diagram schematics for 2003 harley davidson electra glide front fork assembly

You search Auto repair manual PDF diagram schematics for 2003 harley davidson electra glide front fork assembly, if there are search results will appear below. If search results do not exist, please search by others keyword.



  diagram schematics for 2003 harley davidson electra glide front fork assembly Direct Download speed 5282 Kb/s

  diagram schematics for 2003 harley davidson electra glide front fork assembly Full Version speed 6162 Kb/s



HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

HARLEY DAVIDSON FL SOFTAIL PROFILE LOW FRONT SUSPENSION KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
Fork Spring Removal 1. Elevate and support the vehicle so the front tire is off the floor and the forks are fully extended. 4 9 3 1 10 11 2 5 6 7 8 is04004 1. Slider tube cap 2. Spacer washer 3. Oil seal 4. Clamp bolt and washer 5. Fork tube plug 6. O-ring 7. Fork spring 8. Tight-wound end of spring 9. Fork slider tube 10. Fork slider 11. Drain screw and washer Figure 1. Front Fork NOTE Remove the brake caliper from the fork slider. DO NOT remove the brake line from the caliper. 2. Remove the front wheel. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. 3. Remove the front fender. See FRONT FENDER in the Service Manual. 4. See Figure 1. Remove the slider tube cap (1), spacer (2) and oil seal (3) from the top of one fork side. Save the cap and spacer. The oil seal can be discarded. 5. Loosen the clamp bolt (4) and pull the fork from the brackets. 6. Repeat Steps 4 and 5 for the other fork side. -J00280 1 of 4 Wear saf ety glasses or gog gles when ser vicing f ork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) NOTE Be careful not to damage the O-ring. 7. See Figure 1. Remove the fork tube plug (5) and O-ring (6). Pull the spring (7) out of the slider tube (9). Remove the drain screw and washer (11), and drain the fork. Reinstall the drain screw and washer, and tighten to 52-78 in-lbs (5.9-8.9 Nm). 8. Repeat Step 7 for the other fork side. NOTE The Profile® Low Front Suspension Kit requires a different amount of H-D TYPE E FORK OIL than is listed in the Service Manual. NOTE Measure the oil level from the top of the fork tube with the fork spring removed and the fork fully compressed. 9. See FRONT FORK OIL in the Service Manual, but substitute the measures below. Fill the forks with Harley- Davidson TYPE E FORK OIL: • 1986 through 1999 models: •11.7 oz (345 cc) of oil, or •5.2 inch (132 mm) from top of oil level to top of tube. • 2000 and later models: •13.4 oz (396 cc) of oil, or •4.1 inch (104 mm) from top of oil level to top of tube. Fork Spring Installation 1. Insert a new Profile Low spring (7) from the kit into each slider tube (9), with the tight-wound portion (8) toward the bottom of the fork slider. NOTE Be careful not to damage the O-ring. 2. Install the fork tube plug (5) and O-ring (6) assembly into the slider tube and tighten securely. Be sure that one flat on each fork tube plug faces toward the inside of the fork. 3. Insert both fork side assemblies up through the slider covers, the fork stem and bracket, and the upper bracket. 4. Obtain two new oil seals (3), H-D Part Number 45733-48, and the spacer washers (2) and slider tube caps (1) saved earlier. Place an oil seal, followed by a spacer washer, onto each fork tube plug. 5. Insert the threads of a slider tube cap through each washer and seal, and into the fork tube plugs. Tighten to 40-60 ft- lbs (54.2-81.3 Nm). 6. Tighten the fork stem bracket clamp bolts (4) to 30-35 ft- lbs (40.7-47.5 Nm). 7. Install the front fender. See FRONT FENDER in the Service Manual. Install the front wheel and brake caliper. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. Jiffy Stand Removal/Installation 1. Move the jiffy stand to the retracted (up) position. Wear safety glasses or goggles when removing or installing spring. Spring tension can cause spring, attached components and/or hand tools to fly out which could result in death or serious injury. (00477c) 2. See Figure 3. Unfasten the jiffy stand leg spring (A) from the vehicle. Remove the hex bolt (B), lock washer (C), flat washer (D) and leg stop (E) from the threaded end of the jiffy stand leg. Discard the jiffy stand leg, but retain all other components. 3. Clean and inspect the jiffy stand attaching parts and mounting bracket for wear or damage. If parts replacement is necessary, refer to the Jiffy Stand section of your Service Manual for replacement procedures

Incoming search terms:

HARLEY DAVIDSON FX SOFTAIL FRONT LOWERING SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (T), lockwashers (S), flat washers (R) and axle cap from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) and spacer (O) from fork tube plug (B). Remove quad ring seal (D). Save bolt and spacer but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring -J03923 1 of 4 pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring (1). 11. Remove dust cover (E). 12. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 13. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 14. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). NOTE The lower stop (L) may come out with the damper tube or remain in the slider tube. Ensure that the lower stop is removed from the slider tube. 15. Remove the lower stop (L). 16. Remove damper tube (2) from fork tube. 17. Remove rebound spring (F) from damper tube. 18. Repeat Steps 1-17 for the opposite side fork assembly. Fork Assembly

Harley Davidson 39 mm Front Spring Lowering Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 07-04-2012

download
1. Support the motorcycle so the front wheel is off the ground. Next remove the front wheel and fender. Remove the fork cap nuts and loosen the lower triple clamp pinch bolts. Remove the front brake caliper. Some models have a tapered end to the fork tube. Extra effort will be required to remove the tube from the crown. Loosen the top fork cap 1 to 2 revolutions. Use a soft wood block or similar tool (that will not mark fork cap finish) and tap down with mallet to loosen fork tube from its tapered fit in top steering crown. Make sure fork pinch bolts are loose. To completely remove fork of this style, unscrew the fork cap entirely. 2. Slide both fork assemblies out of the triple clamps. Unscrew the top fork tube plugs. Remove the plugs and fork springs. CAUTION: Fork caps are under spring pressure and could cause serious injury. Drain the fork oil by turning the fork assemblys upside-down. 3. Next, bottom the fork tube into the fork leg. DO NOT extend the tube while you remove the allen bolt on the bottom of the fork leg. Turn the assembly upside-down and shake the damper rod and rebound spring out of the fork assembly. Again, DO NOT extend the tube during this. Extending the tube could dislodge the internal bottoming cone, which fits on the end of the damping rod, making it very difficult to reinstall the damper rod without complete fork disassembly. 4. FOR 1″ REDUCTION IN FORK LENGTH: You must first measure the length of the O.E.M. rebound spring. Depending on the model of the motorcycle, the length will either be 1″ or 2″ long. A. If you currently have a 1″ rebound spring, you need to replace it with the 2″ long LA Choppers rebound spring (included in the kit), then reinstall the damper rod in the fork tube. B. If you currently have a 2″ rebound spring, you will need to add the 1″ long spacer, then reinstall the damper rod in the fork tube.

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

HARLEY DAVIDSON DUAL DISC FRONT BRAKE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
This kit is designed for installation on the following models which have original equipment 39mm front fork tubes (including chromed tubes) and 19-in. cast-aluminum front wheels: • 2000 – 2003 XLH 883, XLH 883 Hugger and XLH 1200 • 2000 – 2003 FXD (Super Glide) This kit can also be installed on the above XLH and FXD models which have original equipment 39mm front fork tubes and 19-in. laced front wheels only after one of the following procedures is performed: • The original single-flange hub of the 19-in laced front wheel is replaced with a new double-flange hub (H-D Part No. 43629-00), (sold separately) which will accept the second brake disc. OR • The original 19-in. laced front wheel assembly, which has a single-flange hub, is replaced with a new 19-in. laced front wheel assembly (H-D Part No. 43579-00), (sold separately) which has a double-flange hub designed to accept the second brake disc. See the Service Parts Illustration for a list of the contents included in this kit. This kit does not include the front brake line required for a dual disc system; the brake line must be purchased separately as follows: • For XLH 883 motorcycle equipped with low-rise (flat) handlebars, order dual disc brake line H-D Part No. 45148-96. • For XLH 883 Hugger, XLH 1200, and FXD Super Glide models with “buckhorn” (pull-back) handlebars, order dual disc brake line H-D Part No. 45111-96. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) Brakes are a critical safety component. Contact a Harley- Davidson dealer for brake repair or replacement. Improperly serviced brakes can adversely affect brake performance, which could result in death or serious injury. (00054a) Removal and Disassembly – Front Brake System NOTE A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. 1. Block motorcycle underneath frame so that front wheel is raised off the ground slightly. 2. Remove original front brake caliper from left side of front fork according to appropriate Service Manual procedures. Let caliper hang loose on brake line. Save all components and fasteners for reinstallation. NOTE Do not operate the front brake lever with the front caliper removed because the piston may be forced from the caliper. Reseating the piston requires disassembly of the caliper . 3. Remove socket head screw which secures a clamp (retains front brake line) to underside of front fork lower bracket (lower triple clamp). Discard clamp and screw. 4. Remove screw, lockwasher, and clamp which secure front brake line to right rear side of front fork upper bracket (upper triple clamp). Save all components for reinstallation. 5. Remove right mirror and, if applicable, right turn signal lamp assembly from original front brake master cylinder casting. Save all components and fasteners for reinstalla- tion.

Incoming search terms:

HARLEY DAVIDSON FXST BLACK FORK SLIDER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION The fork sliders included in this kit install in the same way as the original equipment parts. NOTE Prior to installation of this kit, check the bores of the new sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s), and front wheel according to instructions found in the Chassis section of the appropriate Service Manual. NOTE On some models other parts will also need to be removed to access the front forks. See the Service Manual. 3. Drain and remove the front forks. See the Chassis Section of the Service Manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 4. Disassemble the front fork tubes according to instructions in the Service Manual, and replace the original fork sliders with the black sliders from the kit. 5. Assemble the front fork tubes, replacing worn seals, bushings or other additional items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 6. Tighten the drain screws to 52-78 in-lbs (5.9-8.8 Nm) 7. Fill with Harley-Davidson TYPE E FORK OIL according to the instructions found in the Service Manual. 8. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel, and caliper(s) according to the instructions found in the Chassis section of the Service Manual. Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Poor visibility of rider to other motorists can result in death or serious injury. (00336b) 1 is02733 1. Install bottom of reflector 2.0 inches above center of axle Figure 1. Reflector Placement NOTE The front reflectors located on both sides of the fork sliders will be removed, cleaned and installed on the new chrome fork sliders. 9. See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side to side until it can be removed. Retain reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. 10. Peel off any excess adhesive from both reflectors. Surface must be clean for reinstallation. 11. Peel off one side of backing on foam double sided tape. Press firmly on tape to secure it to reflector. Repeat double sided adhesive tape installation on remaining reflector. NOTE The bottom edge of reflector should be two inches (50 mm) above the center of the axle shaft. 12. See Figure 1. Remove second side (outside surface) of adhesive backing. Place reflector in position (1) and press reflector firmly into place to activate the adhesive. Repeat for remaining reflector. 13. Pump brakes prior to test riding vehicle.

Incoming search terms:

HARLEY DAVIDSON CHROME FORK SLIDERS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
REMOVAL 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s) and front wheel according to instructions found in the Chassis section of the appropriate service manual. NOTE On some models other parts will also need to be removed to access the front forks. See the service manual. 3. For All Models EXCEPT Touring: Drain and remove the front forks. See the service manual. 4. For Touring models equipped with air-adjustable suspension: Bleed the air-adjustable suspension according to the instructions in the appropriate service manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 5. For 2000 and Later Models EXCEPT Touring: See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side-to-side until it can be removed. Save reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. Peel off any excess adhesive from both reflectors . Surface must be clean for installation. 6. Disassemble the front fork tubes according to instructions in the service manual. INSTALLATION NOTES The chrome fork sliders included in this kit install in the same manner as the original equipment parts. Refer to the service manual for proper installation procedures. Prior to installation of this kit, check the bores of the new chrome sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Assemble the front fork tubes, replacing worn seals, bushings or other items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 2. Tighten the drain screws: •Early Models with 39 mm forks (see Figure 2): Tighten to 13-17 in-lbs (1.5-1.9 Nm) •Early Models with 41 mm forks (see Figure 2): Tighten to 52-78 in-lbs (5.8-8.8 Nm) •Later Models (see Figure 3): Tighten to 52-78 in-lbs (5.8- 8.8 Nm) 3. Fill with TYPE E FORK OIL (99884-80) according to the instructions in the service manual. 4. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel and caliper(s) according to instructions in the service manual. 5. For Touring models equipped with air-adjustable suspension: Refill the air-adjustable suspension system after assembly according to the service manual instruc- tions

Incoming search terms: