darn fine trike parts manual

You search Auto repair manual PDF darn fine trike parts manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  darn fine trike parts manual Direct Download speed 5282 Kb/s

  darn fine trike parts manual Full Version speed 6162 Kb/s



Honda VTX 1300 Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 27-10-2010

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) · Passenger Seat (to be reinstalled without modification) NOTE: OEM front and rear seat mounting bolts and brackets to be retained and reused. · Left and right passenger foot rests. (to be re-installed later). · Mufflers (to be re-installed and relocated with minor modification) · Rear Fender (complete w/ sub frame and all attaching parts) · Swing Arm, Drive Shaft and Rear Wheel (complete w/ all attaching parts) · Rear brake Line to hard line in front of the Swing Arm. Core Return There are NO core return parts for this model. Honda VTX 1300 TRIKE CONVERSION CHAMPION TRIKES Installation Manual Page 7 of 16 Revision 2 3 Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Cut and remove passenger foot rest mount from OEM frame on both sides (left hand side picture shown) . Figure 1 b. Clean cut frame and paint black. c. Remove and secure Charcoal Canister. d. Cut and remove charcoal canister frame bracket. Figure 2 e. Clean cut frame and paint black

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

Yamaha Road Star Trike Conversion Installation Manual

0

Filed Under (Yamaha) by admin on 17-02-2011

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster

Yamaha Road Star Motorcycles Trike Conversion Removal And Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model. nstallation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster plates. Figure 3 Qty per Assm Spec Description 2 M10 x 1.25 x 70 Hex Head Bolt 2 M10 x 1.25 Hex Nut b. Install adjuster plates to rear drive pinch blocks. Hardware installs from inboard to outboard side. Snug, but do not tighten hardware at this time. Figure 4

Incoming search terms:

Harley-Davidson FLH Series 2008 and Down, Independent Suspension Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 07-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. Make sure the engine is turned off and battery disconnected before you begin work.  Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine.  Burns from hot parts: Let the engine and exhaust system cool before working on those areas.  Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. c. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. d. Use only nonflammable solvent, not gasoline, to clean parts e. Never drain or store gasoline in an open container. f. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.5 Specifications Overall Length: 103″ Overall Width: 57.25″ Wheel Base: 53″ Load Capacity: 600 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4 on 4.5 Tire Pressure: 24-26 PSI Suspension: Double A-arm Independent Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 5.75 cubic feet. Two full-face helmets and additional storage.
Harley-Davidson® FLH 2008 & Down Independent Suspension CHAMPION TRIKES Installation Guide Page 6 of 20 Revision 4 2 Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted.  Seat – to be re-installed; without modification.  Left and right side covers – to be re-installed after modification.  Tour Box – to be re-installed (if so equipped).  Left and right saddle bags (if so equipped).  Left and right rear crash bars, saddlebag rails (if so equipped).  Tour Box mounting frame (if so equipped).  Left and right passenger foot rests – to be re-installed without modification.  Left and right mufflers  Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake Caliper is removed.  Remove Rear Caliper (disconnect brake line at Caliper). NOTE: Cap line to prevent introduction of dust / debris into line. Remove Caliper

HARLEY DAVIDSON 80-SPOKE REAR WHEEL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
Additional Parts Required This kit includes the custom wheel only. Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer: •Wheel Bearing Remover and Installer (HD-44060) •Wheel Installation Kit (See Service Parts Tables for part number) The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See the Service Parts section for kit contents. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. NOTE Remove the rear brake caliper before removing the wheel. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. Install the tube and tire on wheel. Refer to REAR WHEEL in the Service manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. 4. Install rear wheel (1), stock axle and stock axle nut. Refer to REAR WHEEL in Service Manual

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

Honda VTX 1800 Motorcycles ALL Models (Excluding C Model) Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
Specifications Overall width 55.5 in. Overall length 108.06 in. Overall length w/ EZ-Steer 111.75 in. Wheelbase 72.44 in. Wheelbase w/ EZ-Steer 76.125 in. Load capacity 640 lbs. Brakes High-performance rear disc Tires 205/70R-15 Turning Radius 12.3 ft. Wheels Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20-25 psi · Suspension: “Zero-Flex” swing arm and two new (replacement) Progressive coil-over shocks. · Rear Differential: Champion Left Hand Drive Light Weight Rear Differential Assembly. · Brakes: Original front plus 2 high performance disc brakes at rear. · Storage Capacity: 6.75 cubic feet – 3 full-face helmets and additional over wheel storage. 2 Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) . · Passenger Seat and mounts (to be reinstalled without modification) . NOTE: OEM front and rear seat mounting bolts to be retained and reused. · Left and right passenger foot rests and mounts (to be reinstalled with modification) . · Mufflers (to be re-installed and relocated with minor modification) . · Rear Fender (complete w/ sub frame and all attaching parts) . · Swing Arm, Drive Shaft and Rear Wheel (complete w/ brake line and all attaching parts) . Core Return There are NO core return parts for this model. Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Use 17/64″ drill and drill through frame from inside out using passenger footrest mount holes as guide. b. Enlarge the passenger footrest mounting holes on the left and right side of the frame to 27/64″. c. Enlarge the holes in the left and right passenger footrest mounting plates to 27/64″. d. Clean area of all debris. 3.2 Relocate Regulator a. Install supplied “Z” bracket to the regulator as shown using the supplied hardware. b. Attach regulator to frame using the supplied hardware. c. Tie hoses down to avoid contact with the swing arm. Qty Description 1 ¼-20×2 hex head bolt 1 ¼-20×1-1/4 hex head bolt 6 ¼-20 Nyloc nut 10 1/4- SAE flat washer 4 as spacers 3.3 Hose Stay a. For models that have a recover tank below the swing-arm, a holder has been included keep the hose connected to the water pump away from the champion swing-arm. b. Remove the hose from the top of the recovery tank. c. Push the water pump hose forward against transmission. d. Secure hose with supplied stay as shown using existing bolt. Ensure that hose is not being crushed. Bend stay if necessary. e. Reconnect hose to recovery tank

Honda VTX 1300 Motorcycles All Models Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) · Passenger Seat (to be reinstalled without modification) NOTE: OEM front and rear seat mounting bolts and brackets to be retained and reused. · Left and right passenger foot rests. (to be re-installed later). · Mufflers (to be re-installed and relocated with minor modification) · Rear Fender (complete w/ sub frame and all attaching parts) · Swing Arm, Drive Shaft and Rear Wheel (complete w/ all attaching parts) · Rear brake Line to hard line in front of the Swing Arm. Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Cut and remove passenger foot rest mount from OEM frame on both sides (left hand side picture shown) . Figure 1 b. Clean cut frame and paint black. c. Remove and secure Charcoal Canister. d. Cut and remove charcoal canister frame bracket. Figure 2 e. Clean cut frame and paint black f. Install supplied Canister/Regulator bracket with supplied hardware. Figure 3. Make sure the hoses/electrical wires are routed underneath the bracket as shown. Figure 4 Qty Description 2 3/8-24×1-3/4 hex head bolt 4 3/8 SAE flat washers 2 3/8-24 Nyloc nuts g. Install Canister and Regulator with supplied hardware. Figure 4 Qty Description 4 ¼-20×1-1/4 hex head bolt 8 ¼ SAE flat washers 4 1/4-20 Nyloc nuts

Honda CBR 400RR Service and Repair Manual

0

Filed Under (Honda) by admin on 16-12-2011

download
Once you have found al1 the identification nurnbers, record thern for reference when nbuying parts. Since the rnanufacturers change specifications, parts and vendors (cornpanies that rnanufacture various cornponents on the
rnachine), providing the ID nurnbers is the only av to be reasonablv sure that vou are buvina Model, c ~ d e and
production year CBR400RR-J (1988) CBR400RR-K (1 989) CBR400RR-L (t990 and 91) CBR400RR-N (1992 and 93) CBR400RR-R (1 994-on) , the correct parts. Whenever possible, take the worn pari to the dealer so direct cornparison with the new cornponent can be rnade. Along the trail frorn the rnanufacturer to the parts shelf, there are nurnerous places that the part can end up with the wrong nurnber or be listed incorrectly. The two places to purchase new parts for
your rnotorcycle – the accessory shop and the rnotorcycle dealer – differ in the type of parts they carry. While dealers can obtain virtually every part for your rnotorcycle, the accessory shop is usually lirnited to norrnal high wear iterns such as shock absorbers, tune-up parts, various engine gaskets, cables, chains, brake parts, etc. Rarely will an accessory outlet have rnajor suspension cornponents, cylinders, transrnission gears, or cases. Used parts can be obtained for roughly half the price of new ones, but you can’t always be sure of what you’re getting. Once again, take your worn part to the breaker for direct cornparison. Whetherhu~ng new, used or rebuilt parts, the best course is to dea1 directly with sorneone who specialises in parts for your particular rnake. Frame nwnber NC23-1020001 t0 1036454 NC23 t090001 t0 10981 16 NC29-1000001 to 101 0598 NC29-1050001 on NC29-l t00001 on Unofficial (grey) imports
All CBR400RR rnodels in the LIK are unofficial (grey) irnports frorn Japan. The rnajority are second-hand rnachines and are allocated age-related licence plates for UK use (the licence plate letter reflects the production year in Japan), although new CBRs are allocated current year UK registration letter plates. Cornrnon changes rnade prior to sale in the UK are the disabling of the rev-lirniter device (or more correctly ‘speed-lirniter’ device), which is fitted to cornply with Japanese rnarket regulations. The device is located inthe speedorneter head and is linked to th

Incoming search terms: