dna master cylider

You search Auto repair manual PDF dna master cylider, if there are search results will appear below. If search results do not exist, please search by others keyword.



  dna master cylider Direct Download speed 5282 Kb/s

  dna master cylider Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME MASTER CYLINDER AND CLUTCH BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
MASTER CYLINDER REMOVAL See Figure 1. Master cylinders designed for dual disc (two caliper) operation have an 11/16 inch (17.5 mm) bore, while those that are designed for single disc (one caliper) operation have a 9/16 inch (14.3 mm) bore. The bore size is stamped (1) on the master cylinder assembly inboard of the handlebar clamp bracket. NOTE Do not use an 9/16 inch bore master cylinder assembly on dual disc (two caliper) models or dual disc 11/16 inch bore master cylinder assembly on single disc (one caliper) models. These master cylinder assemblies are not interchangeable. Using the wrong assembly can adversely affect braking efficiency or result in brake failure which could result in death or serious injury. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1 is 01230 1. Bore stamp size location Figure 1. Verify Correct Master Cylinder Bore Size 1. Open bleeder nipple caps on front brake caliper. Install end of a length of clear plastic tubing over caliper bleeder valves, while placing free end in a suitable container. Open bleeder valves about 1/2-turn. Pump brake hand lever to drain brake fluid. Close bleeder valve. Avoid leakage. Be sure gaskets, banjo bolt(s), brake line and master cylinder bore are clean and undamaged before assembly. (00322a) 2. Remove bolt and two steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 3. See Figure 2. Place the cardboard insert between the brake lever and lever bracket

Incoming search terms:

HARLEY DAVIDSON CHROME FRONT BRAKE MASTER CYLINDER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. See Figure 2. Drain the brake fluid. a. Open bleeder nipple cap on front brake caliper. b. Install end of a length of clear plastic tubing over caliper bleeder valve, while placing free end in a suitable container. c. Open bleeder valve about 1/2-turn. d. Pump brake hand lever to drain brake fluid. e. Remove cover. f. Close bleeder valve. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 2. Remove bolt and 2 steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) is 01010 Figure 3. 5/32 in. (4 mm) Cardboard Insert 3. See Figure 3. Place the cardboard insert between the brake lever and lever bracket. 4. Using T27 TORX® drive head, remove the 2 screws with flat washers securing the handlebar clamp to the master cylinder housing. Remove the brake lever/master cylinder assembly and clamp from the handlebar. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. Remove retaining ring from pivot pin groove at bottom of master cylinder bracket. 6. Remove pivot pin and brake hand lever from master cylinder assembly. NOTE New master cylinder comes with all internal components preassembled. It is not necessary to remove the components from the bore of the old master cylinder. See Figure 9. Use denatured alcohol to clean clutch system components. Do not use mineral-based solvents (such as gasoline or paint thinner), which will deteriorate rubber parts even after assembly. Deterioration of these components can cause clutch failure, which could result in death or serious injury. (00296a) 7. With denatured alcohol, clean and inspect all parts that will be reused. Replace as necessary and wipe dry with a clean lint free cloth

Incoming search terms:

Yamaha Road Star Forward Control Kit Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Before starting to assemble this forward kit on your motorcycle check the packing list to make sure that the kit you received is the correct one for your model motorcycle and that the foot pegs are the style you ordered (billet or ISO). Next check the contents hardware kit P.N.0109-1000 against the packing list for completeness. Installing The Shift Control Photo 1 Remove wires from horn. Remove the two hex head bolts (Save for later installation) that mount the OEM shift controls to your motorcycle. Unthread stock shift rod at trans shift arm, leaving OEM rod end connected to stock shift arm. Using Original Metric hardware, place a drop of Loctite #242 (blue) to the bolt threads and mount the shift control plate to the motorcycle frame, Photo 2. FORWARD CONTROL KIT PM SHIFT CONTROL ASSEMBLY Note Before torquing the shift control mounting bolts down, tighten them snug and look behind the shift control mounting plate to where it contacts the mounting lug on the frame. Make sure it fits squarely to the lug before proceeding further. Torque the two shift control mounting bolts down to 25 ft-lb. Using a 3/8″ x 1″ hex head bolt with a lock and flat washer put a drop of Loctite #242 (blue) on the threads and insert the bolt through the rear of the control mounting plate and attach the foot-peg pivot to it. Tighten the bolt while holding the footpeg pivot so that its hinge is lined up in a 45˚ rear facing angle. Thread supplied shift rod coupler to stock shift rod end at trans arm. Mount the shift pedal to the other end of the shift ro d using a 5/16″ x 1″ socket head screw and Nylocnut . Adjust the transmission shift linkage so that the shift arm on the forward controls and the shift arm on the transmission are parallel. Secure it with the jam nuts. Apply a drop of Loctite #242 (blue) to the threads under the jam nut before tightening see Photo 3 After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use. A Shim Washer PHOTO 4 A B C D PHOTO 5 A PHOTO 6 PHOTO 7 Note For complete brake system removal instructions and precau – tions refer to the appropriate service manual for your year and model motorcycle

Incoming search terms:

HARLEY DAVIDSON CHROME/BLACK FRONT MASTER CYLINDER COVER KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Do NOT allow dirt or debris to enter the master cylinder reservoir. Dirt or debris in the reservoir can cause improper operation and equipment damage. (00205b) NOTE If this is a master cylinder cover replacement, start with step 1. If this is new installation for a hydraulic clutch kit, go to step 3. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Clean front master cylinder cover, then remove the two screws that hold the cover in place. 2. Remove the original cover (with sight glass) and gasket. 3. Put new cover and gasket in position. 4. See Service Parts illustration. Install the new cover screws (1) and tighten to 6-8 in-lbs (.7-.9 Nm). Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) NOTE The cover is lab led for D.O.T. 4 brake fluid. Install this cover on reservoirs filled only with D.O.T. 4 brake fluid. Do not mix grades of brake fluid. as they are not compatible and could cause equipment damage.

Yamaha Forward Control Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 17-01-2012

download
After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use

HARLEY DAVIDSON BILLET CLOCK, FRONT BRAKE MASTER CYLINDER MOUNT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION 1. See Figure 1. Clean the face of the front master cylinder reservoir with denatured alcohol and a paper towel. 2. Remove the paper backing from the adhesive strip, and line the clock up squarely to the master cylinder reservoir as shown. Press firmly into place and hold for a few seconds. 3. Let the adhesive set for a while before setting the time. SETTING THE TIME ON THE CLOCK 1. Using the hex key included in the kit, remove the two screws securing the faceplate to the clock housing 2. Lift off the faceplate and “O”-ring, and set aside. Lift the clock face and movement assembly out of the housing. 3. Pull out the stem carefully, and turn it until the hands indicate the correct time. Carefully push the stem back in to start the clock. 4. Check that the “O”-ring is in place in the faceplate, and re-install the faceplate to the clock housing. Do not over- tighten. REPLACING THE CLOCK BATTERY The clock battery (Type SR626SW) is a common type, available wherever watch batteries are sold. When storing the motorcycle for a long period, pull out the stem carefully to stop the clock and save battery life

HONDA 2002-2004 GL1800/A Linked Braking System (LBS) Proportional Control Valve (PCV) Leakage

0

Filed Under (Honda) by admin on 25-11-2010

download
1. Pump the rear brake pedal four times. •If the brake pedal feels spongy, bleed the brake system per the Service Manual. After verifying proper brake system operation, proceed to step 2 below. •If the brake pedal does not feel spongy, proceed to step 2 below. 2. Place the motorcycle on its side stand, with the handlebars in the full left position . Lock the handlebars. 3. Place a scissor jack directly under the left front brake caliper as shown in the illustration. To avoid damage to the caliper, place a protective piece of rubber (such as a piece of inner tube) between the caliper and the jack. Wind up the jack until the front wheel is approximately 15 mm off the ground. 4. Measure the distance from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). Record this measurement . • If the measured length is 30.3 mm, replace the PCV per the Service Manual. (This length indicates the unit’s secondary master cylinder is fully stroked, which means there is no hydraulic brake pressure acting on the PCV.) After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. •If the measured length is longer than 30.3 mm , proceed to step 5 below. • INSPECTION/REPAIR PROCEDURE Record this measurement. Pump the rear brake pedal four times.
GL1800/A #16 ©2005 American Honda Motor Co., Inc. – All Rights Reserved 3 of 6 FEBRUARY 2005 5. Wait 30 minutes. Do not disturb the motorcycle in any way during this time. 6. Measure the distance again from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). •If the measurement has decreased more than 1 mm from the measurement you recorded, proceed to step 7 below. •If the measurement is within 1 mm of the measurement you recorded, the PCV is OK. Proceed to the IDENTIFICATION section of this Service Bulletin. 7. Check the PCV for leakage. • If the PCV is leaking , replace the PCV per the Service Manual. After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. • If the PCV is not leaking , you must diagnose the brake system problem before proceeding. After you have diagnosed and repaired the brake system, proceed to the IDENTIFICATION section of this Service Bulletin. NOTE: Any brake system problem not related to the PCV that is found while performing this Service Bulletin is not covered by this Safety Recall. If the motorcycle’s original factory warranty is still in effect or under HPP, file a normal warranty claim. If the unit is outside its factory warranty period or HPP coverage, contact TechLine for goodwill consideration. 8. Verify proper front and rear brake operation by pumping the front brake lever and rear brake pedal before riding the motorcycle

Incoming search terms:

Harley-Davidson CHROME/ BLACK FRONT MASTER CYLINDER COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-10-2010

download
if this is a master cylinder cover replacement, start with step 1. If this is new installation for a hydraulic clutch kit, go to step 3. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Clean front master cylinder cover, then remove the two screws that hold the cover in place. 2. Remove the original cover (with sight glass) and gasket. 3. Put new cover and gasket in position. 4. See Service Parts illustration. Install the new cover screws (1) and tighten to 6-8 in-lbs (.7-.9 Nm). Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) NOTE The cover is lab led for D.O.T. 4 brake fluid. Install this cover on reservoirs filled only with D.O.T. 4 brake fluid. Do not mix grades of brake fluid. as they are not compatible and could cause equipment damage. SERVICE PARTS See Figure 1 and Table 1

HARLEY DAVIDSON CHROME REAR MASTER CYLINDER COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
1. Clean rear master cylinder cover, then remove two screws that hold cover in place. 2. Remove original cover (with sight glass) and gasket. 3. Put new cover and gasket in position. 4. Install cover screws and tighten screws (1) to 6-8 in-lbs (.7-.9 Nm). Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a

Ducati Sport Clutch Lever INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 26-10-2010

download
1 To remove your stock lever, use a 19mm wrench or (adjustable wrench) to remove the large sheet metal nut attached to the main pivot bolt that holds the lever. (Photo 1a) Once the locknut is removed, push the main pivot bolt out with your finger or if necessary tap lightly with a rubber mallet or plastic handle end of a screwdriver (Photo 1b) After the pivot bolt is removed, the lever will detach from the master cylinder. (Photo 1c) 1a See other side for further instructions INSTALLATION INSTRUCTIONS FOR PART # CRC552 ® C/5 Sport Clutch Lever Part # CRC552 1b 1c INSTRUCTIONS_CRC552 12/27/07 10:05 AM 23 4 2 Included with your ASV lever is a plastic bag that contains a custom pivot bolt, spacer & locknut. These parts will replace the OEM Brembo parts that were used with your stock lever. 3 Carefully place the lever into the master cylinder while aligning the plunger rod into the plunger cup on your ASV lever as shown in photo 3. 4 Align the lever and the master cylinder pivot bolt holes and Install the main pivot bolt, you will need to pre-load the lever into the master cylinder to get the bolt through the holes. The bolt head has two cut outs on the sides that need to be aligned with the matching area on the master cylinder. Be sure the head of the bolt seats down into the slotted area of the master cylinder. It may be necessary to use a rubber mallet or Plastic end of a screwdriver (Photo 4) to tap the head of the bolt down into its slot. 5 On the other side of the pivot bolt where the threads are, you will see that there is space around the pivot bolt. You will need to install the aluminum spacer that was supplied in the plastic bag with the pivot bolt and locknut. The spacer has a small flange on one side. The flange should be on the outer side when installing it into the hole surrounding the bolt. (Photo 5a) You may need to use pressure to seat the spacer fully into the hole surrounding the pivot bolt. You should be able to do this by using your fingers or thumbs as shown in photo 5b.

Incoming search terms:

Incoming search terms: