dyna swing arm rubber bushing removal

You search Auto repair manual PDF dyna swing arm rubber bushing removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  dyna swing arm rubber bushing removal Direct Download speed 5282 Kb/s

  dyna swing arm rubber bushing removal Full Version speed 6162 Kb/s



Harley Davidson Softail Drive Side Brake System Installation Manual

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
Removing The Stock Components Although the PM Drive Side Brake System can be installed with the swing arm bolted to the frame, we recommend removing it for better access as well as repainting. Begin by removing rear wheel,stock brake components and belt guard from swing arm. Photo #1 Using supplied 3/4 x 2″bolt,position Drive Side BrakeAssembly on swing arm. Slide assembly to center position of tab and axle spans. Making sure brake mounting tabs are flush with swing arm,snug 3/4 x 2″ bolt to hold assembly and mark swing arm area to be ground Photo #2 . Remove entire assembly from swing arm and thoroughly grind paint away from marked areas Photo #3 . Photo #4 Re-mount assembly to swing arm and slide to rear-most position of both axle and brake mounting tabs. Confirm that brake tabs are flush with swing arm and parallel to each other. Snug 3/4 x 2″bolt and 5/16″socket head cap screws in tabs to hold assembly during welding process. Warning Center the motorcycle on the lift so that it will not fall while you are working on it. Photo #6 Photo #5 Photo #7 Photo #9 Welding Tabs to Swing Arm Note PM recommends all welding be done by a certified welder. Photo #5 Tack weld rear of tabs to swing arm. Avoid excessive welding near brake as- sembly as heat can mar finish. Loosen socket head cap screws and 3/4″bolt,Slide entire assembly to forward most position and re tighten bolts Photo #6 (movement should require minimal effort if tabs are aligned properly) and tack front of tabs to swing arm. Remove brake assembly from swing arm. Weld tabs to swing arm.Verify alignment of tabs, as they must remain parallel to each other. Repaint swing arm and re-install on bike to factory torque specs. Installing Brake Assembly Remove primary bracket from tower assembly (this allows bracket to be installed without having to line up caliper on disc) by removing the three 5/16″socket head cap screws (commonly called allen bolts). Photo #7 Mount rear tire and bolt pulley to rear wheel. Place disassembled bracket against pulley using smaller of two supplied spacers between bracket and pulley. Slide wheel/brake assembly into swing arm. Place large spacer on right side and slide axle in. Do not tighten axle at this point . Photo #8 Slide caliper/tower assembly over disc and install 5/16″x 1″socket head cap screw in center hole to position assembly Photo #9 . Snug, but do not tighten bolt at this point.

Incoming search terms:

1987 to Current Harley Davidson Softail (FLST Only) Motorcycle Trike Conversion removal and Installation Guide

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Seat (to be re-installed without modification). • Left and right saddle bags (if so equipped). • Left and right rear crash bars, saddlebag rails (if so equipped). • Left and right passenger foot rests (to be re-installed without modification) • Complete exhaust system (to be replaced with new system). • Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake caliper is removed • Remove Rear Caliper (disconnect brake line at caliper) NOTE: Cap line to prevent introduction of dust / debris into line. Remove caliper. • Rear Drive Pulley (1987-99 models to be re-installed without modification). • Rear Fender (2000 and newer models, fender mount plates to be reused). • Swing Arm NSTALLING TRIKE CONVERSION KIT 3.1 Sprockets and Drive Belts Specifications See following table for belt installation (1987-99 will use a 4 tooth longer belt) Note : See OEM manual for belt replacement procedure. Year Drive Sprocket OEM Belt New Belt / Sprocket 1987-92 70 T 132 T 136 1993-94 61 T 128 T 132 1995-99 65 T 130 T 136/70TOEM 2000-06 Champion Sprocket, 70 T 135 T Use OEM 2007 Up Champion Sprocket, 66 T Use OEM 3.2 Install Swing Arm É Noting size and location of bolts, remove Cross Assembly from Champion Swing Arm. Do not discard hardware. Figure 1 3.2.1 1987-99 Model Years • Remove bearings from OEM Swing Arm using OEM shop tools and hydraulic press. Note : Although original bearings can be re-used, it is HIGHLY recommended that NEW bearings be installed to Champion Swing Arm a. b. Press bearings into Champion Swing Arm in the same way as the OEM Swing Arm. Using OEM Spacer Tube and supplied washers (four ¾” flat washers), install Champion Swing Arm using OEM bolt, outside washers and nut. Do not torque pivot bolt nut at this time. Figure 2 Note : Insure belt path is over and under Swing Arm pivot. c. d. Replace cross assembly and hardware (previously removed in step 3.2) to Champion Swing Arm. Note that the 2 upper left hand side bolts are countersunk. Torque pivot bolt to OEM specification

Incoming search terms:

TRIUMPH ROCKET III SWING ARM COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-12-2010

download
1. Locate and remove the 6mm screw which secures the rear brake hose clip to the top of the swing arm (just in front of the lower right shock absorbers mounting point. 2. Notice the double faced adhesive tape on the inside of the cover and where it will contact the swing arm when installed, clean this area with rubbing alcohol and remove the backing from the adhesive tape on the inside of the cover. 3. Place the ¼” washer provided on the top of the swing arm over the brake hose clip mounting hole. Starting at the rear of the swing arm slide the cover carefully into place and align the small hole in the top of the cover with the washer and the threaded hole. Place the screw thru the hose clip then the cover and finally the washer, next thread the screw into the hole finger tight only. 4. Press the front area of the cover with the adhesive tape firmly into place. Tighten the 6mm brake hose clip screw securely.

TRIUMPH ROCKET III SWING ARM COVER INSTALLION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Locate and remove the 6mm screw which secures the rear brake hose clip to the top of the swing arm (just in front of the lower right shock absorbers mounting point. 2. Notice the double faced adhesive tape on the inside of the cover and where it will contact the swing arm when installed, clean this area with rubbing alcohol and remove the backing from the adhesive tape on the inside of the cover. 3. Place the º” washer provided on the top of the swing arm over the brake hose clip mounting hole. Starting at the rear of the swing arm slide the cover carefully into place and align the small hole in the top of the cover with the washer and the threaded hole. Place the screw thru the hose clip then the cover and finally the washer, next thread the screw into the hole finger tight only. 4. Press the front area of the cover with the adhesive tape firmly into place. Tighten the 6mm brake hose clip screw securely.

Yamaha Road Star Motorcycles Trike Conversion Removal And Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model. nstallation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster plates. Figure 3 Qty per Assm Spec Description 2 M10 x 1.25 x 70 Hex Head Bolt 2 M10 x 1.25 Hex Nut b. Install adjuster plates to rear drive pinch blocks. Hardware installs from inboard to outboard side. Snug, but do not tighten hardware at this time. Figure 4

Incoming search terms:

HARLEY DAVIDSON Softail Big Shots Staggered Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. If equipped, loosen the floor boards to gain clearance for exhaust removal and installation. 2. Loosen heat shield clamps on both the front and rear head pipes. 3. If equipped, loosen crossover pipe clamp, located between front and rear head pipes. 4. Remove two cylinder exhaust port flange nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach mufflers to the frame. 6. Remove the complete exhaust system and set aside. Assistance may be required. 7. Remove stock mounting bars and brackets. 8. On models equipped with upper mounting bar attached at swing arm pivot bolt, go to step 9. If upper mounting bar is attached with two torx bolts (not swing arm bolt) go to step 10. 9. Remove right side 1/4″-20 bolt which holds lower fender in place. The fender will flex outwards allowing removal of right passenger foot peg bolt. Park the motorcycle on its side stand. Position a floor jack under right hand frame tube of the motorcycle below swing arm pivot bolt. Raise jack just enough to take the weight off swing arm pivot bolt. Remove swing arm pivot bolt and stock upper mounting bar. Replace swing arm pivot bolt and torque to 120 ft. lbs. Reinstall passenger foot peg using 1/2″-20 x 3″ bolt and 1 5/8″ long spacer (supplied). Reinstall 1/4″-20 fender bolt. 10. Using a T50 torx driver, remove the three mounting bolts and mounting bar. (Two of the bolts are visible, the third also attaches right hand passenger foot peg pivot and is accessed by removing foot peg. Reinstall foot peg using 3/8″x 2-1/2″ Allen bolt and 3/4″ long spacer (supplied). 11. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. (Recommended replacement exhaust port gaskets, Harley part number:17048-98 or 65324-83A)

Incoming search terms:

YAMAHA ROADSTAR/ WARRIOR ADJUSTABLE REAR LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Secure motorcycle to a bike lift and raise the motorcycle. Rear wheel should remain barely resting on the ground. 2. See diagram on page 2 for references made in parentheses, for example (#5). 3. Remove the nut from the rear suspension bolt (#5) at the bottom of the shock (#7). You may need to remove your exhaust and rear horn to access the nut and bolt. 4. Remove this suspension bolt (#5) from the non-exhaust side of the bike. You may need to raise or lower the bike to ease the tension on the bolt in order for it to come out. 5. Next remove the nut (#4) and bolt connecting the relay arm (#3) to the swingarm. From here remove the entire shock assembly and relay arm from the bike. For ease of re-installing the relay arm (Step 8) and shock be sure to take precautions that in removing the assembly, you can put it back the same way you took it off. Flipping of the relay arm can cause serious damage to the lowering kit and surrounding components. 6. Remove the two suspension arms from the relay arm(#3) and shock(#7). Compare stock arm to length of lowering arm you are about to install. Make sure the length of the lowering arm matches the link of the stock arm. To set how much you want to lower the bike, lengthen the lowering arms. Every 1/4″ longer than stock is approximately 1″ of drop. Do not lower the bike more than 2″ for safety reasons. To adjust, unscrew the large hex shaft from the threaded rods. Make sure to adjust length equally on both shafts. Be sure to tighten all jam nuts once desired lowering position is set. 7. Re-assemble the lowering arms to the top of the shock (#7) using the supplied collar, nut, and bolt. The stock collar (#6), the one in the eyelet at the top of the shock (#7), will need to be removed as it is too long. (This is because the heims are thicker than the stock arms) Do not tighten the nut, or re-install into the frame yet. 8. Re-install the relay arm (#3) to the swingarm. The large hex shafts go to the rear of the bike. This is where it

Incoming search terms:

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

INSTRUCTIONS ON HOW TO R & R YOUR Swingarm

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
• Upgrade Your Pre- 2002 FL Or FXR Rear Fork & Get Rid Of The Crappy & Dangerous (Cleve Blocks) & Replace Them With A Stable System. • R & R your Swing Arm, Belt Drive, Swing Arm Pivot Shaft, and Rear Wheel. The paragraphs below are a photo journey into the replacement of a FL or FXR swing arm. To upgrade the pre 2002 FL, here is a How-To on cheaply replacing the poor parts Harley stuck you with. Now – Let’s Get Er’ Done • Pre- 2002 had weak swing arms and are known to fail. The cleve blocks are the cause of “Rear Steer” or “Rear Fork Deflection”. Harley came up with a patch in 2002, using bearings. Because the pre 2002 transmissions have a 5/8″ mounting hole for the 5/8″ swing arm pivot shaft, a conversion unit has been made. No transmission removal for boring is necessary. Under no circumstances, do I recommend drilling out the transmission case with a hand drill. The drill will “wander” (drift)! • Solution: Go to either a trike shop/manufacturer, e-Bay, or shop and buy a new style swingarm. Harley made an additional upgrade in 2007, try and buy this type 2007 & above). If upgrading to a 2008, Harley use 25mm (smaller than 1″) axles & wheel bearings, you will have to use 25mm bearings. With that said, let’s get on with it. • In the case of a 2007 swingarm; buy and do not pay over $40 for the swing arm and axle. You must use the corresponding axle as a ¾” axle set-up is different (along with wheel bearings & spacers). You positively can not use a pre -2002 HD stock wheel because the wheel bearing spacer will fit into the wheel. Buy 2002 & above style wheels as they (9 spoke) are cheep. • You are going to have to either bore out your stock rear caliper bracket or better still, upgrade your whole rear brake to the new model & sell yours on e-Bay. • I recommend doing the following before hand and have it ready for installation; Remove bearings et al. from the 2002 & later swing arm via press. Bike Work: • Jack up your bike using a center jack. Secure the bike so it will not fall over. You can also use a motorcycle jack. I use a motorcycle dolly

Incoming search terms:

HARLEY DAVIDSON DYNA DOCKING HARDWARE FOR FXDX WITH WIDE TIRE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
Installation NOTE Perform the following procedures on one side of the motorcycle until instructed to go to the other side. To keep fender in alignment the front docking point will be mounted first. INSTALLING DOCKING POINTS NOTE Save the acorn nuts and washers removed from the fender support bracket for use when installating docking points. 1. Loosen and remove the acorn nuts, washers, and screws from the fender support (right-hand) bracket. Save the washers and acorn nuts for docking point installation. Discard screws. 2. Obtain 1 plastic bushing, labeled 01, from a bushing set. 3. Place the bushing (4) (beveled side out) into the front support hole as shown in Service Parts illustration. 4. Place the countersunk side of the front docking point (2) so that it engages bushing (4). 5. From underneath (inside) the fender, insert hex-head screw (1) through fender, support bracket and front docking point (2). 6. Install washer (7) split lockwasher (5) and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 7. Obtain another plastic bushing, labeled 01 , from the bushing set. 8. Place bushing (4) (beveled side out) into the the rear support hole as shown in Service Parts illustration. 9. Place the countersunk side of the rear docking point (3) so that it engages bushing (4). 10. From underneath (inside) the fender, insert hex-head screw through fender, support bracket and rear docking point (3). 11. Install washer (7) split lockwasher (5)and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 12. Repeat procedures 1 through 11 for opposite (left-hand) side of the motorcycle. NOTE In time docking points may wear, causing the sideplates to become loose. The fit may be tightened using the following procedure. 1. Loosen docking hardware. 2. Rotate docking points clockwise approximately 45°. 3. Tighten docking hardware to the appropriate torque values. Repeat as often as required, up to 3 times

Incoming search terms:

Incoming search terms: