ecm for 1998 roadking

You search Auto repair manual PDF ecm for 1998 roadking, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ecm for 1998 roadking Direct Download speed 5282 Kb/s

  ecm for 1998 roadking Full Version speed 6162 Kb/s



INSTRUCTIONS FOR PROGRAMMING KEYS INTO RE-FLASHED TOYOTA / LEXUS ECM

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

Download
After we re-flash the ECM it will be in “Automatic Registration Mode” when you install it. The ECM is
expecting that when first powered up (by turning on a key) that it will encounter 3 new keys. The first two keys
are internally (inside the ECM) designated as MASTER keys and the 3rd key inserted will be internally
designated as the VALET key. The ECM can be programmed with as few as 1 key. If less than 3 keys are
programmed into the ECM the security light may flash for some time (hours to weeks) until the ECM “learns”
that it is apparently not going to get any more keys.

Incoming search terms:

2009 Harley Davidson Softail POWER COMMANDER V INPUT ACCESSORY INSTALLATION

0

Filed Under (Harley Davidson) by admin on 26-02-2012

download
1 Remove the seat 2 Uplug the stock wiring harness from the ECM (Fig. A) 3 Remove the 4 nuts that hold the ECM to the bracket and remove the ECM. 4 Remove the bolt that holds the seat strap to the rear fender. 5 Remove the ECM bracket from the fender. Remove one nut at a time or the bracket will fall into the tire. Reinstall the nuts to support the inner fender bracket. Due to the limited amount of room on this bike the seat strap and ECM bracket can NOTbe re-used. 6 Connect the PCVharness in-line of the stock wiring harness and ECM (Fig. B). 7 Place the BLACK PCVto GREYstock connector as close to the fuse box as possible. This connection will NOT lay flat against the frame. 8 Using the supplied velcro secure the ECM to the rear fender. Place the ECM as far down as possible. The upper part of the ECM will just overlap the bolt hole for the seat strap. Make sure to clean both surfaces with the alcohol swab before attaching. If using the Autotune kit offset the ECM about 1″ from center to the right side of the bike. 9 Remove the security module from the top of the battery (Fig. C). This unit slides to the right of the bike.

Incoming search terms:

2001-2003 GL1800/ A ECM Replacement/ Cooling System REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
Install the new ECM, then reinstall the cruise/ reverse control module in the reverse order of removal. NOTE: When you start the vehicle – after completing ALL procedures – the new ECM will require initialization . To initialize the new ECM, perform the following procedure: • Start the bike and allow it to warm up to normal operating temperature and remain at idle for at least 90 seconds . Do not operate the throttle during this time; if you do, the ECU will not initialize properly and the process will need to be repeated. 5. Proceed to the Cylinder Head Inspection section below. Use the Cylinder Head Inspection Kit for the Cylinder Head Inspection procedure. Use the kit for each GL1800/A you inspect. Do NOT dispose of kit items. 1) 19X20 mm cap (2) (cap B) 2) 8X15 mm cap (cap A) 3) Hose plug 4) Bottle/cap w/feed hose 5) Harness clips (10) 6) Harness tape 7) Inspection mirror A limited number of additional Cylinder Head Inspection Kits are available: call TechLine at 800-421-1900, ext. 1 if you need one. Kit contents are NOT available separately as parts. NOTE: • The following late ’03 models do not have to have their cylinder heads inspected: • Perform the following procedure with the engine at room temperature. • Both Left and Right cylinder heads must be inspected. • Use the Cylinder Head Inspection Kit for the following procedure. 1. Remove the front lower fairing. (See S/M, 2-6) 2. Remove and suspend the rear brake reservoir, being careful not to stress the brake hose. (See S/M, 15-A-8) CONNECTOR B (22-GRY) CONNECTOR C (6-BLK) CONNECTOR A (22-BLK) ECM (ENGINE CONTROL MODULE) 1 2 3 4 5 6 7 Late ’03 (Non-ABS): after VIN 1HFSC470*3A204632 Late ’03 (ABS): after VIN 1HFSC474*3A201020 Cylinder Head Inspection Kit Cylinder Head Inspection

Toyota Engine Control Module (ECM) Parts Information

0

Filed Under (Toyota Manuals) by admin on 20-10-2011

download
2005-2008 Corolla Engine(s): 1ZZ Transmission(s): 5MT, 4AT VDS(s): BR30E, BR32E 2005-2008 Matrix Drive Type(s): 2WD Engine(s): 1ZZ Transmission(s): 4AT, 5MT VDS(s): KR30E, KR32E Introduction The purpose of this TSB is to provide the Engine Control Module/ECM (SAE term: Power train Control Module/PCM) parts information necessary for proper identification and vehicle application. A vehicle with an incorrect ECM (PCM) installed may cause one or both of the following conditions: •M.I.L. “ON”DTCP0741-Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL). •Failureto complete On-Board Diagnostic (OBDII) Readiness Monitors. NOTE If the part number is correct, the ECM (PCM) is NOT the cause of the DTC or OBDII Readiness Monitor concern.

Suzuki GSX-R 1000 AFR Tuner INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 20-02-2012

download
The installation of the AFR Tuner should be done by experienced technicians only. Always disconnect the battery from the motorcycle before making any modification to the wiring harness. Remove the negative terminal from the battery before starting the installation work. The quality of the installation work greatly affects the reliability of the AFR Tuner and the motorcycle. Work precisely and very carefully when modifying the wiring harness of the vehicle. Always double check that the wire you are about to cut or tap into is the correct one. The ECM or the AFR Tuner can be destroyed by a faulty installation. 3.2. Installing the AFR Tuner to the wiring harness 3.2.1. Main cable The AFR Tuner connects to the motorcycle through its Main connector . Figure 2 shows the wiring diagram and the necessary modifications, which needs to be made when installing the unit into the fuel injection system of the motorcycle. Information about the ECM terminal numbers and wire colors for some popular motorcycles can be found in Chapter 6 . The best location for installing the AFR Tuner main unit is at the passenger seat area of the motorcycle mounted in the trunk space or on the subframe under the fairing, as this place provides protection from engine heat and the weather. Electrical contact between the metal casing of the AFR Tuner and the rear subframe must be prevented by using insulating material, such as the included self adhesive velcro strips. If necessary use some cable ties to secure the unit in place. The installation of the AFR Tuner into the wiring harness involves tapping into some wires and cutting others while connecting the two ends to the AFR Tuner. The harness modifications are best done near the ECM, since most of the wires can be found there. Part of the wiring modifications are related to connecting the AFR Tuner in-line between the ECM and the fuel injectors. In such cases when the motorcycle is equipped with primary and secondary injectors the AFR Tuner has to be installed on the primary injectors, which operate under all engine conditions. Correct grounding of the AFR Tuner is very important for electrical noise reduction. The above mentioned insulation of the metal case from the motorcycle frame is necessary for the same reason, which is to avoid the forming of a ground loop. An even more important requirement is the correct connection of the three ground wires of the AFR Tuner. As shown on Figure 2 , these three wires must be led out separately to the ECM and connected together at same point where the ECM ground wire is tapped into. This point should be as close to the ECM terminal as possible. For best quality of the electrical contacts all connections should be done by soldering and covering the exposed part of the wire with heat shrink tubing. For reliability reasons do not use clip on type wire taps

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

1998 Honda Shadow Aero Specifications And Review

0

Filed Under (Honda) by admin on 24-11-2010

download
can fix it – let us help. The color combo that would have been featured here, had we not got rained on. As light as the morning precipitation was, a rainsuit seemed silly, and surely jeans and a leather jacket would be enough. However, at the crest of the peninsula, El Nino let his wrath be felt. A full-on downpour of Florida- like proportions dropped from the sky, without the benefit of gulf-stream warmth. Suddenly, wearing geeky-looking Gore-Tex seemed like a very good idea. Riding through six inch deep floodwaters at about 15 mph, the Aero kept a very even keel. The floorboards (first ever on a Honda) kept the feet drier than they would have been otherwise. After a brief stop at a military museum, we headed back to Honda’s HQ for a van ride to lunch at Hollywood’s House of Blues. Detail 101: Witness the huge chrome headlight/speedo assembly, with matching idiot lights set into the triple clamp. We couldn’t form much of a riding impression from our rain-soaked 30 mile jaunt, but we liked what we found. If you’re a big fan of the ACE 750, you’ll be a big fan of the Aero. Although the styling is not ground-breaking, it isn’t a carbon copy of you-know-who (hint: They’re based out of Milwaukee). The detail on the Aero is beautiful, with tasteful chrome accents and well-finished pieces. We hope to get the big 1100 back for a full test against Suzuki’s new Intruder 1500LC, Harley’s new Road King Classic, and all the other cruiser big boys some time this spring, after El Nino goes away … Manufacturer: Honda Model: 1998 Shadow Aero Price (two-tone): $9,995.00 Engine: liquid-cooled 45 degree V-twin, single crank pin Bore and Stroke: 87.5 x 91.4mm Displacement: 1099cc Carburetion: Two 36mm CV Transmission: 5 speed Wheelbase: 66.1 in Seat Height: 28.5 in Fuel Capacity: 4.2 gal with .8 gal reserve Claimed Dry Weight: 623 lbs

Incoming search terms:

1998 BMW R1100RT LCD Temperature Gauge Scale Calibration LCD Fuel Gauge Calibration Fuel Sender Testing and Cleaning

0

Filed Under (BMW) by admin on 26-10-2010

download
Oil Temperature and Gauge 2.1. Introduction My 1998 BMW R1100RT came with an LCD temperature gauge that shows horizontal black bars in a vertical motif, to indicate temperature. This is difficult to interpret at speed (how many bars are exposed?) and does not actually tell me what the oil temperature is. 2.2. Normal Operation The bike seems to run at 5 or six bars under normal conditions. It appears that the oil thermostat for the cooler is set to ’5 bars’. 2.3. Over Heating The LCD panel indicates that 8 bars is the maximum normal operating temperature. It would be useful to know what the actual temperature is. Modern oils have a normal operating temperature of approximately 110 degrees Celsius and will not show any serious degradationii at this temperature. The maximum sustained operating temperature (at the bearing surface) is approximately 130 degrees Celsius for any oil formulated in the past 5 years and some high performance synthetics will not appreciably degrade even at this temperature. However, the degradation curve is a polynomial and degradation will increase rapidly with increasing temperature. According to the oil’s formulation (pure synthetics will show the least increase with temperature), by approximately 160 degrees Celsius (or about 300 degrees Fahrenheit), oil degradation can be up to 10 times faster then at 110 Deg. C. 2.4. Scale To fix the ‘number of bars’ problem, I determined that an overlay with numbers would be the best idea. 2.4.1. Addendum The number scale became too much to maintain. Rather than this, I cut a mm or so wide stripe out of the self sticking stripping meant for the side of a car. Using a red material, I put it through the middle of the fifth bar of both the temperature and fuel display. The stripe is slightly smaller than the thickness of the bar. This allows me to tell when I am at normal operating temperature and when approximately half a tank is used

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE ELECTRONIC FUEL INJECTION (EFI) STAGE 1 KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
Installation NOTE The installation procedure is divided into three parts: 1) Replacing ECM (1996 and earlier models ONLY) 2) Calibrating the ECM 3) Replacing stock air cleaner with air cleaner from kit. 1) REPLACING ECM (1996 and earlier models ONLY) 1. Refer to the REMOVAL/REPLACEMENT section 9C in the 1995-1996 FLT Service Manual, Part No. 99483- 96A. 2. Install ECM in accordance with the installation procedure given in the Service Manual. 2) CALIBRATING THE ECM Have dealer recalibrate the ECM prior to starting vehicle. NOTE The product information (EO) label contained in this kit is required in the state of California only. This label is required to aid in passing the California Smog Check Program. Place the information label on the right side of the frame directly beneath the VIN sticker. Do not place the label over other product information labels. Do not place the label on motorcycles other than those specified in the instruction sheet. 3) REPLACING STOCK AIR CLEANER Removing Stock Air Cleaner NOTE Refer to the applicable Service Manual and check the warm- slow idle speed adjustment before removing stock backplate. 1. Remove stock backplate following the instructions given in the appropriate Service Manual. 2. See Service Parts Illustration. Retain stock air cleaner cover and buttonhead screw and washer. Installing High Performance Air Cleaner 1. See Service Parts Illustration. Locate banjo bolts (10) included with kit. Place one washer (11) over each banjo bolt. Insert bolts through holes in mounting bracket (15). Place a second washer over each bolt. Place manifold breather (16) over bolts with hose fitting toward rear of motorcycle. Install remaining washers over the ends of bolts

1994-1998 HONDA RVF400RR Racing Kit INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
(1)Fuel High Octane white gasoline (2)Engine Oil Recommended Oil: HONDA Ultra-GP (for four-cycle Motorbike) SAE20W-50 or 10W-40
Full Capacity: 3.0Liter (5.28pt) Oil Exchange: 2.5Liter (4.4pt) Filter Exchange: 2.4Liter (4.224pt) (3)Spark Plug NGK R 847-10(11)(4)Cooling Water Highly recommend checking the water level on each ignition/riding. Ingredient: Tapped water or Drinking water I. Unscrew a radiator cap. Apply water up to limb of intake. II. Hold steering and heave the body two or three times to let air out. III.Add water if necessary. IV. Screw the cap tighten.V. Start Engine then check water level again. Add water if necessary. < Notes for racing condition> • Keep your attention when you re-check the water level since the water would spill out of intake. Also cover the body with wastes. • Drain cooling water in a catch-tank before riding. • Drain whole water in a radiator after riding. It avoids corrosion or clog of components. • It is admitted adding coolant in winter season. Handle carefully when you apply them. It makes the circuit slippery if it drops or spilled.

Incoming search terms: