doese my 1999 electra glideultra classic have a speedo cable or sensor

You search Auto repair manual PDF doese my 1999 electra glideultra classic have a speedo cable or sensor, if there are search results will appear below. If search results do not exist, please search by others keyword.



  doese my 1999 electra glideultra classic have a speedo cable or sensor Direct Download speed 5282 Kb/s

  doese my 1999 electra glideultra classic have a speedo cable or sensor Full Version speed 6162 Kb/s



HARLEY DAVIDSON DIAMONDBACK "LE" CHROME SERIES CLUTCH CABLE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

Harley-Davidson Softail, Touring, Dyna, Sportster and V-Rod, SELF LEARNING MODULE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2012

download
STEP 1 – BATTERY CONNECTION Locate the battery and disconnect the negative battery cable. Mount the module in the open area in front of the battery with 2-tie straps or velcro straps, directing the harness from the module towards the 6 o’clock position. STEP 2 – THROTTLE POSITION SENSOR (TPS): Remove the air cleaner assembly and unplug the TPS sensor connector at the TPS sensor. The harness includes (2) TPS connectors which should be routed under the gas tank into the factory wire loom to the TPS sensor. The TPS sensor is located on the left side of the throttle body. Plug the (2) TPS connectors from the module in between the TPS sensor and to the factory TPS connector. STEP 3 – O2 SENSOR: Systems equipped with factory O2 sensors Rear: Unplug the Rear O2 sensor connector from the factory harness, which is located at the Rear exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors and connect one connector to the Rear O2 sensor and connect the other connector to the main factory O2 sensor connector. Front: Unplug the Front O2 sensor connector from the factory harness, which is located at the Front exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors, and connect one connector to the Front O2 sensor and connect the other connector to the main factory O2 sensor connector. Systems not equipped with factory O2 sensors NOTE: Many aftermarket exhaust systems are now equipped with plugged O2 sensor bungs which can be removed to accept an aftermarket O2 sensor. Typically these bungs already have a thread size of 18 mm x 1.5 mm. Exhaust systems not equipped with O2 sensor bungs need to have the supplied 18 mm x 1.5 mm thread size bung welded to the exhaust pipe in order to install an O2 sensor. The O2 sensor bung should be installed 3 to 6 inches away from the rear cylinder exhaust port and in front of the exhaust torque tube pipe area. The module prefers to receive information from the O2 sensor from an area that is NOT contaminated from atmospheric air. This air may enter through the tail pipe of an unrestricted or un-baffled exhaust pipe. The bung should not be installed in the “5 to 7 o’clock” area. If mounted in this area the O2 sensor can be damaged. The moisture from the gases exiting from the rear cylinder exhaust port will harm the ceramic shell element of the O2 sensor.

Incoming search terms:

HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be installed in the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3 2 1 is00825 1. Brake lever 2.5/32 inch (4 mm) cardboard insert 3. Brake lever bracket Figure 1. Install Cardboard Insert 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 3 4 1 2 5 is 02071 1. Upper switch housing 2. Lower switch housing 3. Throttle cable adjuster 4. Idle cable adjuster 5. Adjuster jam nut Figure 2. Handlebar Throttle Control 4. Remove the right upper and lower switch housing screws. 5. Loosen the upper screw securing the handlebar clamp to the master cylinder housing. Remove the lower clamp screw and flat washer. NOTE If possible, leave the friction shoe in place. The friction shoe is a loose-fit and may fall out or become dislodged if the lower switch housing is turned upside down or shaken. 6. See Figure 3. Remove the brass ferrules from the notches on the inboard side of the throttle control grip. Remove the ferrules from the cable end fittings. 1 2 4 3 is 02072 1. Throttle cable 2. Idle cable 3. Brass ferrule 4. Notch Figure 3. Throttle/Idle Control Cables 7. Pull the crimped inserts at the end of the throttle and idle control cable housings from the lower switch housing. For best results, use a rocking motion while pulling. Remove cables with retaining rings from switch housing. Apply a drop of light oil on the retaining ring, if necessary, to help in removal. NOTE If installing different handlebars, measure the change in distance that will be required from the end of the cable housing to the throttle grip. Compare this additional required length to the cables provided in the kit. If the cables are more than 2.0 inches (51 mm) longer or more than 1.0 inch (25 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. Install proper length throttle cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00396b) 8. Follow instructions in the applicable service manual and remove air cleaner and backplate.

Incoming search terms:

HARLEY DAVIDSON DETACHABLE TOUR-PAK KIT FOR ELECTRA GLIDE CLASSIC INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Install Docking Kits and License Plate Holder 1. Install Rear Detachable Docking kit. Refer to the instruction sheet provided with kit. 2. Install Touring Detachable Tour-Pak Rack. Refer to the instruction sheet provided with kit. 1 4 2 3 is03989 1. License Plate Holder 2. Red Reflector 3. Original Equipment Screws 4. Original Equipment Bottom Support Tube Figure 2. Install License Plate Holder 3. See Figure 2. Install the new license plate holder (1) to the bottom support tube (4) using screws (3) saved from prior step. 4. Remove adhesive backing from red reflector (2) and carefully center and align it with the bottom edge of the license plate holder (1) and press firmly into place. -J03930 1 of 4 MOUNTING ANTENNA RELOCATION BRACKET 1. See Figure 6. Assemble joint assembly (9) to antenna mounting bracket (6) using lock washer (5) and 2 hex nuts (4). Tighten hardware securely. 2 1 5 4 3 is03992 1. Rear Docking Point 2. Docking Point Support Bracket 3. Antenna Mounting Bracket 4. Antenna/Cable Adapter 5. Rear Docking Point Screw and Locknut Figure 3. Relocated Antenna Bracket and Cable 2. See Figure 3. Install assembled antenna bracket (3) by removing screw and locknut (5) securing left rear docking point (1) to docking support (2). Install bracket as shown and reinstall rear docking point screw and locknut. Tighten screw and locknut to 15-19 ft-lbs (20.3-25.7 Nm) . 3. Thread antenna/cable adapter (4) onto joint assembly. ROUTING ANTENNA CABLES 1. See Figure 4. Gently remove left side cover (1) by pulling from frame tubes (no tools required). 2. Connect original antenna cable (not shown) to bottom of joint assembly. 3. Route antenna cable/wiring between left frame rail and fender. 4. See Figure 5. Attach cable to docking point support bracket in location (1) using short cable strap. 5. See Figure 4. Coil excess antenna cable/wiring (2) and use long cable strap (3) to fasten cable to frame under left side cover (1) with vehicle wiring harness. 6. See Figure 6. Cap unused wiring connector with connector housing (10).

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

HARLEY DAVIDSON ELECTRA-GLO LIGHT POD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTES Clean the controller mounting area and the areas where the light pods will be mounted with soap and water before beginning the installation, and allow to dry thoroughly. Remove debris, dirt and grime from the vehicle areas to be highlighted. Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the light pods and controller box to vehicle surfaces. Light pods should not be located closer than 2.5 inches (63.5 mm) from exhaust pipes or mufflers, and must have 1.5 inches (38.1 mm) clearance from engine cylinders and heads. Do not install light pods with the light source facing directly away from the vehicle. Installation should be done in a way that allows the light to be seen indirectly by reflecting from chrome or painted surfaces of the vehicle. Prepare the Motorcycle To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to disconnect the battery cables, negative (-) cable first. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Locate and Install the Controller NOTE Do not mount the controller box in a location where vehicle suspension travel could result in contact with the ON/OFF switch or dimmer control. Damage to the controller box will occur. 2. See Figure 2. Locate the controller box (10) on a flat surface that will allow the red (+) and black (-) leads to reach the battery terminals and the rider to access the controls (with the vehicle parked) and, if necessary, the in-line fuse holder (A). a. Test-fit the controller box to the selected surface before installation. Do not remove the adhesive backing until ready to attach the controller box. b. Clean the controller box mounting area with one of the included alcohol swabs. Allow to dry thoroughly. c. Remove the liner from the adhesive backing of the controller box. Carefully position the controller box to the surface, and press firmly into place. Hold the controller box in position with steady pressure for about one minute. Connect the Battery Cables NOTE Verify that the ignition/light key switch is in the OFF position before attaching the battery cables. 3. Verify that the ignition/key switch is turned to the OFF position. Apply a light coat of Harley-Davidson electrical contact lubricant (part number 99861-02), petroleum jelly or corrosion retardant material to the battery terminals. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Refer to the owner’s manual and follow the instructions given to install first the vehicle’s positive (+) battery cable then the red (+) light pod controller lead ring terminal to the positive (+) battery terminal. Tighten to owner’s manual specifications. Install first the vehicle’s negative (-) battery cable then the black (-) light pod controller lead ring terminal to the negative (-) battery terminal. Tighten to owner’s manual specifications. Arrange the Electra-Glo Light Pods NOTES Electra-Glo light pods (1) can be installed in a variety of locations. They are best installed on a flat surface to provide indirect lighting illuminating mechanical features, vehicle finish or for ground effects. Refer to the notes at the beginning of the Installation section. 5. Select the area or lines of the motorcycle to highlight, and suitable locations for each light pod. DO NOT permanently affix the light pods at this time. Lightly tape the pods in place temporarily until the desired visual effect is achieved Verify clearance from movement of rubber mounted engine or other moving parts, heat sources, or chafe points

Incoming search terms:

Incoming search terms: