dyna access download

You search Auto repair manual PDF dyna access download, if there are search results will appear below. If search results do not exist, please search by others keyword.



  dyna access download Direct Download speed 5282 Kb/s

  dyna access download Full Version speed 6162 Kb/s



HARLEY DAVIDSON DYNA SPROCKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1991-1992 Dyna models: Screw (5) 3739A 1993-1995 FXDL, 1995 FXD and FXDS, all 1997-1999 Dyna models: Screw (5) 3730A 1993-1995 FXDWG and all 1996 Dyna models: Screw (5) 3769 1991-2005 Dyna models: Washer (5) 6516HW 2000-2006 Dyna models: Screw, with lock patch (5) 3737A 2006 Dyna models: Screw, with lock patch (5) 3873 2007 and later Dyna models: Screw, with lock patch (5) 3109 The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) Kit Contents There are no Service Parts available with this kit. INSTALLATION NOTES The cotter pin or spring clip for the rear axle nut must be replaced during assembly and is available for purchase from a Harley-Davidson dealer. The five sprocket mounting screws must be replaced when replacing the sprocket. Remove existing sprocket according to service manual instructions. Remove all residual threadlocking agent from fastener holes using an appropriate thread chasing device and compressed air.

Incoming search terms:

DYNA IGNITION COIL INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 08-11-2011

download
Remove the gas tank. Locate the two ignition coils. 2) Unplug the primary wires coming from the coils and disconnect the high voltage wires from the spark plugs. Remove the coil mounting bolts, and remove the coils. 3) Cut or unsolder primary wires from coils. Crimp or solder ring terminals supplied with kit to primary wires.4) Attach the primary wires to the DYNA COILS using the 10-32 x 5/16 pan head screws provided. Either wire can be mounted on either terminal of the dual output coils as they have no polarity. On the single output coils, the primary terminal opposite the side with the output tower has a + marking. Plus 12 volts from the ignition switch is applied to that terminal, and the points or ignition system output is connected to the other terminal. On a Kawasaki, make sure there is clearance between the screw head and the mounting screw spacer. Do not over- tighten screws as damage to the coil could result. 5) Using the stock hardware, mount the coils to the frame in the original location. NOTE: The DYNA COIL mounting hole spacing is designed to accommodate early model Honda, Kawasaki, and Suzuki motorcycles. There are a wide variety of physical sizes and mounting configurations on the late model motorcycles and it may e necessary to modify existing mounting brackets, or fabricate a bracket to adapt the DYNA COILS to your particular motorcycle

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

2007-2010 Harley Davidson Dyna EFI Tuner INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through to the back side of the electrical box (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Dat a plug Remove bolt Remove bolt s FM814 www .fuelmotousa .com 2007-20 1 0 Harley Davidson Dyna – FM EFI Tuner – 2 8 Lay the PCIII behind the electrical box temporarily. 9 Route the GREYconnector from the PCIII through the back of the electrical box and plug it into the ECM (Fig. D). 10 Connect the stock wiring harness to the BLACK connector of the PCIII. 11 Zip tie these connectors to the front side of the electrical box (Fig E). Make sure they are situated away from the rear exhaust pipe. Fig. D Fig. E PCIII connector Stock connector PCIII connector 12 Mount the PCIII to the underside of the stock ECM (Fig. F) using the supplied velcro. Make sure to clean both surfaces with the alcohol swab before attaching. Situate the PCIII so the USB and expansion ports point to the rear of the bike. This will allow you easier access to adjust the maps if necessary

Incoming search terms:

HARLEY DAVIDSON DYNA SIDESHOTS BLACK INSTALLATION AND REMOVAL PROCEDURE

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove seat to gain access to rear oxygen sensor connector. Unplug sensor and feed end of wire through frame so that it is free from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Remove two bolts holding rectifi er onto front of frame (near front tire). Open plastic cover to gain access to front oxygen sensor connector. Unplug sensor from harness. Remove cable tie holding wire to frame and feed end of wire through so that it is free from motorcycle. 3. Loosen heat shield clamps on both the front and rear head pipes. 4. Remove two cylinder exhaust port fl ange nuts from each head pipe, located at the cylinder head. 5. Remove front head pipe clamp bolt. 6. Remove the bolt that attaches muffl ers to the frame mounting bar. 7. Remove the complete exhaust system and set aside. Assistance may be required. 8. Remove stock mounting bar and the studs in the transmisson cover. Save the bolts, one will be re-used. 9. Remove left bolt below the transmission cover. Position mounting bracket 405-P over mounting location to determine which bolts to remove (Figure 1). Install this bolt in the top hole left vacant by the new bracket. 10. Carefully remove the fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check condition of stock exhaust gaskets. Replace if worn or damaged. (Recommended replacement exhaust port gaskets, Screamin’ Eagle part number 17048-98)

HARLEY DAVIDSON DYNA GLIDE CUSTOM SEAT KIT Installation Instructions

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
Installation When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with metal tabs on seat. 1. Remove existing seat from motorcycle. Keep lockwasher and screw. 2. Remove existing grab strap and all attaching hardware. 3. Install new grab strap onto motorcycle at same location old grab strap was removed (re-use existing hardware). 4. On all models, except FXDWG , install existing stock rear bracket onto seat using stock hardware. On FXDWG models, install the new rear bracket, 52152- 97 onto the seat using the stock hardware. 5. Position new seat on motorcycle. Be sure bracket on front of seat fully engages seat mounting tab on frame. NOTE On rear fenders of 1997 -2003 models, a captive nut secured with a plastic retention washer has replaced the previously used weld nut. Do not remove the plastic retention washer unless the captive nut is damaged and must be replaced. The plastic retention washer also prevents seat bracket from contacting paint on fender. Therefore, no nylon washer is required between bracket and fender on 1997 – 2003 models. 1996 DYNA MODELS ONLY Secure seat with stock screw, stock lockwasher and place stock nylon washer between seat bracket and fender. 1997 – 2003 DYNA MODELS Secure seat with stock screw and stock lockwasher.

Incoming search terms:

DYNA III ELECTRONIC IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
1)Fasten the clamp to the electronic module using the 4-4O x 5/16 screws and lockouts provided. The damp and nuts go on the inside of the case. 2)Remove the fuel tank. Attach the module to the frame in the location selected. Cut off excess clamp material. 3)Remove an engine case or valve cover bolt and fasten the ground lug (black wire) securely to the engine. DO NOT ATTACH TO FRAME. 4])Locate the two ignition coils (they are positioned behind the left side cover on some models). There is a white wire going to the positive side of one coil that carries the switched 12 volts. A short blue/black wire then connects that point to the positive side of the other coil. Connect the separate red wire included with the kit to the spare spade terminal that is available on the positive terminal of the second coil. 5)Plug the red wire coming from the electronic module into the red wire installed in Step 4. 6)Remove the cap from the contact breaker housing. Remove the alternator cover, timing mark inspection plug, and spark plugs. 7)Remove the two screws and clips holding the points plate to the housing. Remove the screws holding the condensers to the housing. Disconnect the red and green wires where they plug into the wire harness (or coils), and remove the entire points/plate/condenser assembly. 8)Make sure the top of the housing is clean. Place the DYNA III sensor plate on the housing and orient it so that the wires exit to the rear. Place one of the original wire grommets on the front end of the plate and secure it with the screw and clip previously removed. Route the sensor cable wires through the other grommet (2 wires in the largest hole) and secure with the other screw and clip. Before tightening the plate screws, make sure the plate does not obstruct the cap screw holes. 9)Using a hex wrench in the alternator bolt, rotate the engine forward until the right hand cylinder is at top dead center on the compression stroke (D mark aligned with index mark on engine case). 10) Make sure the points cam is free of dirt and grease, and slip the DYNA III rotor over the cam Push the rotor down until it’s flange is in contact with the top of the cam. Orient the rotor so that the mark on top aligns with the line on the left (right cylinder) sensor. While pushing down on the rotor, tighten the set screws using the alien wrench supplied with the kit. 11)Rotate the engine by hand and check run-out (wobble) of rotor by watching the rotor/sensor gap. If the rotor is installed correctly, there should be no more than . 005 run-out, and it should not come in contact with either sensor. As a final check, turn the engine with the electric starter and observe the run-out. 12)Connect the three sensor cable plugs to the module receptacles, matching the red, white, and black wires. 13)Plug the remaining red and green wires onto the spade terminals where the original points connected, matching the colors

HARLEY DAVIDSON DYNA REAR AXLE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Models This kit fits 2006 Dyna models. This kit does not fit on motorcycles equipped with saddlebags. Kit Contents See Figure 1 and Table 1. INSTALLATION 1. Place axle covers in position over ends of swingarm with the deeper cover on the left side (covering the axle nut). 2. Fasten the clamping bars (3) to the backs of the covers using hex-head screws (5) and Belleville washers (4), securing the covers to the swingarm. Tighten the hex-head screws to 21-27 in-lbs (2.4-3.0 Nm) . Do not overtighten SERVICE PARTS 4 1 3 4 5 2 3 5 is00709 Figure 1. Service Parts: Dyna Swingarm Axle Cover Table 1. Service Parts Table Part Number Description (Quantity) Item Part Number Description (Quantity) Item 45159-97 Washer, Bellville (4) 4 Not Sold Separately Axle cover, left side 1 3644 Screw, #10-24 x 1/2 inch (4) 5 Not Sold Separately Axle cover, right side 2 Not Sold Separately Clamping bar (2) 3

2004-2005 Harley Davidson Dyna EFI Tuner Installation Manual

0

Filed Under (Harley Davidson) by admin on 14-04-2012

download
1 Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through the box and into the small opening in the frame (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Data plug Remove bolt Remove bolts FM810 www. fuelmotousa.com 2004-2005 Harley Davidson Dyna – FM EFI Tuner – 2 8 Plug the black connector of the Power Commander into the stock wiring harness connector (Fig. D). 9 Route the grey connector of the Power Commander through the box and plug it into the ECM. 10 Install the Power Commander against the rear part of the electrical box. Make sure to clean both surfaces with the alcohol swab first. Use the supplied velcro to attach the Power Commander. 11 Bolt the box back into place. 12 Reinstall the seat. Fig. D Fig.

Incoming search terms:

HARLEY-DAVIDSON DYNA BIGSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-03-2012

download
1. Remove seat to gain access to rear oxygen sensor connector. Unplug sensor and feed end of wire through frame so that it is free from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Remove two bolts holding rectifi er onto front of frame (near front tire). Open plastic cover to gain access to front oxygen sensor connector. Unplug sensor from harness. Remove cable tie holding wire to frame and feed end of wire through so that it is free from motorcycle. 3. Loosen heat shield clamps on both the front and rear head pipes. 4. Remove two cylinder exhaust port fl ange nuts from each head pipe, located at the cylinder head. 5. Remove front head pipe clamp bolt. 6. Remove the bolt that attaches muffl ers to the frame mounting bar. 7. Remove the complete exhaust system and set aside. Assistance may be required. 8. Remove stock mounting bar and the studs in the transmisson cover. Save the bolts, one will be re-used. 9. Remove left bolt below the transmission cover. Position mounting bracket 390-P over mounting location to determine which bolts to remove (Figure 1). Install this bolt in the top hole left vacant by the new bracket. 10. Carefully remove the fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check condition of stock exhaust gaskets. Replace if worn or damaged. (Recommended replacement exhaust port gaskets, Screamin’ Eagle part number 17048-98). 11. Remove stock oxygen sensors, they will be re-used on new system

Incoming search terms: