drive belt for heritage softail with lehman trike kit

You search Auto repair manual PDF drive belt for heritage softail with lehman trike kit, if there are search results will appear below. If search results do not exist, please search by others keyword.



  drive belt for heritage softail with lehman trike kit Direct Download speed 5282 Kb/s

  drive belt for heritage softail with lehman trike kit Full Version speed 6162 Kb/s



HARLEY DAVIDSON SECONDARY BELT EMERGENCY KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
The 40101-80 kit, with a 126 tooth belt, fits: •1980-1986 FXB and 1984-1986 FXWG models This kit may also be used on 1989-1992 international Softail models with a 127 tooth belt. The 40171-97 kit, with a 130 tooth belt, fits: •1995 and later domestic Softail models •1994 and later international Softail models •1994 and later international Dyna models The 40109-86 kit, with a 132 tooth belt, fits •1986-1992 and 1994 domestic Softail models •1989-1993 international FLT and FXR models This kit may also be used on the following models with 133 tooth belts: •1991 and later domestic Dyna models •1991-1992 international Dyna models •1994-1995 international FLT models The 40100-85 kit, with a 136 tooth belt, fits: •1985-1994 domestic FXR models •1985-1996 domestic FLT models •1996 international FLT models The 40112-97 kit, with a 139 tooth belt fits •1997 FLT models Installation 1. Put transmission in ‘Neutral’. 2. Loosen rear axle nut. Loosen rear axle adjuster nut on each side of motorcycle, and move rear wheel to full forward position. 3. Remove the damaged/broken belt. 4. Inspect sprockets and belt guard for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 5. See Figure 1. Remove belt guard. 6. See Figure 2. Install feeder strip on emergency belt. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support.

Harley-Davidson EMERGENCY DRIVE BELT REPLACEMENT KIT Installation Manual

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Shift transmission to neutral. Before installation of the emergency belt, to avoid personal injury and/or vehicle damage, secure the motorcycle. Both stand and motorcycle must be on solid, level ground. Failure to follow instructions could result in death or serious injury. 2. See Figure 1. Remove spring clip (4) (if present) and loosen rear axle nut (1). 3. Loosen rear axle adjuster (3) (or adjuster nut, if so equipped) on each side of motorcycle, and move rear wheel to full forward position. 4. Remove the damaged/broken belt. 5. Inspect sprockets and belt guard (2) for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 6. Remove belt guard. 40171-97,40146-00 1 WARNING i06186 Figure 1. Axle 1. Axle nut 2. Belt guard 3. Adjuster 4. Spring clip 2 4 1 3 7. See Figure 2. Install feeder strip on emergency belt. 8. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support. 9. See Figure 3. Interlock the “v” ends of the emergency belt. a. Insert a hex socket key in the fourth (4) and ninth (6) tooth holes. b. Place the splice block (2) over the seventh (5) tooth hole. c. Install a socket head set screw (3) in the seventh tooth. Tighten using another hex socket key. d. Move the block to the next tooth, and repeat installation steps (b) and (c) in each tooth until all 12 screws are installed. NOTE There are 16 screws included in this kit. However, only 12 screws will actually be installed in the belt. The remaining four screws are spares. 10. See Figure 4. Grasp the emergency belt at the mid point of the lower run between your thumb and forefinger and lift the belt up to take up any slack in the belt. Measure the distance that the belt deflects (2) under tension (1). When two pounds of tension is applied to the lower run of the emergency belt, the belt deflection should be within the following measurements

Incoming search terms:

Yamaha Road Star TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Yamaha) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” about 1/2 to 5/8 inches when pressed with a force of 10 pounds. Do not use commercial belt dressing compounds on the belt: these compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. The suspension system retains your single OEM shock and adds two coil-over “helper” mechanical shocks. The system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight). There is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride

HARLEY DAVIDSON SOFTAIL CHROME LOWER BELT GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
REMOVING STOCK PLASTIC LOWER BELT GUARD 1. See Figure 1. Remove the hex head bolt (2), washer (3), acorn nut (5), hex head screw (4) and acorn bolt (8) attaching plastic belt guard to rear fork. 2. Remove the plastic belt guard. Save fasteners (2), and (4), washer (3), acorn nut (5) and acorn bolt (8) for installing new chrome belt guard. INSTALLING CHROME LOWER BELT GUARD 1. See Figure 2. Position the new chrome belt guard from kit over belt. Align the holes in guard with mounting lugs on rear fork. Install acorn bolt (9) through mounting lug and fasten to belt guard. Finger tighten only. 2. Install screw (4) with washer (5, from kit) through belt guard and fasten to threaded mounting lug. Position the guard for adequate clearance and finger tighten screw. 3. At the upper belt guard, install the original forward hex bolt (2) and original washer (3) through the upper guard (1), then through the upper hole in chrome belt guard and through mounting lug on rear fork. Secure with original acorn nut. 4. Tighten all hardware to 110 in-lbs (12.4 Nm)

1987 to Current Harley Davidson Softail (FLST Only) Motorcycle Trike Conversion removal and Installation Guide

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Seat (to be re-installed without modification). • Left and right saddle bags (if so equipped). • Left and right rear crash bars, saddlebag rails (if so equipped). • Left and right passenger foot rests (to be re-installed without modification) • Complete exhaust system (to be replaced with new system). • Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake caliper is removed • Remove Rear Caliper (disconnect brake line at caliper) NOTE: Cap line to prevent introduction of dust / debris into line. Remove caliper. • Rear Drive Pulley (1987-99 models to be re-installed without modification). • Rear Fender (2000 and newer models, fender mount plates to be reused). • Swing Arm NSTALLING TRIKE CONVERSION KIT 3.1 Sprockets and Drive Belts Specifications See following table for belt installation (1987-99 will use a 4 tooth longer belt) Note : See OEM manual for belt replacement procedure. Year Drive Sprocket OEM Belt New Belt / Sprocket 1987-92 70 T 132 T 136 1993-94 61 T 128 T 132 1995-99 65 T 130 T 136/70TOEM 2000-06 Champion Sprocket, 70 T 135 T Use OEM 2007 Up Champion Sprocket, 66 T Use OEM 3.2 Install Swing Arm É Noting size and location of bolts, remove Cross Assembly from Champion Swing Arm. Do not discard hardware. Figure 1 3.2.1 1987-99 Model Years • Remove bearings from OEM Swing Arm using OEM shop tools and hydraulic press. Note : Although original bearings can be re-used, it is HIGHLY recommended that NEW bearings be installed to Champion Swing Arm a. b. Press bearings into Champion Swing Arm in the same way as the OEM Swing Arm. Using OEM Spacer Tube and supplied washers (four ¾” flat washers), install Champion Swing Arm using OEM bolt, outside washers and nut. Do not torque pivot bolt nut at this time. Figure 2 Note : Insure belt path is over and under Swing Arm pivot. c. d. Replace cross assembly and hardware (previously removed in step 3.2) to Champion Swing Arm. Note that the 2 upper left hand side bolts are countersunk. Torque pivot bolt to OEM specification

BMW R850, R1100, R1150, R1200 Oilhead Maintenance Manual

0

Filed Under (BMW) by admin on 16-11-2010

download
cold Engine and Drivetrain Procedures Check Alternator Belt Tools Parts T-handle hex – 4mm none Note: In most cases the alternator belt does not need to be checked any more. Early models should have the pulley and belt upgrade that came out a few years ago. Current recommendations are that the belt is installed and adjusted, then not disturbed until 36K when replacement is specified. 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Check the belt for cracks or shredding. 4. Check the belt tension, quite tight, ~1/4″ deflection when you press on the center. Note: Paul Glaves suggests that proper belt tension is when you can twist the belt ~90 degrees, midway between the pulleys. If you can twist it more than 90 degrees, it is too loose. If you cannot twist it 90 degrees, then it is too tight. 5. Leave the cover off for the valve adjustment procedure on the next page. Change Alternator Belt Tools Parts T-handle hex – 4mm alternator belt socket – 13mm ratchet wrench – 13mm torque wrench 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Loosen the 2 nuts and 1 bolt, 13mm, that hold the alternator – one is on top and one is on each side, thus allowing the alternator to pivot down. 4. Remove the old belt. (Some bikes have a pipe that traps the belt – loosen it enough to get the old belt out and the new belt in) 5. Install the new belt being sure it is properly seated. 6. BMW calls for a tensioning torque of 5.9 ft.lb. (8 Nm) on the adjuster bolt on the left side of the bike. You have to get at this bolt from the alternator side and you may have to lift the tank. Alternatively, you can pry the alternator up with a large screwdriver to tension the belt. 7. Once the belt is under proper tension, tighten the 2 nuts and 1 bolt, 13mm, to 15 ft.lb. (20 Nm). 8. Check the belt for proper tension (see above) and proper seating alignment

Incoming search terms:

HARLEY DAVIDSON CHROME UPPER BELT GUARD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION NOTE When performing the following step, it is not necessary to completely remove the shock mount bolt, back the bolt out only until it is flush with the swingarm. 1. See Figure 1. Loosen the left rear shock mount bolt (1) and back it out until the threaded portion of the bolt is flush with the swingarm. 1 2 is03762 1. Shock mounting bolt (left side) 2. Belt guard Figure 1. Loosen Shock Mounting Bolt 2. Pull the belt guard (2) straight back toward the rear of the bike to remove the guard from upper and lower grommets. See Figure 2. It may be necessary to work the guard up and down slightly to dislodge it from the upper (1) and lower (2) grommets. Remove the belt guard and discard. 2 1 3 is03763 1. Upper grommet mount 2. Lower grommet mount 3. Front belt cover Figure 2. Rubber Grommet Mount Locations 3. Obtain the chrome belt guard from kit. While making sure belt guard is over the belt, slide the guard straight in between the shock and sprocket and align cover just below front belt cover (3). The cutouts in the bracket should be lined up to engage with upper and lower grommets. NOTE When performing the following step, gently pull the guard in and out at the center; it should feel fairly tight even though the rear mounting bracket has not been secured. 4. See Figure 3. Firmly push the guard toward the front of the bike until the cutouts are secured by the grommets and the belt guard mounting bracket (1) hole lines up with the shock bolt

HARLEY DAVIDSON SKULL FOOT BOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Kit 50704-04 is an Operator Footboard Insert Kit. •This kit fits all 2004 and later FLHRS/I (Road King® Custom) model motorcycles. •This kitalso fits 1986 and later FLHR/I/CI, FLHT/C/CI/CUI and FLTR/I models equipped with Swept-Wing footboard pans 50683-04 (right) and 50688-04 (left) . Kit 50704-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50705-04 1Operator footboard insert (left) 50706-04 Kit 50707-04 is a Passenger Footboard Insert Kit. •This kitfits 2004 FLHTCSE models, and all 1986 and later Touring model motorcycles equipped with Swept- Wing Grooved Passenger Footboard Kit 50357-04 . Kit 50707-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50708-04 1 Passenger footboard insert (left) 50709-04 Kit 50710-04 is an Operator Footboard Insert Kit. •This kitfits all 1980 and later Touring models except FLHRS, and 1986 and later FL Softail®model motorcy- cles equipped with footboard pans 50621-79A. Kit 50710-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50711-04 1Operator footboard insert (left) 50712-04 Kit 50713-04 is a Passenger Footboard Insert Kit. •This kit fits all 1986 and later Touring models . •This kit also fits 1986 and later FL Softail models when equipped with accessory passenger footboard kits (Part Number 50602-89B, 50955-97A, 50955-00 or 50602-00). • This kit iscompatible with Chrome Passenger Footboard Cover Kits (Part Numbers 50782-91, 50193-96, 50194-96 and 50246-00). • This kit is notcompatible with Leather Passenger Footboard Fringe Kits (Part Numbers 50947-98 or 50956-98). Kit 50713-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50714-04 1 Passenger footboard insert (left) 50715-04 Installation, Kit 50704-04 (For Swept-Wing Operator Footboards): Removing Previously Installed Inserts 1. Apply liquid dishwashing soap to the rubber beads protruding through the bottom of the footboard pan. 2. With the operator footboard in the “up” position, use a screwdriver to work the rubber footboard beads out through the top of the footboard. 3. Repeat the above steps for the remaining footboard insert. Installing the New Inserts 4. Apply liquid dishwashing soap to the rubber beads on the new footboard insert. 5. Place the footboard insert into position on the footboard pan. From the underside of the footboard, use a pliers to pull each rubber bead into its mating hole in the footboard pan until the beads protrude through the pan. 6. Repeat the above steps for the remaining footboard insert.

Incoming search terms:

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms: