diagram of carburetor choke open and closed

You search Auto repair manual PDF diagram of carburetor choke open and closed, if there are search results will appear below. If search results do not exist, please search by others keyword.



  diagram of carburetor choke open and closed Direct Download speed 5282 Kb/s

  diagram of carburetor choke open and closed Full Version speed 6162 Kb/s



HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

HSR Carburetor Total Kits Installation And Tuning Manual

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
1. Disconnect the battery ground wire from the battery. 2. Turn the fuel petcock to the “OFF” position. 3. Elevate the rear of the fuel tank for better access to the carburetor area. 4. Remove the coil, horn or other devices on the left hand side of the engine to allow free access to the intake manifold bolts. 5. Remove the complete air cleaner assembly, including the backing plate. 6. Disconnect any vacuum hoses and the fuel hose from the stock carburetor. 7. Disconnect the choke cable from the frame. 8. Remove the stock carburetor. 9. Evo: remove the stock manifold. 10. Twin Cam: unplug MAP sensor, remove manifold and then remove the MAP sensor from the manifold. Installation: Intake Manifold: Twin Cam only: Install MAP sensor in Mikuni manifold. 1. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 2. Attach the rubber flange to the Mikuni manifold with the 5/16″x3/4″ bolts and washers. To ease installation, use liqiud detergent to lubricate the manifold seals. Choke: Evo: We recommend that you use the Mikuni choke cable that is furnished with the carburetor. However, you can use the stock Harley cable (’90-’99 models only) if you follow the Twin Cam choke cable instructions. Twin Cam: 1. Remove the Harley choke cable from the stock carb. 2. Remove the Harley spring and plunger from the Harley choke cable. 3. Remove the Mikuni spring and plunger from the Mikuni carburetor. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut. 6. Install the new assembly into the Mikuni. Be careful to only gently tighten the plastic nut.

HOVELHEAD & IRONHEADXL 42mm Mikuni Carburetor And Manifold Kit INSTALLATION Instructions

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
THROTTLE CABLE ADJUSTMENT A) Rotate the throttle grip to the full open position, look into the throttle bore and see if the throttle valve (slide) opens completely. If the throttle valve does not open completely unscrew the adjuster on the opening cable until it does. This adjustment should be made carefully to assure maximum carburetor performance. After adjustment tighten the adjuster jam nut. B) After adjusting the open cable, adjust throttle freeplay with the closing (idle) cable to approximately 1/8″ an indicated in the following illustration. note It is very important to adjust the cables in the preceding described manner to ensure that the idle cable operates correctly for safety. It must close the throttle completely 2 PLEASE NOTE USE CAUTION PLEASE NOTE SAFETY WARNING pull open cable pull close cable SHOVELHEAD/IRONHEAD XL Installation Instructions Check and make sure that the throttle cables are routed properly by rechecking the throttle play as the handlebars are turned from side-to-side; the amount play should remain consistent. C) After the throttle cables have been adjusted, make sure that all the lock nuts are securely tightened. 5. AIR CLEANER A) The air filter bracket is attached to the crankcase with 1 long bolt, and a bracket-spacer. Removed the crankcase nut located between the tappet blocks & replace it with the enclosed bracket spacer; tighten the spacer securely. B) Remove the stud protectors from the K&N filter and place the two backing plates on the studs. Now slip the the filter onto the carburetor. C) Attach the 2 long brackets to the air filter studs with the enclosed nuts & flat washers, and to the bracket spacer with the enclosed bolt using the lock washers, and flat washers. When the carburetor and air cleaner are properly aligned, securely tighten all of the mounting hardware including the intake manifold clamps. In some cases it may be necessary to bend the brackets slightly to arrive at the correct fit. D) Use the enclosed hose clamps to secure the fuel hose to the petcock, and the HSR carburetor. The screw clamp goes on the petcock end and the spring clamp attaches to the carburetor end. E) Attach the chrome air filter cover with the enclosed socket head screw. 7. CHOKE CABLE INSTALLATION A) Attach the Mikuni choke cable bracket to the original choke cable bracket on the air cleaner stud with the enclose hardware as illustrated

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

2008 KTM 50 SX JUNIOR 50 SX OWNER'S MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Choke Dell’Orto carburetor PHVA 14 DS (50SXJunior) Choke lever [1] is mounted to the right side of the carburetor. If you move the choke lever up to the stop, a hole is opened in the carburetor through which the engine can draw in additional fuel. This results in a “rich” fuel-air mixture required for a cold start. Moving the choke lever back closes the hole in the carburetor again. Choke Dell’Orto carburetor PHBG 19 BS (50 SX) Choke control knob [2] is mounted to the left side of the carburetor. If you pull the choke control knob up to the stop and turn it 90º, a hole is opened in the carburetor through which the engine can draw additional fuel. This results in a “rich” fuel-air mixture required for a cold start. Turning back the choke control knob returns the knob to the starting position and closes the hole in the carburetor again. Kickstarter The kickstarter is mounted on the right side of the engine. Its upper part can be swivelled. Foot brake lever The foot brake lever is located in front of the right footrest. The basic position can be adjusted to the seating position (see maintenance work). Side stand (50 SXJunior) Use your foot to swing the side stand forwards to the stop. Make sure it rests securely on solid ground.

KTM 60 SX / 65 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 12-11-2010

download
Carburetor adjustment Basic information about the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95). Mixing ratio 2-stroke motor oil : super fuel 1:40 . Basic information of changing the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB: high altitude or high temperatures  choose leaner carburetor adjustment low altitude or low temperatures  choose richer carburetor adjustment * WARNING * -ONLYUSE PREMIUM – GRADE GASOLINE ROZ 95 MIXED WITH HIGH – GRADE TWO – STROKE ENGINE OIL . OTHER TYPES OF GASOLINE CAN CAUSE ENGINE FAILURE , AND USE OF SAME WILL VOID YOUR WARRANTY . -ONLYUSE HIGH – GRADE 2- STROKE ENGINE OIL OF KNOWN BRANDS ( I . E .SHELL ADVANCE RACING X). -NOTENOUGH OIL OR LOW – GRADE OILCAN CAUSE EROSION OF THE PISTON . USING TOO MUCH OIL , THE ENGINE CAN START SMOKING AND FOUL THE SPARKPLUG . -INTHE CASE OFA LEANER ADJUSTMENT OF THE CARBURETOR PROCEED CAUTIOUSLY . ALWAYSREDUCETHEJETSIZEINSTEPSOFONENUMBERTOAVOID OVERHEATING AND PISTON SEIZURE . NOTE: If despite a changed adjustment the engine does not run properly, look for mechanical faults and check the ignition system. Basic information on carburetor wear As a result of engine vibrations, throttle valve, jet needle, and needle jet are subjected to increased wear. This wear may cause carburetor malfunction (e.g., overly rich mixture). Therefore, these parts should be replaced after 1000 hours of using. Idling range – A Operation with closed throttle valve. This range is influenced by the idle adjusting screw 1 . Only make adjustments when the engine is hot. The idling speed can be changed by turning the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Opening up – B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range – C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

HONDA CRF250X OWNER'S MANUAL

0

Filed Under (Honda) by admin on 01-12-2010

download
Always follow the proper starting procedure described below. Your motorcycle can be kickstarted wirh the transmission in gear by pulling in the clutch lever before operating the kickstarter. Preparation Make sure that the transmission is in neutral. Turn the fuel valve ON. Fuel Valve Starting Procedure Always follow the proper starting procedure described as follow. 4. Warm up the engine; don’t operate the throttle. 5. About 15 seconds after the engine startes, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. High Air Temperature 35°C (95°F) or above 1. Do not use the choke. 2. Keep the throttle fully closed. 3. Start the engine following step 3 under Normal Air Temperature. Low Air Temperature 10°C (50°) or below 1. Follow steps 1-4 under Normal Air Temperature. 2. Continue warming up the engine until it runs smoothly and responds to the throttle when the choke knob is pushed back all the way to fully OFF. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. Hot Engine Starting 1. Pull the hot start lever (3) and start the engine following step 3 under Normal Air Temperature. 2. As soon as the engine starts, release the hot start lever. NOTICE NOTICE Basic Operating Instructions 15 (1) fuel valve The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor. ON -Turning the fuel valve ON before attempting to start the engine allows fuel to flow from the fuel tank to the carburetor. OFF -Turning the fuel valve OFF after stopping the engine prevents the flow of fuel from the fuel tank to the carburetor. RES -Turning the fuel valve to RES allows fuel to flow from the reserve fuel supply to the carburetor. (1) fuel valve (2) choke knob Check the engine oil, transmission oil and coolant levels before starting the engine (pages 44,47,48). To restart a warm engine, follow the procedure for ”High Air Temperature. ” Normal Air Temperature 10°C-35°C (50°F-95°F) 1. Pull the choke knob (2) up all the way to fully ON, if the engine is cold. 2. Keep the throttle fully closed. 3. Pull the clutch lever all the way in, and press the starter button with the throttle completely closed. Or operate the kickstarter to start the engine. Starting from the top of the stroke, kick through to the bottom with a rapid, continuous motion. Do not operate the throttle. Allowing the kickstarter to snap back freely against the pedal stop can damage the engine case.

2005 Honda CRF450X OWNER'S MANUAL AND COMPETITION HANDBOOK

0

Filed Under (Honda) by admin on 04-12-2010

download
Starting & Stopping the Engine Always follow the proper starting procedure described below. Your CRF can be started with the transmission in gear by pulling in the clutch lever before operating the kickstarter or start button. Preparation Make sure that the transmission is in neutral. Turn the fuel valve ON. Fuel Valve Starting Procedure Always follow the proper starting procedure described as follow. 5. Warm up the engine; don’t operate the throttle. 6. About 15 seconds after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. HighAirTemperature 35°C (95°F) or above 1. Turn the fuel valve (1) ON. 2. Do not use the choke. 3. Keep the throttle fully closed. 4. Start the engine following step 4 under “Normal Air Temperature.” LowAirTemperature 10°C (50°) or below 1. If the temperature is below 32°F (0°C), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 2. Follow steps 1-5 under “Normal Air Temperature.” 3. Continue warming up the engine until it runs smoothly and responds to the throttle when the choke knob is pushed back all the way to fully OFF. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. (cont’d) NOTICE NOTICE Basic Operating Instructions 15 (1) fuel valve The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor. ON -Turning the fuel valve ON before attempting to start the engine allows fuel to flow from the fuel tank to the carburetor. OFF -Turning the fuel valve OFF prevents the flow of fuel from the fuel tank to the carburetor. RES -Turning the fuel valve to RES allows fuel to flow from the reserve fuel supply to the carburetor. (1) fuel valve (2) choke knob Check the engine oil, transmission oil and coolant levels before starting the engine (pages 44,47,48). To restart a warm engine, follow the procedure for”High Air Temperature.” NormalAirTemperature 10°C-35°C (50°F-95°F) 1. Turn the fuel valve (1) ON. 2. Pull the choke knob (2) fully ON, if the engine is cold. 3. Keep the throttle fully closed. 4. Pull the clutch lever all the way in, and depress the start button. Or operate the kickstarter to start the engine. Starting from the top of the stroke, kick through to the bottom with a rapid, continuous motion. Do not operate the throttle. Allowing the kickstarter to snap back freely against the pedal stop can damage the engine

HARLEY DAVIDSON BIG TWIN SPIGET MOUNT CARBURETOR INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 26-03-2012

download
A. BEFORE INSTALLATION OF YOUR NEW ZENITH CARBURETOR, NSPECT THE RUBBER MANIFOLD SEAL FOR NICKS,CRACKS, OR DEBRIS. APPLYING A LIGHT FILM OF PETROLEUM BASED LUBRICANT AROUND THE INSIDE LIP OF THE RUBBER SEAL WILL ALLOW THE CARBURETOR TO SLIP INTO PLACE EASIER. B. BEFORE ACTUAL INSTALLATION OF UNIT INTO MANIFOLD, THROTTLE CABLES SHOULD BE HOOKED TO THETHROTTLEWHEEL.MAKESURETHATTHE PULL CABLE IS LOCATEDPROPERLY TO OPEN THE THROTTLE PLATE (IN SOME APPLICATIONS THROTTLE CABLE SLACK MAY NEED TO BE ADJUSTED FOR PROPER HOOKUP AND OPERATION) SEE FIG. #1 C. AFTER THROTTLE CABLES ARE PROPERLY HOOKED UP,UNITCAN BE INSERTED INTO MANIFOLD. MAKE SURE THAT UNIT IS FULLY SEATED. WITH CARBURETOR SEATED INTO MANIFOLD AND FUEL LINE HOOKED UP TO FUEL INLET, INSTALL CHOKE CABLE AND HOOK TO CHOKE LEVER. PLACE AIR INTAKE GASKET ON END OF CARBURETOR, NEXT PLACE INTAKE ADAPTOR OVER INTAKE GASKET. SEE FIG#2 ZENITH MOD.16P12 SPIGET MOUNT CARBURETOR -HARLEY DAVIDSON ™ BIG TWIN INSTALLATION INSTRUCTIONS FIG. # 1 FIG. # 2 D. WITH ADAPTOR IN PLACE, LOCATE THE STOCK AIR BOX OVER THE ADAPTOR, UTILIZING THE STOCK AIR BOX GASKET (THERESHOULDBENO GAPS BETWEEN ADAPTOR, AIRBOX OR CARBURETOR WHEN PROPERLY INSTALLED) STAND-OFF SPACERS PROVIDED ARE TOBEPLACEDBETWEENAIR BOX& ENGINE HEADS BEFORE INSTALLING THE VENT/RETAINING BOLTS. FOR EVALUATION ENGINES STOCK VENT BOLTS CAN BE USED WITH LARGERI.D. SPACER PROVIDED. SEE FIG#3 E. WITH AIR BOXSECURELY IN PLACE, INSTALL THE AIR FILTER COVER RETAINING BRACKET AND FILTER USING THE STOCKBOLTS, AND REPLACE AIR FILTER COVER AND SECURE WITH STOCK BOLT. SEE FIG#4 F. AFTER INSTALLATION IS COMPLETE AND FUEL FLOW HAS BEEN RE-ESTABLISHED, CHECK FOR ANY LEAKS BEFORE STARTING ENGINE. H. AFTER STARTING ENGINE, SOME ADJUSTMENTS OF IDLE AND MAIN JET MAYBE REQUIRED FOR PROPER OPERATION. AFTER ADJUSTMENTS HAVE BEEN MADE AND WITH ENGINEAT IDLE, TURN WHEEL FULLYTOLEFTANDRIGHT.ANYCHANGEIN IDLE SPEED INDICATES THROTTLE CABLES ARE TOO TIGHT AND MORE SLACK MUST BE PROVIDED.

Incoming search terms:

Incoming search terms: