ducati 696 basic tools list

You search Auto repair manual PDF ducati 696 basic tools list, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ducati 696 basic tools list Direct Download speed 5282 Kb/s

  ducati 696 basic tools list Full Version speed 6162 Kb/s



DUCATI MONSTER 696 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are approximately 3litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “EOBD engine diagnostics light” ( amber ). The engine ECU iluminates this light steadily to indicate the presence of errors leading to engine lock. 9) OVER REV indicator lights . Illuminates steadily at 800 rpm before intervention of the revlimiter. Starts flashing when the rev limiter is reached. 5 8 2 4 9 3 1 6 7 fig. 4 12 E 10) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 11) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for the LAP and USB data aquisition functions. 11 A 10 B fig. 5 13 E LCD – Main functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . 6) Air temperature indicator . 7) Lap time . 8) Rev counter (RPM) . 9) Lap time . 8 11 13 12 14 10 4 5 9 6 2 3 1 7 fig. 6 14 E 10) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indiactor will remain on the display until the system is reset by the Ducati Service Centre who carry outthe service. 11) LAP function (fig. 6). Indicates that the LAP has been activated. 12) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The relative menus are for the use of trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorised Ducati Service Centre. 13) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 14) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence.

Incoming search terms:

DUCATI TITANIUM EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Ducati) by admin on 26-10-2010

download
BILLET BRAKE RADIAL MOUNTS Moto Corse brake radial mounts are crafted by precision machine tools as shown, the caliper mount is “box” type precision tooled from single ERGAL 7075 solid piece. The result: performance, reduced weight, quality and beauty unmatched by none used extensively in moto gp as standard technology Moto Corse delivers moto gp technology for the ultimate performance. The kit is available for caliper with bolt distance 108mm or 100mm and includes all the parts to assemble it on the bike. 102143002 102143003 102143005 102143006 102143008 102143009 102143011 raDial MOunt Kit FOr OHlins rOaD &tracK Ø 43 FrOnt FOrKs FOr breMbO racing calipers screW Distance 108MM raDial MOunt Kit FOr OHlins rOaD &tracK Ø 43 FrOnt FOrKs FOr breMbO racing calipers screW Distance 108MM raDial MOunt Kit FOr OHlins rOaD &tracK Ø 43 FrOnt FOrKs FOr breMbO street calipers screW Distance 100MM raDial MOunt Kit FOr OHlins rOaD &tracK Ø 43 FrOnt FOrKs FOr breMbO street calipers screW Distance 100MM raDial MOunt Kit FOr sHOWa Ø 43 FrOnt FOrKs FOr breMbO street calipers screW Distance 100MM raDial MOunt Kit FOr sHOWa Ø 43 FrOnt FOrKs FOr breMbO street calipers screW Distance 100MM raDial MOunt Kit FOr sHOWa Ø 43 FrOnt FOrKs FOr breMbO street calipers screW Distance 100MM Ducati 999s/999r/749r Ducati 748r/996sps/996r/998r/998 eF Ducati 748r/996sps/996r/998r/998 eF Ducati 999s/999r/749/r Ducati 749/749s/999 748/998 – MOnster 1000/s4/s2r Ducati MultistraDa 1000D

Incoming search terms:

Basic Motorcycle Maintenance/ Repair Manual

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
1. Types of Motorcycles and Components a. Identify off-road, street bikes, three and four wheel cycles. b. Identify motorcycle components. 2. Demonstrate Safe Working Habits in the Shop. a. Demonstrate, list, and discuss personal safety habits. b. Demonstrate, list, and discuss shop safety. 3. Correct use of Tools (common and measuring) and Equipment a. Perform work on cycles using proper hand tools. b. Perform work on cycles using shop equipment correctly. 4. Specifications in a Shop Manual a. Locate engine tune-up specification. b. Locate engine lubrication and cooling capacities. 5. Identify and Describe Different Types of Fasteners a. Threaded and non-threaded. b. Nuts, bolts, and washers. c. Metric and English. d. Strength and Grade. e. Thread inserts. 6. Identification and Description of Engine Fundamentals a. Basic two cycle engine. b. Basic four cycle engine. c. Displacement and compression ratios. d. Horsepower and torque. 7. Disassembly, Service, and Reassembly of the Components of the Clutch and Final Drive Assembly a. Remove, measure and replace clutch components. b. Clean, lubricate, and measure chain. c. Clean and measure sprockets. d. Adjust and align rear wheel. e. Discuss shaft drive. 8. Service of Brakes, Tires, and Wheel Assemblies a. Service and adjust drum brake. b. Service disc brake caliper. c. True a wheel by adjusting spokes. d. Replace or repair a tire. 9. Attitudes and Work Habits a. Identify and develop positive attitudes toward tasks and fellow employees appropriate for the workplace, including giving and accepting criticism and praise. b. Identify and develop productive work habits, including attending to detail, completing tasks, maintaining the work setting and recording data. c. Identify and develop collaborative/teamwork skills, including solving problems in groups, building consensus, and responding to supervision

Incoming search terms:

Ducati 748 – 749 – 999 – 1098 – 848 – 1198 – Streetfighter CGS2 kit installation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
Remove body panels uppers and lowers A B C SP electronics ( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter ) 2) Place the CGS2 eBox near Dashboard. We recommend to arrange all wiring on the right side (Gear indicator display is optional) – Gear indicator display – CGS2 eBox – CGS2 main wiring – CGS2 accessory wiring (*) *NOTE: keep this wiring away from dashboard’s connector! SP electronics ( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter ) FEED SPEED CW SP electronics ( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter ) Arrange the Plug&Play wiring under Airbox and between the two strokes for right to left crossing eBox 3) Connect the Plug&Play CGS2 wiring: RPM CSS sMec SP electronics ( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter ) sMec Arrange the Plug&Play wiring under Airbox and between the two strokes for right to left crossing sMec SP electronics ( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter) 4) Connect the CGS2 sensor (sMec label) – Sensor wiring – Ducati lever senso

Incoming search terms:

2009 Ducati 696 Fuel Controller Installation and Operation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
this product fail to perform for either of the above reasons, two brothers racing will repair or replace it with an equivalent product at no charge, except for postage, to the original retail purchaser. to obtain the benefits of this warranty, the retail purchaser must return the product and proof of purchase to the place of original purchase. We recommend that this performance part be installed by a qualified motorcycle technician. If you have any doubts as to your ability to install this performance part, please consult with your local motorcycle dealer. Read all instructions first before starting installation. Make sure the vehicle and exhaust system are completely cool before starting the installation. Also, make sure the vehicle is secure during installation. Be sure to save all stock components for possible use later. The Juice Box™ is legal ONLY for closed course race vehicles. The Juice Box™ is not applicable, nor inteded for use on EMISSIONS CONTROLLED street, highway or off-road vehicles. The Juice Box™ is not applicable, nor inteded for use on aircraft. Thank *you*for*purchasing*a*genuine*Two*Brothers*Racing* JUICE*BOX™. **This*product*represents*a*radical*step* forward *in*tuning*fuel-injected*motorcycles*and*ATVs*for* optimal *performance*using*”load-based”*technology.** We *at*Two*Brothers*Racing*hope*that*you*will*find*this* development *as*exciting*and*useful*as*we*do. **And* remember: **Proper*Fuel*=*Maximum*Power! Make *sure*the*vehicle*is*completely*cool*before*starting* the *installation. *Also, *make*sure*the*vehicle*is*secure*and* will *not*roll*around. * Remove *the*seat*assembly. * Remove *the*fuel*tank*top*cover*screws. * (fig.1) Remove *fuel*tank*top*cover. * (fig.2) Remove *side*fuel*tank*covers. * (fig.3) Remove *fuel*tank*by*removing*lower*bolt*that*secures* tank *from*sliding*rear-ward. * (fig.4)

DUCATI MONSTER S4R And DUCATI MONSTER S2R EXHAUST SYSTEM Installation instructions

0

Filed Under (Ducati) by admin on 26-10-2010

download
REMOVAL OF STOCK EXHAUST SYSTEM: 1. Put the motorcycle on a side stand, we recommend a racing stand. Make sure, that surface is solid and flat. 2. Remove stock heat shields (Figure 1, 2) 3. Unscrew the bolts from the metal clamps at the muffler – collector joints (Figure 3, 4). T-handle 10mm wrench T-handle 12mm wrench T-handle 13mm wrench T-handle 3mm three hexagon key wrench T-handle 5mm three hexagon key wrench Combination 13mm wrench Spring puller Figure 1 Figure 2 Figure 3 Figure 4
NAV – 124 3 Figure 10 Figure 7 Figure 8 4. Unscrew the bolt from the muffler chassis hanging bracket and remove both mufflers with link pipes (Figure 5, 6). INSTALLATION OF THE AKRAPOVIC SLIP-ON EXHAUST SYSTEM: 1. Slide the link pipes onto the stock collector (Figure 7) hand tighten the metal clamps at the Akrapovic link pipe – stock collector joints; coat the interior side of the metal clamps and the clamp bolts with Akrapovic anti-seizing copper paste (black tube) (Figure 8). 2. Install Akrapovic carbon-fiber chassis hanging bracket (Figure 9, 10). 22Nm 16ftlb Figure 5 Figure 6 Figure 9 NAV – 124 4 Figure 15 3. Position the muffler correctly and slide it onto the outlet side of the link pipes and attach the springs; WARNING! make sure, that springs pull the muffler all the way onto the link pipes – use rubber mallet if necessary to tap the connections into place! (Figure 11, 12). 4. Correctly position the carbon-fiber clamp and slide it onto the muffler – bear in mind the left offset of the carbon-fiber clamp viewed from the rear. WARNING: open the clamp slightly wider than the diameter of the outer sleeve of the muffler – do not scrape it along the muffler outer sleeve! (Figure 13). Tighten the carbon-fiber clamp onto the Akrapovic carbon- fiber chassis hanging bracket (Figure 14, 15). Make sure the link pipes or muffler are not touching the frame or any other part of the motorcycle.

Incoming search terms:

DUCATI MONSTER 1100 / 1100S Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . ) Lap time . 7) Rev counter (RPM) . 8) Lap time . 7 10 12 11 13 9 4 5 8 2 3 1 6 fig. 6 14 E 9) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indicator will remain on the display until the system is reset by the Ducati Service Centre whocarry outthe service. 10) LAP function (fig. 6). Indicates that the LAP has been activated. 11) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The related menus are for use by trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorized Ducati Service Centre. 12) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 13) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence. OFF CHECK 1 fig. 7 16 E It then reverts to “normal” mode and, in place of the motorcycle speed, shows the model and, for 2 seconds, alsothe version (EU, UK, USA, CND, FRA, JAP). The model is scrolled on the display onceonly. CHECK 2 RUN fig. 8 17 E At Key-On, the instrument panel always shows the following information (de-activating any previously activated functions): Odometer Speed Engine rpm bargraph Engine oil temperature bargraph At this point, with button (1, fig. 9) in position B “▼” it is possible to switch from the odometer display function to thefollowing functions: TRIP TRIP FUEL (only if active) Clock before returning to TOT (odometer function). If, however, you press switch (1, fig. 9) in position A “▲”, thesystem enters MENU mode and displays the following functions in sequence: Error (only if active) BATT RPM LIGHT SET LAP (OFF or ON) LAP MEM DDA (OFF or ON) Erase DDA TIME Set CODE (only if active)

Incoming search terms:

YAMAHA FZS 600 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-11-2010

download
CHECKING THE CONNECTIONS Check the leads, couplers, and connectors for stains, rust, moisture, etc. 1. Disconnect: lead coupler connector 2. Check: lead coupler connector Moisture Dry with an air blower. Rust/stains Connect and disconnect several times. 3. Check: all connections Loose connection Connect properly. If the pin 2 on the terminal is flattened, bend in up. 4. Connect: lead coupler connector Make sure that all connections are tight. 5. Check: continuity (with a pocket tester) Pocket tester 90590-03112 If there is no continuity, clean the termi- nals. When checking the wire harness, perform steps 1 to 3. As a quick remedy, use a contact revitaliz- er available at most part stores.
1-5 GEN INFO SPECIAL TOOLS 1 2 1 2 1 2 1 EB104000 SPECIAL TOOLS The following special tools are necessary for complete and accurate tune-up and assembly. Use only the appropriate special tools as this will help prevent damage caused by the use of inappropriate tools or improvised techniques. When placing an order, refer to the list provided below to avoid any mistakes. Tool No. Tool name/Usage Illustration 90890-01268 Ring nut wrench This tool is used to loosen and tighten the steering ringnut. 90890-01304 Piston pin puller This tool is used to remove the piston pin. 90890-01460 -01326 Damper rod holder T-handle These tool ar used for holding the damper rod when removing or installing the damper rod. 90890-01312 Fuel level gauge This gauge is used to measure the fuel level in the float chamber. 90890-01325 -01352 Radiator cap tester Adaptor These tools are used for checking the cooling system. 90890-01362 -01382 Flywheel puller Crank shaft protector These tools are used for removing the rotor and starter clutch. 90890-01367 -01381 Fork seal driver weight Fork seal driver attachment (ø41 mm) These tools are used when installing the forkseal.

Incoming search terms:

DUCATI 1098 DIRECT LEVER INSTALLATION MANUAL

0

Filed Under (Ducati) by admin on 26-10-2010

download
Ducati direct lever sensor installation: 1) Remove original lever assembly 2) Fit the new lever and tight nut. 3) Set toe peg in correct position 4) Connect the sensor with CGS2 and try it: when sensor is pressed a dashes appears on CGS2 SP electronics DUCATI DIRECT LEVER SENSOR INSTALLATION NOTE – The sensor was designed to offer you the best performance and don’t need mechanical maintenance: you mustn’t disassemble or try to repair the lever (See warranty details on our website www.spelectronics.it). – If you intend use our lever sensor with your preferred quick shifter electronic system (Power Commander, Rapid Byke, ecc.) we recommend you to use specific wiring interface (see photo below). Alls connector manipulations on sensor invalidate warranty. SP electronics DUCATI DIRECT LEVER SENSOR INSTALLATION SP electronics is working everyday to improve quality on our products. Unfortunately, perhaps some sensor doesn’t work after some time. Remember that SP electronics will apply warranty substitutions or repairs when products satisfies original complying

SUSPENSION SERVICE TOOLS/ FORK DAMPER ROD BLEED TOOL

0

Filed Under (Tips and Review) by admin on 30-11-2010

download
33 SHOP EQUIPMENT & TOOLS SUSPENSION SERVICE TOOLS K&L FORK TUBE U-BLOCKS Precision machined from billet aluminum, these quality three piece sets are a handy, accurate and safe way to straighten and check fork tubes. 35-9411 36mm (for 33 thru 36mm tubes) 35-9412 40mm (for 37 thru 40mm tubes) 35-9413 43mm (for 41 thru 43mm tubes) 35-9414 46mm (for 44 thru 46mm tubes) 35-1964 35-8579 35-7995 DAMPER ROD HOLDERS Holds damper rod when disassembling forks. 35-8578 Yamaha front forks, 43mm Kayaba YZ125/250 (1988) YZ490 (88-90) 35-8579 Yamaha YZ125/250 with UD(upside down) forks FORK DAMPER ROD TOOLS Sold each. 35-7995 Combination Fork Damper Tool Designed to hold the damper rod during assembly & disassembly of Honda XR400′s or Suzuki DR-Z400S. One end features spanner type prongs for the XR400 and the other a 27mm hex for Suzuki. 35-1964 Combination Damper Rod Fork Tool Designed for assembly and disassembly of most inverted Kayaba and Showa 41mm, 43mm, 46, and 47mm forks. Use one end for Kayaba forks and the other for Showa forks. (not required for 91-92 Honda CR models) ROD HOLDER Double sided damper rod holder. Works on Kayaba U.D (upside down) 41mm forks. 35-8580 Yamaha YZ125/250Amodels (89-90) FRONT FORK CAP SOCKET Designed to remove and install Yamaha front fork caps with female hex head. Sold each. 35-8571 14mm female socket 35-8573 19mm female socket FORK DAMPER ROD HOLDERS Holds damper rod when disassembling and assembling front forks. 35-8576 Use for Yamaha 43mm Kayaba forks, 30mm hex YZ125 (84-87), YZ250 (81-87) IT250 (1983) YZ490 (82-87) 35-8577 Use for Yamaha 38mm Kayaba forks, 24mm hex YZ125 (81-83), IT175 (82-83), IT250 (81-82) YZ250 (77-80), YZ400 (77-79), IT465 (81-82) FORK CAP WRENCH Designed to remove the front fork caps on late model Honda CR’s and Suzuki RM’s. Can also be used for adjusting compression. One end of wrench is 49mm, the other is 50mm. Sold each. 35-7803 Fork Cap Wrench 35-8576 35-8577 35-8571 35-8573 6 Point Hex 35-8578

Incoming search terms:

Incoming search terms: