differences between the cbr f4i ecu units

You search Auto repair manual PDF differences between the cbr f4i ecu units, if there are search results will appear below. If search results do not exist, please search by others keyword.



  differences between the cbr f4i ecu units Direct Download speed 5282 Kb/s

  differences between the cbr f4i ecu units Full Version speed 6162 Kb/s



Honda CBR F4 or F4I 600cc Engine PE-ECU-1 System INSTALLATION

0

Filed Under (Honda) by admin on 05-01-2012

download
The PE-ECU-1 can be installed on virtually any 1,2,4,6 or 8 cylinder even-firing engine that requires fuel injection and/or ignition control. All of the functions of the ECU can be adjusted by using a laptop or PC running Windows. The following describes the basic requirements for using the system with a Honda 600cc F4 or F4I motorcycle engine. Please refer to the User’s Manual for a more in-depth description. Input Sensors The stock Honda F4 and F4I crank position sensors can be used with the PE-ECU-1 engine control system, provided the engine controller is configured for a 2- wire variable reluctance sensor. The configuration for the input is handled at the factory via a set of board jumpers. If the type of crank sensor should ever be changed, please contact PE for support on this issue. The stock Honda crank sensor should be wired according to the following: • Solid Yellow Wire – Pin 34 on ECU • Yellow with White Stripe (GND) – Pin 25 on ECU Failure to wire the sensor in this way may result in an engine that misfires and/or has incorrect ignition timing. The stock Honda trigger wheel cannot be used with the PE-ECU-1 system due to the differences in the number and spacing of the teeth. The PE-ECU-1 must be provided with a 12-1 pulse-train, correctly phased with TDC #1 according to Figure 1

Incoming search terms:

2001 – 2003 Prius 2003 4Runner, Camry, Land Cruiser and Sequoia VEHICLES EQUIPPED WITH TRANSPONDER ECU

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
When replacing the ECM (SAE term: PCM) or the Transponder ECU a “handshake” procedure must be performed. This ECU ID communication is necessary to enable the Transponder ECU and the ECM to recognize each other before the vehicle will start. Complete ECU communication using the following steps: 1. Insert a Master key into the ignition cylinder. 2. Turn the ignition ON (engine OFF). 3. Short Tc and CG terminals of DLC3 using the Diagnostic Check Wire (SST 09843-18020 or equivalent) and leave for 30 minutes. 4. After 30 minutes, turn the ignition OFF and remove check wire from DLC3. 5. Register any additional keys as necessary. 6. Start the vehicle to confirm successful ECU communication. Key Programming: To program or delete a key, a registered Master key is necessary unless the Transponder ECU has been reset or replaced. The Transponder ECU system incorporates a black “Master” key and a gray “Sub” key. The process during registration of these two keys is identical. The key itself now determines if it functions as Master or Sub, not the registration procedure. The maximum number of allowable Master and Sub keys vary by model. Refer to the chart below.

Incoming search terms:

Honda CBR-600 F4 / F4i – Installation Instructions (slip-on)

0

Filed Under (Honda) by admin on 11-11-2011

download
Remove the lower fairing. Remove the existing exhaust system from the middle of the stock pipe. Save the stock exhaust can mounting bolt and nut for the end can to the passenger footpeg for reuse as well. Remove the clamp from the stock exhaust system and save for reuse. Install the S-Bend to the rear of the stock head pipe. Reuse the stock clamp, but do not tighten at this time. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1 for details. Place the bands approximately 190-200mm from the edge of the end can. See figure 2 for details.
Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount
the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G.
Attach the supplied springs to fasten the end can to the S-bend pipe. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. Carefully align the two stainless bands K so that they are parallel to each other, and spaced prope rly on the can (refer to step 7 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system

Honda CBR 600 F4i 2004 – 2005 Bestem USA Fiberglass F13 Installation Guide

0

Filed Under (Honda) by admin on 20-11-2011

download
We highly recommend having a professional install this undertail. A dremel tool or nsimilar is what we found the best to cut plastics. Place bike on a rear wheel center stand. Remove passenger seat and hardware which secure stock undertail section Unplug the harness that connects tail light and remove the stock undertail. Position Bestem undertail close to the bike and determine the amount of plastic needs to be cut out. Use a dremel tool to carefully trim off plastics (glove boxes etc). This is the most time consuming part of the installation but your patience will be paid off. 5) Once the new undertail is slide in, determine holes need to be drilled (only on
certain models). Reuse the hardware for the stock undertail to secure the new undertail. 6) The wiring color codes from two round tail lights are Black Wire – Ground, connects to Ground wire. Red Wire – Brake Light, connects to brake light. Blue Wire – Running Light, connect directly to the running light. Orange Wire – Turn Signal, connect them to your L/R turn signal wires We highly suggest you solder the connections and use heat shrink wrap to seal the connections. Test your lights before going out for a ride, also make sure your new undertail is securely installed on the bike. Now it’s time to go out for a spin!

HONDA CB650/ 750F/ 900F/ 1100F/ GL1100 Spark Unit Set Installation Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
INSTALLATION INSTRUCTIONS: 1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the seat and/or petrol tank to gain access to the original spark units (if fitted); these are normally fitted under the seat between the top frame tubing. Each of these units consists of a small alloy metal box with sleeved wires terminated by a small connector (coupler). They also have a mounting tab with a single fixing hole. 3. On four cylinder machines there will be two units, normally mounted back to back; one for cylinders 1&4 and one for cylinders 2&3. 4. For safety, disconnect the battery. 5. Unplug the couplers from each of the units. Undo the fixings and remove the units. 6. Fit the new spark units in the place of the old ones or find a suitable alternative, close to the connectors. Secure the units to the frame or mounting platform using the supplied tie-straps and adhesive mounting base (if required). If required, a thin sheet of rubber or double-sided tape can be used to keep the units in position. Do not completely wrap the units in foam rubber. 7. Push the wiring harness plugs into the new spark unit socket connectors; they will only fit one way. Reconnect the battery. 8. If you are rewiring the machine or do not have the standard wiring harness, the spark unit wire colours & functions are as follows: GREEN Ö GROUND (0 VOLTS) BLACK/WHITE Ö IGNITION SUPPLY (+12 VOLTS) VIA ENGINE STOP SWITCH YELLOW Ö IGNITION COIL OUTPUT (TO COIL —) WHITE Ö PULSE GENERATOR (WHITE RING) BLUE Ö PULSE GENERATOR (UNMARKED) There are two pulse generators, one for cylinders 1&4 and one for cylinders 2&3. The left hand one is normally for cylinders 1&4 (see fig.1). There are two wires of the same colour coming from each pulse generator, one of these wires is normally marked with a white band. The pulse generator wire with the white band connects to the white wire from the corresponding spark unit, the other pulse generator wire connects to the blue wire on the corresponding spark unit. If the white band is missing, this is normally the upper wire coming from the pulse generator. 9. Refit the seat and tank (if removed earlier). 10. Fitting is now complete, although for best results you may wish to verify the ignition timing, see the following guide

Incoming search terms:

HONDA CB650/ CB750F/ CB900F/ CB1100F 4 CYLINDER TWO CABLE TIE ADHESIVE MOUNTING BASES REMOVAL

0

Filed Under (Honda) by admin on 29-11-2011

download
All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation.
2. Remove the seat and/or petrol tank to gain access to the original spark units (if fitted); these are normally fitted under the seat between the top frame tubing. Each of these units consists of a small alloy metal box with sleeved wires terminated by a small connector (coupler). They also have a mounting tab with a single fixing hole. 3. On four cylinder machines there will be two units, normally mounted back o back; one for cylinders 1&4 and one for cylinders 2&3. 4. For safety, disconnect the battery. 5. Unplug the couplers from each of the units. Undo the fixings and remove the units. 6. Fit the new spark units in the place of the old ones or find a suitable alternative, close to the connectors. Secure the units to the frame or mounting platform using the supplied tie-straps and adhesive mounting base (if required). If required, a thin sheet of rubber or double-sided tape can be used to keep the units in position. Do not completely wrap the units in foam rubber. 7. Push the wiring harness plugs into the new spark unit socket connectors; they will only fit one way. Reconnect the battery. 8. If you are rewiring the machine or do not have the standard wiring harness, the spark unit wire colours & functions are as follows

TOYOTA E ECU / COLD START INJECTOR TIME SWITCH MODIFICATION

0

Filed Under (Toyota Manuals) by admin on 17-10-2011

download
Before replacing an ECU or a cold start injector time switch, perform a thorough inspection to verify that all engine mechanical, fuel and electrical/electronic systems are to recommended specifications. PARTS RETURN INFORMATION: The replacement ECU’s are remanufactured by Nippondenso-Los Angeles (NDLA). In order to maintain cores for rebuilt units, the original ECU must be sent to NDLA as soon as it has been replaced.

Ducati 1098 and 1098S ECU connection Installation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
ECU can be connected to AIM loggers in two different ways: directly, or using the connector placed on the dashboard. 2.1. – Direct connection between AIM loggers and Marelli IAW 5AM2 ECU IAW 5AM2 is equipped with two 38 pins connectors, named “Body ” and “Engine” – see below: “engine” is black (on the left). “Body” connector is grey (on the right). To connect AIM loggers to Ducati ECU: • connect AIM cable labelled CAN+ to pin 20 of “Body” connector. • connect AIM cable labelled CAN- to pin 29 of “Body” connector. • Vbatt is on pin 17 (vehicle master switch). 2.2 – Dashboard connector Connector is equipped with 26 pins and it is placed on the back of the dashboard. To connect AIM loggers to ECU using the dashboard connector: • connect AIM cable labelled CAN+ to pin 19 (green/black twisted cable) connector. • connect AIM cable labelled CAN – to pin 26 (grey/green twisted cable) connector. • Vbatt is on pin 23 – red /black cable – vehicle master switch. Warning: to use Marelli dashboard , please remove 120 OHM resistance placed between CAN+ and CAN-; otherwise Marelli dash does not work

1997 Honda CBR 1000 F specifications

0

Filed Under (Honda) by admin on 03-11-2010

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes. Pictures, trademarks and logos of third parties are exclusive property of the respective owners. Technical specifications are subject to change without notice. Bikez.com has been developed by low-cost software development company ObjectLabs

1997 Honda CBR 1000 F specifications review

0

Filed Under (Honda) by admin on 20-12-2011

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes.

Incoming search terms: