drz drz400sm crankcase breather hose

You search Auto repair manual PDF drz drz400sm crankcase breather hose, if there are search results will appear below. If search results do not exist, please search by others keyword.



  drz drz400sm crankcase breather hose Direct Download speed 5282 Kb/s

  drz drz400sm crankcase breather hose Full Version speed 6162 Kb/s



Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

HARLEY DAVIDSON XL PREMIUM OIL COOLER KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to Owners Manual to drain engine oil and remove oil filter. 2. See Figure 1. Remove oil feed hose (1) from oil pump. 3. Remove oil feed hose fitting from engine crankcase. Discard oil feed hose. INSTALLATION 1. See Figure 2 and Table 1. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to oil pump. 2. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to crankcase. 3. Tighten fittings to 55-65 in-lbs (6.2-7.4 Nm) . 1 2 3 1 is04015 1. Fitting 2. Oil Hose Cooler Supply 3. Oil Hose Cooler Return Figure 2. Oil Hose Cooler Return and Supply Assmeblies 4. Loosely install oil cooler return hose assembly (3) to crankcase fitting. 5. Loosely install oil cooler supply hose assembly (2) to oil pump fitting. 6. See Figure 3 for proper oil hose routing. The oil supply hose (1) should be the upper hose and the oil return hose (2) the lower hose 1 2 is04018 1. Oil Supply Hose 2. Oil Return Hose Figure 3. Oil Cooler Hose Routing 7. Remove two existing clips holding the clutch cable and wire harness from the left frame downtube. 8. See Figure 4 and Table 1. Position oil cooler clamps (7) in approximately the same position as the clips that were removed from the frame downtube. 9. Loosely attach oil cooler (4) to the clamps (7) using screws (9) and nuts (8). 10. Attach oil return hose (3) to the inboard connection of oil cooler (4) with worm clamp (5).

HONDA VTX1300 AIR HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the rider and passenger seats, left chrome side cover & original horn located at the top of the radiator. 2. Locate the supplied black horn mounting bracket and supplied smaller hose clamp. Notice the slight twist in the bracket. Using 2 adjustable wrenches or a vise and one wrench remove the twist from the bracket. Route the hose clamp thru the bracket. (As shown in photo 1A) 3. Install the bracket on to the left frame tube, (As shown in photo 1A) and tighten securely. Bolt the supplied horns to the bracket using the supplied bolt, lock washer and nut, (As shown in photo 1) and tighten securely. Install the supplied trumpet covers (As shown in photo 1B) by flexing the spring clips over the trumpets. Check that they fit securely. If not remove covers, make sure the center screw is tight and bend spring clips in towards center of covers and re-install. Using a blade screwdriver pry the two supplied hoses with the “Y” connector off of the air horns cut a new piece of hose 3 ½” long from the hose and replace the short hose on the “Y”. Re-install the “Y” hose assembly with the short hose going on the long or upper trumpet. (See photo 1C) Re-route the original horn wires. (As shown in photo 1D) 4. From the supplied wire cut 2 pieces 28″ long. Strip ¼” of insulation from both ends. Crimp 2 supplied male terminals to one end and 2 supplied female spade terminals to the other end. Plug the male ends into the original horns wires. (As shown in 1D) Attach the remaining air hose to the “Y”. Tape the hose and wires together every 6-8″ using electrical tape to make routing easier and neater. Route the wires and hose up under the fuel tank, over the cylinder heads coming out between the frame rails at the rear of the fuel tank. (See photo 2A) Locate the supplied relay and plug the 2 wires from the original horn onto terminals 85 & 86 on the relay. (See wiring diagram on back of last page of instructions) This will be the 2 outer terminals that are parallel to each other. Locate the supplied fuse, holder & wire assembly. Crimp a supplied fork terminal to one end and a supplied female spade to the other. Attach the spade terminal to one of the remaining outer relay terminals. (#30 or 87 on wiring diagram) Remove the 3 Phillips screws from the battery top cover. Remove the cover and attach the fork end of the fuse wire to the positive (+) terminal. Re-install the battery cover. 5. Cut a wire 9″ long and strip ¼” insulation from each end, crimp a fork to one end and a female spade to the other. Attach this wire to the compressors negative (-) terminal. Cut another wire 18″ long and strip both ends. Crimp a female spade to both ends. Attach this wire to the compressor positive (+) terminal. Route the air hose out under the left side cover as shown in photo (3). Hold the compressor in place against the frame tube. Note: Looking at the large end of the compressor the space between the hose fitting and the bolt mounting flange forms a “V” shape. This is where the compressor should rest against the frame. Next loop the hose around to the compressor hose fitting and trim the hose to the desired length. Attach the hose to the compressor. Secure the compressor to the frame using 2 large supplied cable ties as shown. 6. (See photo 3A) Attach the compressor negative (-) wire to the bolt on the frame (As shown in photo 3B) Route the compressor positive (+) wire along the side up to the relay and attach to the remaining outer terminal 87 or 30. Cable tie the relay in place. (As shown in photo 2B) Use several of the supplied short cable ties to secure the compressor wires to the air hose (As shown in photo 3) as wells as any other loose wire or hose.

Incoming search terms:

HARLEY DAVIDSON EFI INTAKE MANIFOLD COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. See Figure 1. Remove screw (A) that holds the air cleaner cover (B) and seal (C). 2. Remove three T27 TORX® screws (D) to release the cover bracket (E) from the filter element (F). 3. Remove the filter element, pulling the two breather tubes (G) from hole on the inboard side of element. 4. Remove the two breather tubes (G) from the fittings on the two cylinder head breather bolts (I). 5. Remove the two breather bolts (I) and O-ring seals (K) from the air cleaner backplate (J) with a 7/16 inch deepwell socket. 6. Remove the backplate and gasket (H) from the injection module. 7. Aligning the flat edge of a new cover gasket (2) with the backplate molded tab, install a gasket (2), chrome cover (1) and second gasket, in order, on the air cleaner back- plate. 8. Install the breather bolts through the air cleaner backplate. Re-install O-ring seals onto each breather bolt. Install a washer (3) from the kit on each breather bolt. Apply Loctite 243 to the breather bolts and align holes in the backplate with the holes in the cylinder heads and install the breather bolts. Use a 7/16 inch deepwell socket and alternately tighten the breather bolts to 120-144 in-lbs (13.6-16.3 Nm) . 9. Slide gasket over the sleeve on the inboard side of filter element. 10. Install breather tubes about 1/4 inch (6.4 mm) into holes on inboard side of filter element. 11. Install breather tubes onto fittings of two cylinder head breather bolts. NOTE Air cleaner mounting without installation of the breather tubes allows crankcase vapors to be vented into atmosphere in violation of legal emissions standards. 12. Place the filter element onto backplate, with the flat side down, so that the hole on the inboard side of element fits over the molded boss in the backplate. 13. Align holes in cover bracket with those in filter element and start three screws. Stamp on cover bracket points downwards. Use a T27 TORX drive head, alternately tighten screws to 20-40 in-lbs (2.3-4.5 Nm) . 14. Make sure that the rubber seal is proper seated around perimeter of air cleaner cover and place cover on back- plate. 15. Fit the air cleaner cover onto backplate. Apply Loctite 243 to the threads of air cleaner cover screw. Install screw through cover and tighten to 36-60 in-lbs (4.1-6.8 Nm)

Incoming search terms:

YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

HONDA VTX 1800 AIR HORNS AHVTX INSTALATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2010

download
1. Remove the right and left frame side covers and the seat. 2. Unplug and remove the stock horn located behind the left foot peg. Re-route the horn wires up over the front cylinder head and to the rear. Next cut two pieces of wire 36″ long, strip both ends ¼”, crimp two male spade terminals to one end and two females to the other ends. Attach these wires to the stock horn wires and route them over the rear cylinder and behind the frame tube. The end of the wires should come out near the center of the left side cover area (see photo 1 A). Connect these two wires to the relay terminals 85 & 86 (these will be the two that are parallel to each other see wiring diagram for terminal identification). 3. Using a blade screwdriver pry the two hoses with the “Y” connector off of the air horns. Cut a new piece of hose 2 ¾” long, replace the old short hose on the “Y” with this. Re-install the “Y” hose assembly onto the horns with the short hose on the long trumpet, route the hoses behind the horns and connect the long hose to the short horn (see photo 2A). 4. Remove the upper 8mm (12mm wrench size) motor mount bolt (see photo 2B). Install the horn assembly using the 8 x 55mm bolt and spacer tube provided. If the motorcycle is fitted with Honda line tubular radiator or engine guards the above mounting will not work. You will need instead to locate the “J” shaped bracket and small hose clamp provided in the hardware kit (see photo 2 on instructions of multi -application instruction sheet). Thread the hose clamp thru the bracket and attach to the frame or Honda line guards as shown ( see photos 2&3 ) tighten the hose clamp securely using a socket or wrench. Attach the horn set to the “J” bracket using the 5/16 x ¾” bolt, nut and lock washer provided. Position the horns so that they are angled down just slightly then tighten the bolt securely. Attach the remaining air hose to the “Y” connector, route the hose up over the top and to the rear of the engine. Cross the hose over to the right side of the rear cylinder head, then behind the electricals of the right side cover and coming out as shown ( see photo 3 A & B ). 5. Remove the center relay from its mounting bracket by lifting it upward and re-attach it lower and at an angle as shown (see photo 3C) using a small cable tie. Route two long cable ties thru the hole in the relay mounting bracket as shown (see photo 3D). Next cut a 16″ wire, strip both ends, crimp female spades to both ends. Attach this wire to the compressors pos (+) terminal. Cut an 8″ wire, strip both ends, crimp a female spade to one end and a fork terminal to the other. Attach this wire to the compressors neg. (-) terminal. Cable tie the compressor securely in place as shown (see photo 4). Route the hose to the compressor making sure there are no tight bends or kinks cut the hose to the desired length and attach it to the compressor. Route the neg. (-) wire with the fork terminal up and attach it to the 10 mm bolt as shown (see photo 4A) . Route the pos. (+) wire over to the relay on the left side of the motorcycle and attach it to terminal 30 or 87 on the relay (see wiring diagram)

Air Shock Installation Instructions

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
Air HoseInstallation. Choose the most convenient loca- tiononyour motorcycle for the air fill valve. Drilla 5/16″hole and install the air fill valve as shown in Figure 3orsecure air fill valve to frame tube. 2. Keep hose ends clean during installation because dirt can cause air leaks. 3. Install hose connector, tube clamp and two O-rings onto one end of the air hose (See Figures4&5) Apply rubber lubricant (soap solution, not oil) to the O-rings to ease installation on the air hose& into the shock absorber inlet. Plastic connector should just bottom on fitting. Do not overtighten! The function of the nut is to hold everything together in place, the O- rings do the sealing. Fin- gertightenonly (10 in/lb maximum). 4. After routing the air hose, trim the length to fit air fill valve. Install hose connector, tube clamp, and twoO-rings onto end of hose (See figures 4&5). Lubricate as above and assemble to air fill valve. Use the same procedure formating hose. Important —leaveasmall amount of slack in hose near shock absorber to allow for the slight move- mentofthe shock. Caution! Do not install hose near ex- haustsystem, battery or any other sharp edges or seat movement. Keep hoses clear of moving parts such as wheels or suspension components. Do not allow hoses to have excess slack and sag below the motorcycle. The hoses could catch on road surfaces or debris and could be damaged while the motorcycle is in motion. 5. If necessary the air hose can be secured along the motorcycle’swiringharness with tie-wraps. 6. Testing: Inflate system to 50 psi. Apply soapy water solution to all connections and check for air leaks. If there are any leaks, disconnect the suspected fitting and check for dirt or damage to the air line or the O-rings. Remove any dirt or foreign matter, re-lubricate the O-rings and reinstall. If unable to locate the leak, remove rubber boot from shocks and submerge pressurized components under water (in- cludingT-Valve) and check for leaks. If you cannot solve the air leak problem, please contact our technical staff for assistance

2006 Kawasaki Ninja 650R DOT Racer Front Brake Hose Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove factory brake hoses, noting routing. Cap off master cylinder and caliper ports. 2. Install straight-bent banjo ends of Russell Left and Right hoses onto their respective calipers. Use factory single-banjo bolt from master cylinder to install Right hose onto caliper (See Fig. 1) . 3. Route hoses up through factory wire retainers to master cylinder (See Fig. 2, view from top). Use factory double-banjo bolt to install hoses onto master cylinder. Side-bent banjo of Right hose goes next to master cylinder, points toward center of bike, and rests against stop. Orient Left hose banjo so that hose runs parallel to Right hose (See Fig. 3) . 4. Locate hoses to fender using factory plastic clips around grommets on hoses at factory mounting points (See Fig. 4, Right side shown). 5. Check hose clearance throughout entire steering and suspension travel range. 6. Bleed the system and check for leaks while applying pressure

2007 Softail HARLEY DAVIDSON FUEL PUMP/ FUEL GAUGE SENDING UNIT REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
1. Remove seat. 1 WARNING 1 WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 2. Purge the fuel supply line of high pressure gasoline. a. See Figure 4-36. Disconnect the fuel pump fuse from the main wiring harness. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1 WARNING 1 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect negative battery cable. 4. Remove instrument console. a. All but FXSTD, see Figure 4-37. Remove acorn nut and washer on instrument console to separate console from fuel tank. b. For FXSTD, see 8.26 INSTRUMENT CONSOLE: FXSTD. 5. Disconnect console wiring. Figure 4-36. Fuel Pump Fuse: View From Top Figure 4-37. Acorn Nut And Washer: All But FXSTD s0660x8xx 7526
4-28 2007 Softail: Fuel System HOME 1 WARNING 1 WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00259a) 6. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. See Figure 4-38. Cut clamp (1) from one end of crossover hose (2). Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 7. See Figure 4-39. Unplug fuel pump module connector (3) [86]. 8. Remove top plate screws (2) and discard. 9. See Figure 4-40. Pull top plate (2) out of fuel tank enough to expose fuel hose and clamp (1). CAUTION Carefully inspect end of hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even the smallest hole can cause a reduction in fuel pressure. 10. Cut clamp and remove hose from regulator housing fit- ting.

Incoming search terms:

Suzuki DRZ 400E & Kawasaki KLX400E Dual Sport Kit Installation Manual

0

Filed Under (Suzuki) by admin on 13-02-2012

download
1. Remove the seat, side panels, and fuel tank. Kill switch connector Photo 1 2. Unplug and remove the stock headlight. 3. Unplug and remove the stock kill button. See Photo 1. 4. Unplug and remove the stock taillight. Using a utility knife, trim the taillight mounting tabs flush with the underside of the fender. 5. Taillight Installation: Attach the provided LED taillight to the under side of the rear fender using the provided countersunk mounting hardware as shown in Photo 2. Route the taillight wires forward to the area on top of the airbox along the right side of the fender. Secure the taillight wires to the taillight plastic with zip-ties so the tire cannot make contact. Photo 2 6. Rear Turn Signal Installation: Attach the rear turn signals to the flat portions on the sides of the LED taillight. Position them so they are out of the path of the exhaust. Route the wires forward securing with zip-ties. Route the right turn signal wires and the taillight wires around the front of the muffler mount and between the fender and the black plastic splashguard as shown in Photo 3. Route Right Turn Signal & Taillight wires here Photo 3 Page 3 of 10
7. Brake Light Switch Installation: This step requires bleeding the rear brake. If you do not feel comfortable performing this step please refer it to a qualified mechanic. Installation: Remove the guard that protects the rear master cylinder and reservoir. Temporarily remove the bolt that secures the brake reservoir to the frame. Remove the bolt that holds the banjo fitting to the top of the rear master cylinder. Replace this bolt with the provided hydraulic switch retaining the upper and lower crush washers as shown in Photo 4. Bleeding the Brakes: Do not begin this process without a fresh bottle of brake fluid. Remove the lid from the brake fluid reservoir. Put the box end of 8mm wrench over the brake bleed nipple and install the bleed hose (supplied) tightly over the nipple. Position the loop on the hose above the nipple as shown in Photo 5 with the other end of the hose in a container to catch the fluid. Crack the bleed nipple open about 1/8 to a quarter turn keeping the loop in the hose vertical. Slowly depress the brake pedal to fill the hose with fluid. Pump slowly until you have brake fluid extending up into the loop, then you can pump the pedal fairly aggressively to drive air out of the system – The fluid above the bleed nipple will prevent air from re-entering the system. DO NOT LET THE RESERVOIR GO DRY – ADD FLUID AS NEEDED. Pump the pedal until there are no more bubbles, and then close the nipple with the wrench. Double check that the pedal is firm and the brake works properly.

Incoming search terms: