distributors of electric bulb in china mail

You search Auto repair manual PDF distributors of electric bulb in china mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

2008-2009 KAWASAKI TERYX HEADLAMPS HIDTERYX HID KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
a. Remove rubber boot from the back of the headlamp housing assembly. b. Push down on metal latch and pull away from lip to release halogen bulb. Pull out halogen bulb. c. Insert HID bulb, line up bulb to fit into the bulb holder, lower latch to lock bulb in place. d. Replace Rubber boot on the back headlamp assembly. (Make sure to pull wires through the center of the rubber boot first before you start to pull down boot on the back of the headlamp assembly.) e. Make sure that the wiring, coming from the HID bulb, clears the black plastic housing that encases the headlamp assembly so connection from the bulb to the ballast is possible. If installed correctly there is no need for drilling or modifications of any type. 2. Ballast a. Mount ballast in location of your choice – recommended near the headlight. 3. Wiring Note: DO NOT modify the wiring that runs from the HID bulb to the ballast. It will cause the system to work improperly. It will void the warranty . a. Once ballast is installed connect corresponding wires from HID bulb to corresponding male / female plugs on ballast. b. To connect wiring from ballast to Teryx primary system i. Find wire extension with white triangular head with black, yellow & green wires at opposite end ii. Connect black off extension to black wire coming off ballast iii. Connect Yellow / Green wire to red wire coming off ballast iv. Connect triangular head to corresponding plug on Teryx Factory Wiring End

Incoming search terms:

Vespa GTS Super Specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Gts super 300 ie Gts super 125 ie s 125cc s 50cc Gts 250 ie Gts 125cc LX 125cc LX 50cc 2 stroke Engine Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder LEADER 4 stroke with electronic injection Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder, catalised, LEADER 4 stroke, 4 valve Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Capacity 278cc 124cc 124cc 50cc 249cc 124cc 124cc 49cc Power 16.4 kW / 7500 rpm 10.5 Kw / 9500 rpm 7.65 Kw / 8250 rpm 3.2 Kw / 7500 rpm 15.7 Kw / 8500 rpm 7.65 Kw / 8250 rpm 7.65 Kw / 8250 rpm 2.5 Kw / 8500 rpm Max Torque 22Nm / 6500 rpm 12 Nm / 8000rpm 9.6 Nm / 7250 rpm 4.4 Nm / 6500 rpm 20.1 Nm / 6500 rpm 9.6 Nm / 7250 rpm 9.6 Nm / 7250 rpm 3.3 Nm / 6500 rpm Cooling Liquid Liquid Forced Air Forced Air Liquid Liquid Forced Air Forced Air Starter Electric Electric Electric and kick starter Electric and kick starter Electric Electric Electric and kick starter Electric and kick starter Transmission Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Front Suspension Single arm, dual chamber hydraulic shock absorber with coaxial spring Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Rear Suspension Two dual effect shock absorbers with adjustable preload Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Twin hydraulic shock absorbers with preload adjuster Twin hydraulic shock absorbers with preload adjuster Hydraulic shock absorbers with preload adjuster Hydraulic shock absorber Front Brake ø 220mm disc brake 220mm disc brake ø 200mm disc brake ø 200mm disc brake ø 220mm disc brake ø 220mm disc brake ø 200mm disc brake ø 200mm disc brake Rear Brake ø 220mm disc brake 220mm disc brake ø 110mm drum brake ø 110mm drum brake ø 220mm disc brake ø 220mm disc brake ø 110mm drum brake ø 110mm drum brake Front Tyre Tubeless 120/70-12″ Tubeless 120/70 – 12″ Tubeless 110/70 – 11″ Tubeless 110/70 – 11″ Tubeless 120/70-12″ Tubeless 120/70-12″ Tubeless 110/70 – 11″ Tubeless 110/70-11″ Rear Tyre Tubeless 130/70-12″ Tubeless 130/70 – 12″ Tubeless 120/70 – 10″ Tubeless 120/70 – 10″ Tubeless 130/70-12″ Tubeless 130/70-12″ Tubeless 120/70 – 10″ Tubeless 120/70-10″ Running weight 158kg 158kg 114kg 96kg 151kg 145kg 114kg 96kg Length/Width/Height 2230mm / 755mm / 1170mm 1930mm / 755mm / 1930mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm 1930mm / 755mm / 1170 mm 1940mm / 755mm / 1180 mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm Fuel Tank Capacity 9 litres 9 litres 8.5 litres 8.5 litres 9.2 litres 10 litres 8.5 litres 8.5 litres Emmissions Euro 3 Euro 3 Euro 3 Euro 2 Euro 3 Euro 3 Euro 3 Euro 2 Colours Rosso Dragon Nero Lucido Montebianco Rosso Dragon Nero Lucido Montebianco Taormina Nero Lucido Montebianco Taormina Nero Lucido Montebianco Marrone Terra Di Toscana Bronzo Perseo Nero Vulcano Blu Midnight

Incoming search terms:

HARLEY DAVIDSON HIGH INTENSITY DISCHARGE (HID) DUAL BULB HEADLAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Remove seat according to the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. 2003-Earlier Models: Disconnect battery cables, negative (-) cable first. Refer to the service manual. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 3. 2004-Later Models: a. Remove left saddlebag. Refer to the service manual. b. Remove left side cover and main fuse. Refer to the service manual. 4. Remove fuel tank according to the instructions in the service manual. 5. See Figure 1. Remove the Phillips screw (1) at the bottom of the bezel and remove the bezel. Save parts for installa- tion. 1 2 is03916 1. Phillips screw 2. Bezel Figure 1. Remove Bezel 6. See Figure 2. Remove and save Phillips screws (1) that secure mounting ring assembly (2) to nacelle. 7. Gently pull headlamp assembly out far enough to disconnect wiring. Save short wire harness for installation. 8. Remove wire connector at the back of the headlamp bulb. 9. See Figure 2. Remove three screws (3) securing the retaining ring (4) and headlamp assembly to mounting ring assembly. Discard mounting ring assembly, but save three screws and retaining ring for installation

Incoming search terms:

YAMAHA FJR1300N PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 17-12-2010

download
Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constant- voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery. EAU04076* Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 1. Fuel injection system fuse 2. Spare fuel injection system fuse 1. Headlight fuse 2. Signaling system fuse 3. Ignition fuse 4. Windshield motor fuse 5. Radiator fan fuse 6. Backup fuse (odometer and clock) 7. Spare fuse (〈 4)
PERIODIC MAINTENANCE AND MINOR REPAIR 6-31 6 EC000103 CAUTION: Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. EAU04099 Replacing a headlight bulb This motorcycle is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. 1. Remove panel B (if replacing the left headlight bulb) or panel C (if replacing the right headlight bulb). (See page 6-7 for panel removal and installation procedures.) 2. Disconnect the headlight coupler, and then remove the headlight bulb cove

Incoming search terms:

HARLEY DAVIDSON VRSC TURN SIGNAL RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Removing Turn Signals To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove the 40 amp Maxi-Fuse or disconnect the battery cables, negative cable first. Never touch the quartz bulb. Fingerprints will etch the glass and decrease bulb life. Grab the bulb with paper or a clean, dry cloth. Failure to do so could result in bulb damage. (00210a) 2. For VRSCA models, remove headlamp assembly. For VRSCB models, continue to Step 4. a. While facing the headlamp from behind (looking toward front of motorcycle), reach behind the headlamp bucket and twist the headlamp bulb approximately 45 degrees counterclockwise, then gently pull straight out of the headlamp. Repeat for remaining bulb. Temporarily secure bulbs out of the way for the following steps. b. See Figure 1. Remove the two mounting screws securing the headlamp bracket to the upper triple clamp and remove headlamp assembly. Save hard- ware

KAWASAKI MULE Electric Steering Installation Manual And Removal

0

Filed Under (Kawasaki) by admin on 05-05-2012

download
Remove plastic center cap on steering wheel by prying off with a small screwdriver. Remove steering wheel nut and remove steering wheel by pulling up on wheel. If wheel is tight have a partner tap on the shaft while pulling up on wheel. Note: Do not mushroom threads on shaft. Remove all screws that retain dash to body of vehicle. Disconnect all electrical connections at back of dash. Mark all wires to ensure easy install. Remove lower steering shaft bolt at rack and pinion. Remove upper bolt at base of steering column. Remove the 2 bolts that retain the steering column to the frame and remove the column and the shaft assembly. Remove lower u-joint on steering column shaft & replace it with supplied u-joint. There is a welded wire retainer on the lower dash tube where the electric motor will sit. You will need to grind off this piece and smooth. Remove the master cylinder bolt closest to the driver side and discard bolt. Your motor and module has been shipped together bolted to the bracket. It is important to follow the install sequence to ensure a proper installation. The lower shaft on the steering motor is marked on the shaft and on the motor. These marks must not be changed. If you remove the shaft it needs to be installed back in the same spot.

Incoming search terms:

2004-2007 Kawasaki Ninja ZX10 HID Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The hole made with a dremil, must be large enough for the main power wire to fit. The hole must be no more than an inch in diameter. The trick is to make the hole about ¾ of an inch to an inch and insert the wire diagonally to avoid creating a larger hole. If needed, make the hole larger on opposite sides only to create extra space for the power connectors. Push the rest of the wires through the hole, along with the rubber grommet. Then from the opposite side push the grommet into the dust cover, splitting sides to fit it over the hole. If installed properly, this is how the grommet should cover the hole that you made in the dust cover. One bulb prepped for installation. Both bulbs ready for installation. Take off the power plug from the original bulb Take out the original bulb and install the HID bulb. Be careful, not to touch the HID bulb at any time. Plug in the power wires into the original power plug. They go in easy and slide right in. Black wire connects into the black wire on the plug. On the right side, pink goes to red. On the left side, blue goes to red as these are positive wires. Pull the wires toward you slowly and carefully as you near the cover toward the headlight. Spin the rubber grommet if you need to line up the dust cover to the head light. Now lock it in. The arrow should point up if it is locked in properly

VICTORY HAMMER, KINGPIN, VEGAS AND JACKPOT ELECTRIC HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Victory) by admin on 29-01-2011

download
1. Remove the left and right plastic side covers and the seat (two allen bolts located below the sides of the seat). Unplug and remove the stock horn (located over the oil cooler). Connect the female ends of the jacketed two wire cable supplied to the original horn wires. Route the other end of the cable up over the engine and back to where the relay will mount as shown in photo (1). 2. Using the relay supplied with this kit and the wiring diagram provided with the horn set, identify the terminals of the relay (there are very small numbers next to each of the terminal). Connect the two (2) wires from the cable to terminals #85 & 86 on the relay. Locate the fuse holder wire assembly supplied and connect the blade terminal to the relay terminal #87 or #30. Connect the other end of the fuse wire to the battery positive terminal (+). 3. Working under the left side of the motorcycle, refer to photo (2) and install the black bracket supplied as shown onto the engine mount. Locate the four thin flat brackets and two (2) 6mm nuts supplied with the horn set and two lock washers supplied with the kit. Bolt two (2) of the brackets to each of the horns using a lock washer and 6mm nut on each and make them snug. Using the remaining 6 x 12mm bolt, nut and lock washer install the horns onto the black bracket and align as shown in photo (3). Adjust the horn location so that they are free to vibrate and do not come in contact with other parts of the motorcycle then tighten all three 6mmm bolts securely. 4. Using the two remaining wire assembles supplied, connect the larger terminals with double wires to one of the horns and the terminals with the single wire to the other horn. Route these wires up thru the frame to the relay. Connect the wire with the female blade connector to the relay terminal #30 or #87. Connect the ring terminal to the battery negative (-) terminal
or any 6m bolt on the frame. Turn on the ignition and test the horns. Secure the relay to the frame or other wiring and all loose wires using the cable ties supplied. Replace the seat and side covers

TRIUMPH ROCKET III ELECTRIC HORN HARDWARE KIT INSTALLATION

0

Filed Under (Triumph) by admin on 24-12-2010

download
1. Remove the seat and left hand side cover. (held in place by two (2) 10mm bolts) Remove the chrome cover from the stock horn located below the headlights. (held in place by two (2) 5mm allen screws at the top of the cover) 2. Unplug the wires from the stock horn. Locate the supplied jacketed cord and attach the end with the piggyback jumpers to the horn wires. Plug these back onto the horn terminals as shown in photo (1). Remove the black plastic left side steering head frame cover (held in place with two (2) 5mm allen screws). Route the cord behind the headlights, along the left side of the frame and over the engine keeping it neatly out of sight. Route the end if the cord to where the relay will mount as shown in photo (2A). Replace chrome horn cover and steering head frame cover. 3. Using the relay supplied, refer to the wiring diagram included with the horn set and the small numbers next to the terminals on the relay. Connect the 2 wires from the jacketed cord to terminals #85 & #86. Connect the blade terminal of the fuse wire assembly (supplied) to terminal #30 on the relay. Attach the other end of the fuse holder to the positive (+) battery terminal. 4. On the horns bend the wire terminals outward so that they will be parallel to the mounting brackets when installed. Refer to photo (3) and assemble the horns onto their supplied mounting brackets as shown. Bolt two (2) of the four (4) flat silver brackets on each of the horns using the 6mm nuts and lock washers supplied. Bolt the black bracket to the left hand horn using the 6x12mm bolt and nyloc nut supplied. Place the 6 x 35mm bolt with a washer and lock washer thru the right hand horn bracket then the left hand black bracket and place the 3/8″ flange nut over the back of the bolt. Remove the bolt where the horns will mount (see photo 2B) and bolt the horn set on as assembled with the flange nut on the back side of the black bracket. Align the horns as shown in photo (2) being careful that the horns do not make contact with each other or any other parts as this will significantly reduce their output then tighten the bolt securely.

Incoming search terms: