de plastics industries contactgmbh email mail

You search Auto repair manual PDF de plastics industries contactgmbh email mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





Honda CBR 600 F4i 2004 – 2005 Bestem USA Fiberglass F13 Installation Guide

0

Filed Under (Honda) by admin on 20-11-2011

download
We highly recommend having a professional install this undertail. A dremel tool or nsimilar is what we found the best to cut plastics. Place bike on a rear wheel center stand. Remove passenger seat and hardware which secure stock undertail section Unplug the harness that connects tail light and remove the stock undertail. Position Bestem undertail close to the bike and determine the amount of plastic needs to be cut out. Use a dremel tool to carefully trim off plastics (glove boxes etc). This is the most time consuming part of the installation but your patience will be paid off. 5) Once the new undertail is slide in, determine holes need to be drilled (only on
certain models). Reuse the hardware for the stock undertail to secure the new undertail. 6) The wiring color codes from two round tail lights are Black Wire – Ground, connects to Ground wire. Red Wire – Brake Light, connects to brake light. Blue Wire – Running Light, connect directly to the running light. Orange Wire – Turn Signal, connect them to your L/R turn signal wires We highly suggest you solder the connections and use heat shrink wrap to seal the connections. Test your lights before going out for a ride, also make sure your new undertail is securely installed on the bike. Now it’s time to go out for a spin!

Harley Davidson BoonDocker Nitrous System Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 2 of 10 This manifold is also designed to vary the float bowl pressure in relation to nitrous pressure, thus keeping the nitrous and fuel delivery in sync. Fluctuations in bottle temperature greatly affect nitrous pressure, which affects nitrous delivery. By automatically adjusting the fuel delivery as nitrous pressure varies, this manifold makes nitrous safe, reliable, and easy to use. Be sure to understand and follow the tuning instructions at the end of these instructions. Proper tuning is an important part of any performance-enhancing product. Part I – Bottle Installation A. Bottle Valve Fittings Insert the 4AN x 1/8″ NPT fitting and the 1/8″ NPT Plug into the bottle valve (these are attached to the lid of the box for the bottle) . Use Teflon tape to seal the threads – be sure not to get tape inside the threads! B. Bottle Mounting Position With nitrous in the bottle, both nitrous liquid and nitrous gas are present under high pressure (760 psi at 70 deg F) . Due to gravity and acceleration forces, the liquid portion of the nitrous will be at the bottom and rearward parts of the bottle. For this nitrous system to work properly, it is important that nitrous liquid be drawn from the bottle. Nitrous vapor will cause a significant decrease in performance. For best results, the bottle should be mounted so the valve is pointed down and towards the back of the vehicle as shown below. ************** *************** ******** ********* *************** (can be installed on top or bottom of air boot) ********** ********* push-button switch (mounts on handlebar) +12 V *********** ************ **** ****** *! “**#$******%* *! “**#$*#*%* 20 deg to 90 Front of motorcycle Rear of motorcycle BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 3 of 10 Bottle mounted inside airbox: For some applications, a small bottle can be mounted inside the airbox as shown. Note: because of the restricted space, it was necessary to mount this bottle at a non-optimal angle (the valve is pointed towards the front instead of the rear)

Incoming search terms:

DMCA

0

Filed Under () by admin on 23-05-2017

Digital Millennium Copyright Act (DMCA) Notice

We are in compliance with 17 U.S.C. $ 512 and the Digital Millennium Copyright Act (“DMCA”). It is our policy to respond to any infringement notices and take appropriate actions under the Digital Millennium Copyright Act C’DMCA”) and other applicable intellectual property laws.

If your copyrighted material has been posted on our website or if hyperlinks to your copyrighted material are returned through our search engine and you want this material removed, you must provide a written communication that details the information listed in the following section. Please be aware that you will be liable for damages (including costs and attorneys’ fees) if you misrepresent information listed on our site that is infringing on your copyrights. We suggest that you first contact an attorney for legal assistance on this matter.

The following elements must be included in your copyright infringement claim:

1. Provide evidence of the authorized person to act on behalf of the owner of an exclusive right that is allegedly infringed.
2. Provide sufficient contact information so that we may contact you. You must also include a valid email address.
3. You must identify in sufficient detail the copyrighted work claimed to have been infringed and including at least one search term under which the material appears in our search results.
4. A statement that the complaining party has a good faith belief that use of the material in the manner complained of is not authorized by the copyright owner, its agent, or the law.
5. A statement that the information in the notification is accurate, and under penalty of perjury, that the complaining party is authorized to act on behalf of the owner of an exclusive right that is allegedly infringed.
6. Must be signed by the authorized person to act on behalf of the owner of an exclusive right that is allegedly being infringed.

Send the infringement notice via contact form with “DMCA Complaint” as your subject line otherwise we won’t be able to process your complaint.

Please allow up to a week for an email response. Note that emailing your complaint to other parties such as our Internet Service Provider will not expedite your request and may result in a delayed response due to the complaint not being filed properly.

Incoming search terms:

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

Kawasaki KLX450R Dual Sport Kit Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the seat, fuel tank, and side panels. 2. Unplug and remove the stock headlight. 3. Taillight Installation: The Baja Designs taillight will run in conjunction with the stock taillight for this installation. Start by removing the first wire guide that the stock taillight wires pass through near the end of the fender. Once removed, trim off the remaining molded mounting boss as shown in Photo 1. Drill three ¼” holes in the fender and use the provided countersunk mounting hardware to attach the Baja Designs taillight as shown in Photo 2. The rear edge of the LED cluster should line up with the rear edge of the fender. Route the wires forward between the plastics to the left of the front mounting bolt. We’ll attach them in a later step. Photo 1 Molded mounting boss removed Stock taillight Photo 2
4. Turn Signal Installation: Drill a 7/16″ hole in each side of the fender plastic in the locations shown in Photo 3. Install the rear turn signals and route the wires forward as shown in Photo 4. Photo 3 Photo 4 Zip-tie BD taillight wires to fender here Route left signal wires through fender with stock taillight wires 5. Brakelight Switch: The KLX uses a hydraulic operated switch to activate the brakelight. Installation of this switch requires bleeding the rear brake system. If you do not feel competent performing this task please refer it to a qualified mechanic. An improperly bled brake can lead to rear brake failure. Caliper Guard Modification: The hydraulic brakeswitch replaces the banjo-bolt that attaches the rear brake hose to the caliper. Because of its larger size, the plastic caliper guard must be relieved slightly to provide clearance. Remove the caliper guard and modify as shown in Photo 5.

YAMAHA XS650 Garage Carburetor Guide Introduction

0

Filed Under (Yamaha) by admin on 31-10-2010

download
Loop the hose around the bottom of the yardstick and secure it with wire or twist ties so that it runs straight up both sides; avoid pinching. Trim the ends to the same length, and cut an 8″ piece from each end. Suck ATF into the line so that it fills the tubing about 8″ high on each side. Splice the end pieces back on with the pilot jets. Remote Fuel Bottle. On OEM carbs with a central synchronizing screw,adjustment (see Section II.) is easiest with the tank removed. Make a remote tank from a 1 qt. plastic bottle. Install a 1/4″ hose barb in the bottom of the bottle and a lawn mower fuel valve in the line (an in-line filter is also a good idea). Attach a wire to the top of the bottle and hang it where you need it. Safety note: many plastics will break down with exposure to fuel. Be sure your material is fuel resistant, and empty the container immediately after use. This item is not strictly necessary. 5twins recommends rough adjustment with the tank removed, using fuel remaining in the float bowls, followed by fine adjustment with the tank in place, reaching in with a long screwdriver. You can also set the tank on a work bench or other elevated surface and run extensions to the carburetor lines. Compressor If you intend to do much mechanical work at all, an air compressor with sufficient capacity to power an impact wrench will pay for itself quickly. For carb cleaning, attach an air gun with a rubber tip.

2001 HONDA GL1800/ A Radio Muting Improvement

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Place the faulty radio in the same box in which the exchange radio was sent. THE FAULTY RADIO (CORE) MUST BE RETURNED IN THE SAME BOX IN WHICH THE EXCHANGE RADIO WAS SHIPPED. These boxes are identified by the label shown below which is printed on the inside of the lid. 2. Fill out the pre-printed FedEx airbill that came in the box with the exchange radio. The airbill should have the following address preprinted on it: AHM Remanufactured Parts c/o NK Parts Industries Inc./West 2640 Campbell Rd. Sidney, OH 45365-8836 • Do not use an ordinary FedEx airbill. The pre- addressed airbill has a special account number on it for the exchange program. If you need more airbills, call the Radio Order Desk toll free, not your assigned Parts Center . • Write your dealer number and the warranty claim number in the area shown in the sample airbill ffix the FedEx Airbill to the outside of the box. Radios sent in a box not bearing the correct FedEx airbill will not be accepted for reimbursement under this program. 4. Enclose a copy of the HONDANET for Windows warranty claim in the box. If the claim form is incomplete or not in the box, the faulty radio will be returned to your dealership. 5. Ship the faulty radio to the preprinted address on the airbill. NOTE: Do not ship the faulty radio to the manufacturer or the Warranty Parts Inspection (WPI) Center. 6. For your records, on the repair order include the following: • warranty claim number • original part number • FedEx airbill number When the faulty radio is received, a core credit will be posted to your dealership’s Balance Forward Account. The credit can be identified by the claim number + “CORE” (e.g., 12345/CORE). REMEMBER: A copy of the HONDANET for Windows warranty claim must be included in the box. RETURNING THE FAULTY RADIO The faulty radio must be returned within 20 days of

Incoming search terms:

Kawasaki Mule 2003 and newer Plow Mounting Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 01-05-2012

download
Prior to installing the plow mount the vehicle must be prepped. If not already done so, install a WARN winch kit. Roller fairlead that comes with the winch kit does not need to be installed. This kit comes with a special fairlead to be used with plow. 2. Begin by locating and removing the two rear bumper mounting bolts. See Figure 1 and 2. Figure 1 Location of bumper bolts to remove Figure 2 Remove bumper bolts, both sides Location of bolt to remove WARN® INDUSTRIES PAGE 5 72171 Rev A0 4. Loosely install the mounting brackets to the vehicle using the 7/16″ hardware in the rear replacing the bumper mounting hardware removed in step 2. Do not tighten. See Figure 4 and 5

2007 Toyota Camry LE/ SE/ XLE Exhaust System Installation

0

Filed Under (Toyota Manuals) by admin on 30-05-2011

Download
By installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms stated below. It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your Borla Performance Exhaust System Borla Performance Industries assumes no responsibility for damages occurring from misuse, abuse, improper installation, improper operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s products and/or systems. Included with your Borla Performance Exhaust System is a warranty card. Please read it carefully before you begin any work on your vehicle. If you should have any questions regarding our warranty policy, nstallation, or any other matter pertaining to your new Borla Performance Exhaust System, please give us a call at the number provided on the warranty card

Kawasaki Prairie 360,650,700 ATV PLOW Plow Mounting Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Mount Installation Note: There are different hole locations on the plow mount depending on the bike model. For Prairie 360 use the middle hole locations (B), for Prairie 650 and Twin Peaks 700 use hole locations (A) on mounting plate, as shown in Figure 1. Figure 1 Hole Locations WARN INDUSTRIES PAGE 3 67954 Rev A3 To install the plow mount to the underside of the vehicle install the front two U-bolts PN 60869, and loosely tighten the 5/16″ nuts. Pull the plow mount back in the furthest position and then fully tighten, as shown in Figure 2. For the Kawasaki Prairie 360 use the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (B) . For Kawasaki Prairie 650 and Suzuki Twin Peaks 700 drill a 3/8″ hole through the aluminum skid plate, using the plow mount as a template, as shown in Figure 3. Repeat the same process on the other side. After both holes are drilled attach the mounting plate with the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (A) . Tighten all fasteners securely. Torque 5/16″ Bolts: 20ft. lb.

Incoming search terms: