drilling holes in bagger

You search Auto repair manual PDF drilling holes in bagger, if there are search results will appear below. If search results do not exist, please search by others keyword.



  drilling holes in bagger Direct Download speed 5282 Kb/s

  drilling holes in bagger Full Version speed 6162 Kb/s



HARLEY DAVIDSON TOUR-PAK KIT INTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the rubber mat from the bottom of the Tour-Pak. 2. See Figure 1 and Table 1 to determine the proper hole configuration to attach the Tour-Pak to your luggage rack. Holes will be drilled as explained in Step 3 in the hole location for your luggage rack. Table 1. Luggage Rack and Hole Configurations Hole Configura- tion Luggage Rack C (3 holes) Stock 1997 B (4 holes) Detachable luggage rack 53107-96 A (5 holes) Luggage rack 53118-97A and luggage rack 53118-98 A (5 holes) Stock 1998 and later racks A (5 holes) Detachable Tour-Pak rack 53276-04 B (4 holes) Solo detachable Tour-Pak rack 53655-04 B (4 holes) Detachable Tour-Pak rack 53066-00B B (4 holes) Solo detachable Tour-Pak rack 53559-04A A (5 holes) Solo detachable Tour-Pak rack 53260-02 -J03631 1 of 3 B 1 A C 2 2 2 is00163 1. Front of motorcycle 2. Bottom view of Tour-Pak interior (rubber mat removed) Figure 1. Hole configurations for Tour-Pak attachment NOTE Drilling holes in Tour-Pak without wood underneath each hole site may result in the leather becoming damaged during the drilling process. 3. Place blocks of wood underneath the Tour-Pak where the holes will be drilled to prevent damage to the leather while drilling. Use the pre-drilled holes in the metal base as a guide and carefully drill the holes through the leather in the proper location using a 11/32 inch drill bit. 4. See Figure 2. For detachable luggage racks (53107- 96, 53066-00B and 53276-04): Install black cover tube to the front bar (1) of the luggage rack, as shown. This tube is used to provide a cleaner look. The black cover tube is not for use with other luggage racks. 5. Attach Tour-Pak to rack using the mounting screws provided in the Luggage Rack kit. Put bolt through from inside of Tour-Pak. Tighten screws to specifications found in the Luggage Rack kit. 6. Place the black rubber mat on the bottom of the Tour-Pak. 7. If luggage rack was removed, reattach to motorcycle according to kit instructions or Service Manual instructions

Incoming search terms:

HARLEY DAVIDSON FLSTS MUD FLAP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
Installation For installation on rear fender with marker light: 1. Cut out Rear Fender Template. 2. Use a paper punch to punch out holes marked A and C . Holes A are the locations of the marker light screws, and hole C is the location of the marker light wiring. Cut along centerline of template from top down to hole C . 3. Remove light lens by carefully pressing down on top center of light to disengage tab. 4. Remove the two screws, washers, and nuts that hold the marker light assembly in place and carefully pull the light assembly away from the fender. Disconnect the wire connector and remove the light assembly. 5. Slip template over marker light wires, align holes marked A with marker light holes, and align lower edge of template with lower edge of fender. Tape template in place. 6. Prick punch holes marked B at indicated centers on template. 7. Carefully, and as accurately as possible, drill holes marked B in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 8. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure outer holes with buttonhead screws (3), washers (6), and locknuts (7) contained in kit. The mud flap is split to fit around light assembly wires. 9. Using the longer panhead screws provided in the kit, install fender tip light and check that light is operational. For installation on rear fender without marker light: 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Rear Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes marked B and C at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked B and C in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit. For installation on front fender (FLSTS only): 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Front Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit

Incoming search terms:

HARLEY DAVIDSON VRSCF LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
REMOVAL 1. See Figure 1. Remove four rear fender mounting bolts (1) and washers (2). If necessary, move the ECM to access the four fender mounting bolts. 2. Disconnect the tail lamp following the instructions in the appropriate service manual. 1 2 is05463 1. Bolt (4) 2. Washer (4) Figure 1. Fender Mounting Bolts INSTALLATION NOTE There are bosses molded into the inside of the fender to use as the hole drilling templates. 1. See Figure 2. Apply masking tape to the outside painted surface of the fender at the three hole locations (1 and 2). This will protect the painted surface during the drilling operation. 2. Put the fender on a work bench, painted surface down. Use clean, soft cloth between the fender and the work bench to protect the paint finish. NOTES Drilling each hole in the fender is a two-step procedure that requires a specific type of drill bit to avoid damaging the fender. 3. See Figure 2. Use a 1/2-inch spade bit or 1/2-inch unibit (do not use a spiral-type drill bit) to drill three holes from the inside of the fender through the three pilot hole bosses (1 and 2). Stop drilling when the tip of the bit just pierces the outside surface of the fender. 4. Turn the fender over so the painted surface is now facing up. Complete each hole by using the same 1/2-inch drill bit at each of the pierced holes. Clean excess material from the holes and clean the fender surface of any debris. 5. See Figure 5. Remove the masking tape from the holes and apply the protective tape (3) to the painted surface using the drilled holes for alignment. 6. See Figure 3. Put the luggage rack (1) upside down on the work bench and align the holes in the luggage rack with the holes in the fender (2).

HARLEY DAVIDSON SOFTAIL DETACHABLE TWO-UP TOUR-PAK LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download

TOUR-PAK LUGGAGE INSTALLATION TO RACK 1. Open the lid and, if necessary, remove all items from inside the Tour-Pak luggage.  Remove the rubber mat from the luggage floor. 2. If holes ARE NOT pre-drilled in the floor of the luggage,       see Figure 1. To prevent damage to the leather while drilling, place blocks of wood underneath the Tour-Pak luggage at the drilling sites.  Use the four inboard holes (3) in the metal base of the luggage (2) as a guide, and carefully drill four 11/32 inch (9 mm)  holes through the floor of the luggage. 1 2 3 is04249 1. Front of motorcycle 2. Tour-Pak 3. Drill four 11/32 inch (9 mm) diameter holes Figure 1.  Drill Attachment Hole Locations in Tour-Pak NOTE See Figure 3. When installing the luggage to the rack in the following steps, note that holes in the luggage rack (2) provide forward (A) and rearward (B) positions for mounting the lug- gage. 3. Place the luggage on the luggage rack.  Align the holes in the luggage mounting plate with the forward or rearward holes in the rack. 4. ALL applications: Obtain the hex head cap screws (9), lock nuts (11) and plain washers (10) from the kit. Place a washer over the threads of each screw, and insert the screw threads, from the inside, through the Tour-Pak luggage mounting plate and floor, and into the holes in the rack. NOTE Always install the mounting screws from inside the luggage.  If the screws are installed from the bottom, the screw ends can tear the rubber mat and scratch objects, such as helmets, stored inside the luggage. 5. From the underside of the rack, install a washer and lock nut onto the threads of each screw.  In a crosswise pattern, incrementally tighten each screw to 19 ft-lbs (25 Nm) . 6. Install the rubber mat into the luggage.  Close and latch the lid. 7. If not already in place, install the Detachable Docking Hardware Kit to the vehicle per the instructions in that kit

Incoming search terms:

HARLEY DAVIDSON CHROME SADDLEBAG LID TRIM KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION 1. Remove all articles from inside, then thoroughly wash and dry the saddlebag lid. 2. Close the saddlebag lid. Cut a piece of masking tape at least 10 inches (25 cm) long and lay it lengthwise down the center of the top outer surface of the lid starting at the front. Mark a line lengthwise down the tape, measuring an equal distance from each side so the line is centered on the lid. 3. Obtain the template (7) from the kit, and position it on the line, with the short leg held against the front surface of the lid. Carefully mark the tape at the two arrows, then remove the template and set it aside. 4. At each of the marks made in Step 3, carefully drill a 1/8 inch (3 mm) diameter pilot hole. 5. Using the pilot holes drilled in Step 4, use a 9/32 inch (7 mm) diameter bit to finish drilling the holes for the trim piece. NOTES Before installing the lid trim, test fit to ensure adequate clearance of both mounting pads through the drilled holes in the saddlebag lid. The trim pieces are side-specific; the front legs are angled to match the lid front. If the pads do not fit loosely in the holes, it may be necessary to slightly enlarge the holes to provide clearance and maintain proper alignment of the trim on the lid. Clean the saddlebag lid inside and out, and the inside of the saddlebag with a soft cloth, making sure to remove any shavings left from drilling. 6. Obtain the correct saddlebag lid trim (1 or 2) and a trim gasket (3) from the kit. Peel the liner from the adhesive backing of the gasket. 7. Position the gasket onto the bottom surface of the trim, making sure the gasket remains inside the outer edges of the trim, and smooth it into place. 8. Obtain a pan head screw (6) from the kit. 9. Using a T25 TORX® drive head, start the screw part way into one of the holes on the underside of the trim, to form a few threads in the hole, then back the screw out of the hole. Repeat for the second hole. 10. Install the trim piece onto the lid, fitting the mounting pads into the holes drilled in Step 5. 11. Place a flat washer (5) from the kit onto the threads of the screw (6), followed by a rubber washer (4). Place two drops of Loctite® 243 (blue) onto the screw threads. 12. While supporting the lid trim in place, open the saddlebag lid and install the washers and screw through the lid into one of the trim mounting pads, finger tight. Repeat for the remaining trim mounting pad, with another screw, flat washer and rubber washer. 13. Apply a small amount of pressure to the trim piece above each screw and continue to tighten both screws to 25-28 in-lbs (2.8-3.2 Nm) . 14. Repeat steps 1 through 13 for the opposite saddlebag lid

Incoming search terms:

Harley- Davidson Bagger Audio factory service manual for removal

0

Filed Under (Harley Davidson) by admin on 03-04-2012

download
POWER & SPEAKER HARNESS INSTALLATION- (Read electrical connections prior to connecting center power and ground wires) 1. Disconnect battery (negative cable first!) 2. Remove outer faring cover 3. Route long speaker wires from fairing area through tank channel to seat area. 4. Route one pair of speaker wires under each fender strut support; purple and purple and black wires to the right and green and green and black wires to the left. AMPLIFIER INSTALLATION- 1. Factory installed electronics will determine suggested placement of amplifier. 2. Position and attach amplifier to outer fairing support bars with supplied wire ties. (Electra/Ultra/Street Glide) BAGGER AUDIO™ LIDS INSTALLATION- Detach factory lid by removing the 2 screws holding the factory strap to inner lid and 5 small torque screws holding lid to factory latch assembly. (Consult factory service manual for further instructions) Remove metal strap from behind factory seal (This is the metal strap that the previous 5 small torque screws were removed from) Position metal strap in same location on your new lid. (If you purchased your product unpainted, you must install the supplied seal to your finished lid) Reattach BAGGER AUDIO™ LIDS by installing the 5 small torque screws in the same location as on the factory lid. (We suggest that you have an assistant hold the lid in place while attaching your new lids) Replace factory nylon Hinge straps with new nylon straps supplied in kit. Use metal straps and machined screws to secure the nylon hinge straps. 
 Place a small bead of silicone on the inside rim of the speaker basket to create a watertight seal between the inside of the lid and the speaker. 
 Install speaker into the bottom of the lid (not through the top opening) with supplied stainless screws and washers (4 per lid). Be sure to center speaker in lid opening to ensure proper speaker grill placement. Install speaker with terminals facing toward the front of the lid. One 1/4″ hole must be drilled in each bag. Holes can be positioned at the ownerʼs discretion. Place rubber grommet in drilled hole before running wires

PASSENGER FLOORBOARD RELOCATION ARMS FOR TRIUMPH AMERICA AND SPEEDMASTER

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. If you are installing the relocation arms at the same time as floorboards install the floorboards first per their instructions. When installing the relocation arms with floorboards already installed proceed as follows. 2. Starting on the left side, fold the floorboard up. Remove the socket head bolt and nut which secures the floorboard to the motorcycles stock peg support and remove the floorboard taking notice of which holes the dowel pins are located in. 3. Install one of the 5/16″x1 Ω” hex bolts supplied thru the stock peg support from the backside (The threads of the bolt will face out towards you.) Place the two dowel pins into the holes at one o’clock and seven o’clock on the stock peg mount. Place the spacer blocks backside (stamped with an “L”) onto the bolt and align the hole with the pins. 4. Locate the relocation arm that has an “L” stamped on the backside of it. Place two of the supplied dowel pins into one of the two sets of the holes in the arm that are directly across from one another (180 degrees apart). Place the arm onto the spacer bock aligning the pins in the arm with the holes closest to six and twelve o’clock. Depending on which of the two sets of holes on the arm you chose the arm would, either be down at about seven o’clock or just below nine o’clock. These are the initial height settings and you may select which ever set is most comfortable for the passenger. Install one of the acorn nuts supplied onto the bolt and make finger tight. 5. Place the floorboard with its two dowel pins into the set of holes at the other end of the relocation arm that allows the floorboard to be horizontal or parallel to the ground. Use one of the 5/16″x3/4″ socket head bolts supplied to bolt the floorboard to the relocation arm and make finger tight. 6. Install the right side in the same manner, place the dowel pins in the holes at eleven o’clock and at five o’clock on the stock peg mount, then the spacer blocks backside (stamped “R”) onto the pins followed by the relocation arm with two dowel pins in one set of holes (180 degrees apart). Check to see that the right arm is at the same height or position as the left then install the acorn nut finger tight. Bolt the floorboard the other end of the arm using the remaining dowel pins and socket head bolt. Tighten the two bolts with the acorn nuts and the two socket head bolts securely

YAMAHA ROADLINER AND STRATOLINER PASSENGER FLOOBOARD RELOCATION ARMS

0

Filed Under (Yamaha) by admin on 23-12-2010

download
1. When installing floorboards at the same time first refer to their instructions and using the longer right side black floorboards mounting block supplied with this set of relocation arms. Leave the final floorboards mounting bolt installed loosely at this time. 2. If installing the relocation arms after installing the floorboards at an earlier date proceed as follows. 3. On the left side remove the Allen screw below the floorboards pivot and remove the floorboard from the black mounting block. Remove the dowel pins from their holes on the block. Locate the left relocation arm (stamped “L” and “R” on their backsides). On the end with the clearance hole (not threaded) Place the two dowel pins into one of the two sets of holes which are directly across from each other (180 degrees apart). Hold the arm with the dowel pins up to the mounting block. Align the dowel pins with each of the three sets of holes in the block one at a time noting the height of the opposite end of the arm where the floorboard will mount. Move the dowel pins to the other set of holes on the arm and again hold the arm with the dowel pins up to the blocks three sets of holes. Choose the set of holes in both the block and arm which will set the floorboard to the desired height and place the arm with the dowel pins onto the block. Using one of the button head Allen screws supplied bolt the arm to the block and tighten securely. 4. Locate two of the dowel pins supplied and one of the Allen screw removed earlier. Place the dowel pins into the holes of the arm which allow the floorboard to be level or parallel to the ground. Place a drop of loctite on the threads of the screw and tighten securely. Install the right floorboard in the same manner. 5. On the right side remove the floorboard from the mounting block. Remove the mounting block and replace it with the longer one supplied. Install the right arm in the same manner as the left using the set of dowel pin holes to match the height or angle of the left arm. Install the right floorboard and tighten securely. Recheck all fasteners for tightness.

HARLEY DAVIDSON FRONT FENDER RAILS AND STANCHIONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
INSTALLATION 1. Carefully cut out appropriate template from sheet included in kit. One side is for FLSTS style fenders (with elliptical hole for front fender lamp), and the other side is for FLT style fenders (with rectangular front fender lamp). 2. Lay template on front fender (align around front fender lamp). 3. Underneath four holes marked on template, place high quality masking tape on fender. 4. Using a tape measure, measure from the top of the striping on the sides of each side of the fender, to the centerline of the each of the holes on the template (on some FLT models, with chrome fender trim, measure from the chrome fender trim at the bottom edge of the fender). Make sure that the distances are equal so that the template is centered on the fender. 5. Tape the template to the fender using high quality masking tape. NOTE Before proceeding, stand directly in front of the fender and carefully check to make sure the template is centered on the fender. 6. Center punch the center point of each of the four holes. 7. Remove the template from the fender. 8. Block motorcycle under frame so the front wheel is raised off the ground. 9. Follow appropriate Service Manual procedures and remove the front axle. 10. Place a rag on the top of the front brake caliper, then lower the front wheel so that it is resting on top of the brake caliper. NOTE When drilling fender holes, use care not to hit tire with drill bit. 11. While holding the fender firmly, and using caution to make sure that your drill bit does not hit the tire, drill the four holes at the points marked by the center punch. Begin with a 1/8 inch drill bit, followed by a 9/32 inch, and finally a 3/8 inch drill bit. 12. Remove the masking tape and any burrs that may have formed. 13. Remove the adhesive backing from each of the foam pads on the bottom of each of the stanchions. 14. Place the studs from each of the end stanchions into the holes (you may need to rotate the rails 180 degrees if they appear to be bowed out). 15. Reaching from the front of the fender, place kit washer, and then a locknut, over each of the studs on the underside of the fender. 16. Securely tighten each locknut so that the stanchion is firmly clamped to the fender. 17. Follow appropriate Service Manual procedures and replace the front wheel and axle

BMW R1150R Roadster CargoRest FitKit Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
Check to determine if the BMW system case mounts have been properly installed and that all fasteners and fittings are properly tightened. Inspect for signs of stress, fracture, bending, or other failure. If found, return the mounts to your dealer for replacement. Do not attempt to mount the BestRest FitKit if the BMW system case saddlebag mounts are damaged, defective, or improperly installed. If the BMW luggage rack is in place, remove it from the system case mounts. Removal is accomplished by removing the 4 torx screws, 2 on each side. Use the torx wrench from your toolkit. Once the stock “luggage” rack is removed, you’ll be mounting the Roadster FitKit using those same 4 holes. You’ll be replacing the stock torx head screws with the longer socket head hex screws found in the parts package. Place a flat washer on the 6mm screws and start the screws into the 4 holes. The 4 screws may need some gentle help to get them thru the holes. Work patiently and do not use brute force! Once the screws have started in the holes, turn them clockwise with a hex wrench to help them pass thru the saddlebag mounts and the FitKit Plate. Place a flat washer and 6mm nylon locknut on the end of each screw and tighten the nuts <<<<>>>>. From the rear, lift up on the FitKit Plate and “wiggle” it up and down <<<>>> a few times to remove any tension between the FitKit Plate and the system case brackets. You’ll find a point where everything feels “neutral” and where the screws are aligned in their holes. Tighten the nuts fully. Use common sense and do not over-tighten. Do not use extensions on the hex wrench. As a final tightening technique, hold the hex wrench stationary while you tighten the nuts another ¼ turn, using the box wrench. From the rear, wiggle the FitKit Plate up and down again. If it’s loose, tighten the screws and nuts again. Repeat until the FitKit Plate is snug and secure between the bag mounts. Place a CargoRest over the top of the FitKit Plate. Installation is the same for all 3 models of CargoRest. Align the 5 holes shown in the photo with the holes in the FitKit Plate.

Incoming search terms: