of most inverted Kayaba and Showa 41mm, 43mm, 46, and 47mm forks. Use one end for Kayaba forks and the other for Showa forks. (not required for 91-92 Honda CR models) ROD HOLDER Double sided damper rod holder. Works on Kayaba U.D (upside down) 41mm forks. 35-8580 Yamaha YZ125/250Amodels (89-90) FRONT FORK CAP SOCKET Designed to remove and install Yamaha front fork caps with female hex head. Sold each. 35-8571 14mm female socket 35-8573 19mm female socket FORK DAMPER ROD HOLDERS Holds damper rod when disassembling and assembling front forks. 35-8576 Use for Yamaha 43mm Kayaba forks, 30mm hex YZ125 (84-87), YZ250 (81-87) IT250 (1983) YZ490 (82-87) 35-8577 Use for Yamaha 38mm Kayaba forks, 24mm hex YZ125 (81-83), IT175 (82-83), IT250 (81-82) YZ250 (77-80), YZ400 (77-79), IT465 (81-82) FORK CAP WRENCH Designed to remove the front fork caps on late model Honda CR’s and Suzuki RM’s. Can also be used for adjusting compression. One end of wrench is 49mm, the other is 50mm. Sold each. 35-7803 Fork Cap Wrench 35-8576 35-8577 35-8571 35-8573 6 Point Hex 35-8578

Incoming search terms:

Incoming search terms: