distributors and manufacturers of circuit breakers in china mail

You search Auto repair manual PDF distributors and manufacturers of circuit breakers in china mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





2001 YAMAHA TDM900 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 20-11-2010

download
CHECKING THE SWITCHES ELEC EAS00731 ELECTRICAL CHECKING THE SWITCHES Check each switch for damage or wear, proper connections, and also for continuity between the terminals. Refer to “CHECKING SWITCH CONTINUITY”. Damage/wear Repair or replace. Improperly connected Properly connect. Incorrect continuity reading Replace the switch. -3- ELECTRIC STARTING SYSTEM ELEC EAS00755 ELECTRIC STARTING SYSTEM CIRCUIT DIAGRAM -4- ELECTRIC STARTING SYSTEM ELEC 4 Main fuse 5 Battery 7 Starter relay 8 Starter motor 9 Main switch 12 Starting circuit cut-off relay 13 Sidestand switch 14 Neutral switch 49 Clutch switch 59 Engine stop switch 60 Start switch 61 Ignition fuse -5- ELECTRIC STARTING SYSTEM ELEC EAS00756 STARTING CIRCUIT CUT-OFF SYSTEM OPERATION If the engine stop switch is set to “” and the main switch is set to “ON” (both switches are closed), the starter motor can only operate if at least one of the following conditions is met: The transmission is in neutral (the neutral switch is closed). The clutch lever is pulled to the handlebar (the clutch switch is closed) and the side- stand is up (the sidestand switch is closed). The starting circuit cut-off relay prevents the starter motor from operating when neither of these conditions has been met. In this instance, the starting circuit cut-off relay is open so current cannot reach the starter motor. When at least one of the above conditions has been met the starting circuit cut-off relay is closed and the engine can be started by pressing the starter switch. WHEN THE TRANSMISSION IS IN NEUTRAL WHEN THE SIDESTAND IS UP AND THE CLUTCH LEVER IS PULLED TO THE HANDLEBAR 4. Starting circuit cut-off relay Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) and battery (12 V) to the starting circuit cut-off relay terminals as shown. YES NO Replace the starting circuit cut-off relay. Does the starting circuit cut-off relay have continuity between blue/white and black? EAS00759 Continuity Tester positive probe sky blue Tester negative probe blue/yellow No conti- nuity 1 2 1 3 Tester positive probe sky blue Tester negative probe black/yellow Battery positive terminal red/black Battery negative terminal black/yellow 1 2 Tester positive prove blue/white Tester negative prove black 3 4 5. Starting circuit cut-off relay (diode) Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) to the starting circuit cut-off relay terminals as shown. Measure the starting circuit cut-off relay for continuity as follows. Tester positive probe blue/green Tester negative probe blue/yellow 4 3 Tester positive probe black/yellow Tester negative probe sky blue 2 1 Tester positive probe blue/yellow Tester negative probe sky blue 3 1 Tester positive probe blue/yellow Tester negative probe blue/green 3 4 When you switch the tester’s positive and negative probes, the readings in the above chart will be reversed. Are the testing readings correct? YES NO Replace the starting circuit cut-off relay. NOTE: EAS00760

Incoming search terms:

HARLEY DAVIDSON DETACHABLE TOUR-PAK LIGHT HARNESS KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 2. ALL models: Install the Detachable Tour-Pak Rack Kit per the instructions in that kit, up to the point where the saddlebags are to be re-installed. NOTE Make note of the cable strap locations before releasing the harness from the upper frame tube. New straps will be fastened in the same location. 3. Cut the larger cable strap fastening Tour-Pak circuit [12] (see the Service Manual Wiring Diagram) of the vehicle main harness to the left-side upper frame tube, rearward of the shock absorber. Cut the small cable strap at the end of the circuit [12] conduit. 4. Slit the conduit open along its length to expose the final ten inches (0.25 M) of main harness circuit [12] wiring. Cut the three wires (Black, Blue, and Red with Yellow tracer) nine inches (0.23 M) from the three-way Multilock socket housing [12B]. The socket housing and cut wires can be discarded. 5. Obtain the socket housing, secondary lock (locking wedge), and three socket terminals from the kit. See the illustration at DEUTSCH ELECTRICAL CONNECTORS: REMOVING/INSTALLING SOCKETS in the Service Manual. Refer to CRIMPING INSTRUCTIONS in the Service Manual, and follow the instructions to install the terminals to the three wire leads of main harness circuit [12]. 6. Per the instructions under DEUTSCH ELECTRICAL CONNECTORS, insert the Blue lead and terminal into Cavity 1 of the new socket housing. Insert the Red/Yellow lead and terminal into Cavity 2. Insert the Black lead and terminal into Cavity 3. 7. Cut the excess conduit from main harness circuit [12]. 8. Obtain the two cable straps from the kit. As noted in Step 3, use one strap to bind the end of the main harness circuit [12] conduit. Use the second strap

YAMAHA FZR 400 ELECTRICAL CIRCUIT DIAGRAM

0

Filed Under (Yamaha) by admin on 29-11-2010

download
CHECKING OF SWITCHES Check the switches for the continuity between the terminals to determine correct connection. Read the following for switch inspection. SWITCH CONNECTION AS SHOWN IN MANUAL The manual contains a connection chart as shown left showing the terminal connections of the switches (e.g., main switch, handlebar switch, brake switch, lighting switch, etc.) The extreme left column indicates the switch positions and the top line indicates the colors of leads connected with the terminals in the switch component. “C’&-0″ indicates the terminals between which there is a continuity of electricity; i.e., a cl.osed circuit at the respective switch positions. In this chart: “R and Br” and “L/W and L/R” are continuous with the “ON” switch position. “B and B/W” is continuous with the “OFF” switch position. “B and B/W” is continuous with the “LOCK” switch position. “B and B/W” and “R and L/R” are continuous with the “P” switch position. CHECKING SWITCH FOR TERMINAL CONNECTION Before checking the switch, refer to the connection chart as shown above and check for the correct terminal connection (closed circuit) by the color combination. To explain how to check the switch, the main switch is taken for example in the following

KTM 125 SX, EXC 200 EXC, XC, XC-W 250 SX, EXC, XC, XC-W 300 EXC, XC, XC-W OWNER'S MANUAL

0

Filed Under (KTM) by admin on 27-11-2010

download
Short circuit button (SX) The short circuit button [1] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Combination switch (EXC) The light switch has 2, respectively 3 switch positions. [A] = Light off (this function is not available in all models) [B] = Low beam on [C] = High beam on You may use button [2] to actuate the horn. The red short circuit button [3] serves to switch off the engine. Leave the switch pressed until the engine stops. Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [4] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Emergency OFF switch (Australia) The emergency OFF switch [5] is located next to the throttle grip. Primarily designed as safety or emergency OFF switch, it should normally not be in its activated state. In this position, the ignition circuit is shorted; if the engine is running, it will stall immediately, if it is at standstill, it will not start. In this position, the ignition circuit is enabled; the engine should start. 1 2 3 5 A B C 4
ENGLISH 12 Filler cap To open it: turn filler cap counter-clockwise. To close it: put filler cap back on and tighten it by turning it clockwise. Install tank breather hose [1] without kinks. Filler cap (XC, XC-W) To open the filler cap: Turn the filler cap 45 ° counter-clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carbure- tor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. With the twist grip in this position the tank will be emptied until only the reserve is left. RES The reserve tank cannot be tapped until the rotating handle is turned to the RES position. Fill the tank as soon as possible and remember to turn the rotating handle back to the ON position so that you will have backup fuel next time, too. Reserve of the 8.5 l tank . . . . . . 1.3 l (0.32 USgallons) Reserve of the 10 l tank . . . . . .1.7 l (0.45 USgallons

1995 Camry WIPER MOTOR CIRCUIT BREAKER INSPECTION PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 15-10-2011

download
INSPECTION PROCEDURE: Inspect the Wiper Fuse. Verify there is power and ground to the Wiper Motor on all speeds (including “Intermittent” or “Mist” if applicable). After verifying power and ground to the Wiper Motor, follow the procedure below to prevent unnecessary Wiper Motor replacement because of a temporary open in the Wiper Motor Circuit Breaker. 1) Disconnect the Wiper Motor Harness Connector. 2) Wait (10) minutes before checking continuity. 3) Check the continuity of the motor with an ohmmeter. REPRESENTATIVE CHECKING PROCEDURE: NOTE: Continuity check can be performed between either the low speed or high speed terminal and the ground terminal of the wiper motor. The standard resistance of a good wiper motor is approximately 1.5 to 4.5 ohm

Incoming search terms:

Honda Shadow Aero 750 Turn Signal Cancellation Unit Installation Procedures

0

Filed Under (Honda) by admin on 29-11-2010

download
Left TurnSignal Right TurnSignal Turn Signal Switch (for ref. Only) CIRCUIT CONNECTIONS AFTER INSTALLATION of Cancellation Unit Original+12 volts motorcycle supply power for flasher Ground (thiswiredoesnot exist on all models) Output to switch Power Power Red Yellow Gray Green Ground Green/Red Blue/Red Turn Signal Cancellation Unit Identify the positive power wire to the turn signal flasher. A test light with the probe touched to this wire will stay on steady and flash with the turn signals. Cut the wire and install the connectors observing the polarity as shown. Connect the Red and Yellow wires as shown. not Identify the flasher output wire to the signal switch and attach the gray wire by soldering or use the supplied red tap connector. Place the unit in a suitable area on your particular motorcycle. It is suggested under the seat providing access to the turn signal flasher. Connect the units ground (green) wire to frame (neg) ground Assure it’sareliable connection. IF THE GROUND WIRE BECOMES DISCONNECTED THE UNIT WILL BURN UP. using the supplied ring terminal. Identify the brake light circuit per the motorcycle wiring diagram. Using a test light verify the correct circuit using the following procedure. Connect the test light alligator clip (negative side) to frame ground. Using the positive tip probe the circuit. The proper circuit will illuminate the the brake is applied. Attach the Green/Red wire to this circuit. test light when The factory cancellation time is set at approximately 23 flashes. The length of time for cancellation can be decreased to approximately 15 counts by setting the program listed in the programming box

Incoming search terms:

Yamaha XVS13AW SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10540 ON All electrical circuits are supplied with power, and the meter lighting, taillight, license plate light and position lights come on, and the engine can be started. The key cannot be removed. NOTE: The headlight comes on automatically when the engine is started and stays on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. WARNING EWA10060 Never turn the key to “OFF” or “LOCK” while the vehicle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the vehicle is stopped before turning the key to “OFF” or “LOCK”. 1. Push. 2. Turn. 1. Push. 2. Turn. INSTRUMENT AND CONTROL FUNCTIONS 3-2 3 EAU11003 Indicator and warning lights EAU11020 Turn signal indicator light “” This indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU42740 Fuel level warning light “” This warning light comes on when the fuel level drops below approximately 3.7 L (0.98 US gal) (0.81 Imp.gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, and then go off, have a Yamaha dealer check the electrical circuit. NOTE: The vehicle must be on a level surface and positioned upright, otherwise the fuel level warning light may not come on and go off at the appropriate times. This model is also equipped with a self-diagnosis device for the fuel level detection circuit. If the fue

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms:

motorcycle Turn Signal Conversion Kit Installation Instructions

0

Filed Under (Tips and Review) by admin on 09-11-2010

download
1. Place motorcycle on solid, level ground and on center stand if equipped. 2. Remove your turn signal lens. Place it upside down and clean the lens interior with the supplied alcohol wipe. Allow to completely air dry. Note: the LEDs are mounted to the inside of the turn signal lens with the LEDs making direct contact with the lens. The supplied silicone is used to secure the LED board to the lens. It remains flexible but can be removed. Test fit the board in your lens prior to using silicone. 3. Using a small screwdriver, poke a small hole in the end of the tube of silicone. Place a dab of silicone on each of the 12 LEDs on the circuit board. CAUTION : Note the position of the metal pins on the back of the LED board, They must be located 90 degrees from where the holes are that secure the lens to the housing. See attached diagram. 4. Position the round circuit board over the inside of your turn signal lens with the LEDs facing down. Get the board as centered as possible. Allow the silicone to make contact with the inside of the lens and then push down and slightly rotate the board back and forth to allow the LEDs to make contact with the lens surface. Repeat other side. NOTE : the silicone will require 30 minutes in 70 degree weather to tack up. Full cure will occur within 24 hours. We suggest not riding for several hours if possible to allow the best adhesion. 5. You will need to access the following wires; running light (license plate can be used), brake lights, right turn and left turn. Disassemble the bike as needed to gain access to the wiring. Shop Tip: we have found that on the Yamaha Star Series and the Kawasaki Cruisers that installation is much easier when you remove the turn signal bar from the fender. On the Yamahas, there are 3 bolts holding the moustache in position. The wires will unplug from behind the license plate. On the Kawasakis, unplug the signals under the seat and bend the tabs under the fender to be able to remove the wires. 6. We have provided some tubing to slide over the wires so that when you re-install the bulb socket, our wires for the LED boards will not be pinched. This tube should be slid all the way into the turn signal housing. You may have to shorten the tubing for your installation. 7. You will need to run wires through the stem of the turn signal. You can see samples of how the various manufacturers signal housings come apart on our web site. Click on “Other Lighting Products” and then “Turn Signal Conversion Kits” and follow the link. We suggest placing the removed turn signal assembly on a towel on your work area. 7. You will need to leave 2″ of slack in the wires at the turn signal housing to allow for wire connection. 8. Reinstall the turn signal housing back on the motorcycle if removed. NOTE: both of the run/brake circuits must be used. You may shorten the wires only on the run/brake circuits as needed. Do not change the circuits under the heat shrink. T-Tap instructions. Lay the “donor” wire in the slot in the burgandy connector. Close and snap together with pliars. Strip some insulation off of the wire which will be tapping into the factory wire. Crimp one of the pink connectors on the bare wire and plug it into the burgandy T-Tap 9. Connect the green wires from the run/brake circuits to the bikes running lights. The 2 greens can be connected together. 10. Connect the blue wires from the run/brake circuits to the bikes brake lights. The 2 blues can be connected together. 11. Take one of the red wires from a run/brake circuit and connect it to one of the black with white stripe wires coming from one of the LED boards using the supplied red butt connector. Connect the other run/brake circuit red wire to the remaining black with white stripe wire on the other LED board. 12. Connect the black wire from the LED board on the right side of the bike to the right turn signal positive (+) wire on the motorcycle. 13. Connect the black wire from the LED board on the left side of the bike to the left turn signal positive (+) wire on the motorcycle. 14. Plug the wires into the LED boards. If you hold the turn signal lens so that you are viewing the back of the LED board, position the connectors on the board at the 12 o’clock (top) position. The connector on the left is the positive (+) terminal. Connect the red wire to it. Connect the black wire to the remaining connector on the right side. 15. Check operation. LEDs should come on with running lights. LEDs will brighten when brake lights are applied. LEDs will shut off when the amber turn signal comes on. 16. Should you have any problems, please see the troubleshooting chart on our website.* * 17. Reassemble bike

Incoming search terms:

YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

Incoming search terms: