drive shaft problem on 420 honda

You search Auto repair manual PDF drive shaft problem on 420 honda, if there are search results will appear below. If search results do not exist, please search by others keyword.



  drive shaft problem on 420 honda Direct Download speed 5282 Kb/s

  drive shaft problem on 420 honda Full Version speed 6162 Kb/s



HONDA VTX, VTX RETRO AND VALKYRIE DRIVE SHAFT COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Place the cover over the drive shaft housing. 2. Hook one end of the springs provided into the lower holes. Wrap the springs around the backside of the drive shaft housing. Using a needle nose pliers stretch the springs and hook them into the upper holes. 3. Note; if springs are too long, shorten and reform end to be able to hook spring in place.

Incoming search terms:

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

KTM 3V TURBO DRIVE MODEL 9808T KNEE FEED Installation and Removal Manual

0

Filed Under (KTM) by admin on 28-01-2012

download
Gather together the following items that you will need to complete this installation. a) lathe b) 3/8″ electric hand drill c) 9/32″ diameter transfer punch SERVO Turbo Drive Model 9808T Page 2 d) .4375 drill, 3/16″ drill, #7 drill e) 1/4-20 tap f) 3/4″ socket wrench g) set of inch hex wrenches h) clean shop rag Step 2: Clean the power feed mounting area completely. Step 3: Remove the drive clutch nut and the drive clutch from the elevating jack shaft. Step 4: Remove the dial nut, dial, and dial carrier. Keep the dial for reuse later. Step 5: Remove the existing bearing retainer. Keep the screws for reuse later. Step 6: Pull jack shaft out of knee. Hold inboard end up while removing to avoid damage to the pinion gear. Step 7: Press the bearing off the jack shaft. Step 8: Drill and ream the end of the jack shaft .4375″ diameter by 13/16″ deep. The .4375″ dia. must be concentric to the shaft O.D. within .002″ T.I.R. Chamfer 1/32″ x 1/2″ diameter. For best results, machining should be done in a lathe. Step 9: Place the shaft extension #6975 into the end of the jack shaft. Finish drill 3/16″ diameter through the shaft and pin the extension with the 3/16″ diameter x 5/8″ long roll pin. File smooth. Step 10: Reassemble and replace the jack shaft in the machine. Step 11: Replace the existing bearing retainer with #57904 retainer provided. Secure using existing screws. Step 12: Slip spacer #5426 and bearing race #1616 onto the jack shaft. Slide the adaptor #0771 over the bearing race and locate against front of the knee.

Incoming search terms:

Electronic Speedo Drive for Toyota T50 5 Speed Transmission

0

Filed Under (Toyota Manuals) by admin on 20-09-2011

Download
Disassembly is simple, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” ring from the housing. Wash all parts internally and externally to remove oil, grease and road grime This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” rings from the housing. Remove the three (3) philips head screws from the cover on the top of the drive housing. Carefully remove cover, be aware that the small parts in side may be stuck to the cover. Remove all internal parts, record order of assembly. Wash housing and shaft to remove oil, grease and road grime. The T50 drive shaft needs to be shortened to a similar length to the AE101. I reassembled the AE101 shaft and housing, and then measured from the top face of the AE101 housing down to the top of the AE101 drive shaft. ( Fig.4) Record this reference depth, (I got 17mm)

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

Harley-Davidson CHAIN DRIVE INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
1) Assemble & install the chain tensioner assembly over the primary chain as shown in figure 1. 2) Install the compensator sprocket with extender & spacer (numbers 5, 6, & 7, FIG 2)(#7 is not included in this kit), primary chain, chain tensioner, and clutch basket simultaneously onto the motor drive shaft & transmission main shaft. Rotate the chain drive slightly as needed to allow the splines to line-up. 3) Install the chain tensioner nut loosely on the chain tensioner bolt. 4) Install the sliding cam onto the compensator sprocket, & slide the compensating sprocket cover-assembly (#3) over the cam. 5) Apply 2 drops of Rivera “Red” thread-lock on the threads of the motor drive shaft, & install the motor nut loosely with the fingers at this time. The hex spacer (#7) and spacer (#2) as seen in fig.2 are not provided in Rivera Engineering’s chain drive kit. These components are required with some applications, and can be purchased from your local Harley-Davidson dealer. FIG 2 6) Apply 2 drops of Rivera “red” thread-lock on the threads of the transmission main-shaft and loosely install the clutch hub nut (left hand threads). 7) Place the HD “Primary Drive Locking Tool” HD-41214 on the primary chain as shown in figure XXX and tighten the motor sprocket nut to 150-165 foot-pounds. 8)Turn the locking tool 180 degrees and move it to the clutch sprocket. Tighten the clutch hub nut to 70-80 foot pounds (left- hand thread). Adjust chain tension so that the top strand has 5/8″- to-7/8″ of up and down play (cold drive train). Tighten the center bolt nut to 21-29 foot pounds of torque.

Incoming search terms:

Honda / Acura Crank Shaft Seal Kit installation

0

Filed Under (Toyota Manuals) by admin on 17-11-2011

download
Due to the close proximity of transversely mounted engines to the shock tower, this essential tool is crucial for the
proper installation of Cam Shaft Oil Seals. Comes equipped with an exclusive expansion guide ensuring damage free installation. Applicable: Most Toyota 4 cylinder & some Mazda engines. This Special Bonus Kit was designed for the proper installation of Pulley Crank Shaft oil seals, situated within confined areas on most 4, 6 & 8 cylinder Toyota / Lexus, Nissan, Mitsubishi, Mazda and Infiniti engines. Application includes Cam Shaft oil seal installation of Toyota / Lexus 2.5L, 2.8L, 3.0L, 3.4L, 4.0L & 4.3L engines. The step bolts screw into the cam or crank shaft end. The press nut w/ washer allows for an even ressing force, seating the oil seal into the engine case every time

Honda GL1000/1100 starter motor Removal/ Over haul Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
1. Remove the three long bolts that hold the sections together and separate them. Be careful as there are a series of flat thrust washers on each end of the armature (located in the middle section). 2. The end cap basically performs no function other than to cover the brush plate and commutator area as well as center the armature shaft in a pressed in bushing located in the end of the cap. 3. The drive end contains the reduction gearing and if need be, can be disassembled to replace the bearing. This is extremely unlikely. The shaft should turn freely and normally only requires a cleaning and grease application. If the bearing in fact needs replacing, simply remove the “C” clips on either end, drive out the bearing and reinstall with an appropriate size replacement. Any decent auto parts / industrial supply should be able to supply the correct bearing. 4. Remove the brush plate from the end of the center section by removing the screw at the one brush connection. Before removing the brushes, note that one of them has an insulating sleeve over the braided wire. The replacement must go in the same brush holder. Remove the brushes and replace if necessary and clean the brush plate. ** Brake Cleaner is a good general cleaner for this entire job. 5. Remove the thrust washers from brush plate end of the armature. Count them and ensure they go back on the correct way. 6. The end of the center section that had the drive end on it has a circular plate covering it with a short splined shaft protruding through the plate. Drive the plate out by tapping the opposite end of the section on the shaft – just lightly with a rubber hammer or piece of wood to protect the shaft. Once the plate is out, remove the armature from the section. You will find more thrust washers at this end. Make sure they go back on correctly. 7. In the center of the center section there are four large Philips screws. These hold in the field coils found within the housing. Using an “impact driver”, loosen the four screws that go around the circumference of the center section and remove them. Remove the 10mm nut for the battery connection and the accompanying fiber insulating washers. With the screws and nut removed, the entire field coil assembly should withdraw entirely from the housing. There will be four (4) metal plates that the screws mounted into come falling out. They are easily replaced into the field coils when you slide it back into the housing. Do not be alarmed that you suddenly have four loose metal parts. 8. With everything out of the housing, thoroughly clean everything using the Brake Cleaner. Although the cleaner will dry without leaving a film, it is suggested that the components be dried with compressed air. 9. Get some extremely fine steel wool (“000″ of even “0000″ is better) and gently clean the metal surfaces or bars of the armature and the commutator. Blow with compressed air. 10. Using a volt/ohmeter, test for continuity between pairs of armature bars (the long ones). There should be continuity between the pairs around the entire circumference.

HARLEY DAVIDSON 45-AMP. UPGRADE ALTERNATOR ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
This 45-amp Rotor Kit is designed for installation on 1999 and later FLHT, FLHTC, FLHR, FLHRI, FLHRCI and FLTR Model Motorcycles. Existing Rotor Removal 1. Remove seat and disconnect battery terminals, negative cable first. 2. Follow instructions in applicable Service Manual and remove the primary chaincase cover. Remove the clutch, primary chain, compensating sprocket and shaft extension as a single assembly. 3. Remove the alternator rotor spacer, if present. Installation The laminated high-output rotor in this kit contains magnets that are considerably more powerful than those used in most previous rotors. The ROTOR REMOVER/INSTALLER and SHAFT PROTECTOR SLEEVE (HD-41771) must be used to prevent parts damage during rotor removal and installation. 1. See Figure 1. Verify threads are clean and thread the Shaft Protector and Rotor Remover/Installer, if removed. NOTE The Shaft Protector Sleeve not only protects the threads from the splines of the rotor, but acts as a guide to ensure that the rotor is properly centered. 2. Turn thumbscrews of Rotor Remover/Installer into threaded holes in rotor face. CAUTION 1 WARNING 1 WARNING 1 WARNING Kit Number 29999-97B Figure 1. Install Shaft Protector and Rotor Installer Engine Sprocket Shaft 1. Make Sure Threads are Clean 2. Install shaft protector sleeve. Shaft protector sleeve 3. Install Rotor Remover/Installer i04153 Handle Thumbscrew Forcing screw . Center ball on forcing screw in recess at end of engine sprocket shaft. Rotate the handle of the tool in a counterclockwise direction to ease rotor into position over stator. 4. Loosen thumbscrews and remove Rotor Remover/Installer. Remove Shaft Protector Sleeve. 5. Install the shaft extension on engine sprocket shaft. No alternator rotor spacer is necessary). 6. Follow instructions in applicable Service Manual and install the clutch assembly, primary chain and shaft extension as a single assembly. 7. Apply two drops of Red LOCTITE®262 to threads of clutch nut and engine sprocket nut. Tighten nuts as fol- lows: Clutch nut- (left hand threads), 70-80 ft-lbs (94.9-105.5 Nm) Engine sprocket nut- 150-165 ft-lbs (203-223 Nm). 8. Follow instructions in Service Manual and install the Primary Chaincase Cover using new gasket from kit, if necessary.

Honda 2007-2010 Rancher 420 ATV Rear Bumper Installation

0

Filed Under (Honda) by admin on 22-12-2011

download
Honda Rancher 420 ATV Rear Bumper (2007-2010) Installation Instructions 1. Attach top bumper attachments to top rack. 2. Attach the rear bumpers lower attachment point to vertical bars

Incoming search terms:

Incoming search terms: