electra glide 2009 probleme compensator

You search Auto repair manual PDF electra glide 2009 probleme compensator, if there are search results will appear below. If search results do not exist, please search by others keyword.



  electra glide 2009 probleme compensator Direct Download speed 5282 Kb/s

  electra glide 2009 probleme compensator Full Version speed 6162 Kb/s



Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

HARLEY DAVIDSON FLHT (Electra Glide Standard) FAIRING COMPARTMENT POUCH INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
General This kit is designed for 1996 and later FLHT, Electra Glide Standard, model motorcycles Kit contents: QTY DESCRIPTION 1 Pouch 4 Velcro™strip Installation 1. Wash inside of fairing compartment with a clean, soft, nonabrasive cloth, water and mild soap. 1 CAUTION DO NOT use benzine, paint thinner, gasoline, powdered abrasives, alkaline cleansers, or any other harsh cleansers to clean the fairing compartment. They will damage the surface. Never scrape fairing surfaces with a razor blade or other sharp instrument because permanent damage will result. 2. Arrange pouch in compartment. 3. Align and attach velcro strips from kit to top, bottom and sides of compartment so they match the placement of velcro strips on pouch. 4. To secure pouch to fairing compartment, press pouch velcro strips against compartment velcro strips. Care of Pouch 1. When necessary, remove and wash pouch with mild soap and warm water

Incoming search terms:

HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

HARLEY DAVIDSON DETACHABLE TOUR-PAK KIT FOR ELECTRA GLIDE CLASSIC INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Install Docking Kits and License Plate Holder 1. Install Rear Detachable Docking kit. Refer to the instruction sheet provided with kit. 2. Install Touring Detachable Tour-Pak Rack. Refer to the instruction sheet provided with kit. 1 4 2 3 is03989 1. License Plate Holder 2. Red Reflector 3. Original Equipment Screws 4. Original Equipment Bottom Support Tube Figure 2. Install License Plate Holder 3. See Figure 2. Install the new license plate holder (1) to the bottom support tube (4) using screws (3) saved from prior step. 4. Remove adhesive backing from red reflector (2) and carefully center and align it with the bottom edge of the license plate holder (1) and press firmly into place. -J03930 1 of 4 MOUNTING ANTENNA RELOCATION BRACKET 1. See Figure 6. Assemble joint assembly (9) to antenna mounting bracket (6) using lock washer (5) and 2 hex nuts (4). Tighten hardware securely. 2 1 5 4 3 is03992 1. Rear Docking Point 2. Docking Point Support Bracket 3. Antenna Mounting Bracket 4. Antenna/Cable Adapter 5. Rear Docking Point Screw and Locknut Figure 3. Relocated Antenna Bracket and Cable 2. See Figure 3. Install assembled antenna bracket (3) by removing screw and locknut (5) securing left rear docking point (1) to docking support (2). Install bracket as shown and reinstall rear docking point screw and locknut. Tighten screw and locknut to 15-19 ft-lbs (20.3-25.7 Nm) . 3. Thread antenna/cable adapter (4) onto joint assembly. ROUTING ANTENNA CABLES 1. See Figure 4. Gently remove left side cover (1) by pulling from frame tubes (no tools required). 2. Connect original antenna cable (not shown) to bottom of joint assembly. 3. Route antenna cable/wiring between left frame rail and fender. 4. See Figure 5. Attach cable to docking point support bracket in location (1) using short cable strap. 5. See Figure 4. Coil excess antenna cable/wiring (2) and use long cable strap (3) to fasten cable to frame under left side cover (1) with vehicle wiring harness. 6. See Figure 6. Cap unused wiring connector with connector housing (10).

Harley-Davidson Electra Glide LED Motorcycle Lightbar Installation Guide

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Mounting IMPORTANT! The lightbar should be located a minimum of 16″ from any radio antennas! This product is designed to mount in the lowest, visable section of the motorcycle windshield. The mounting procedure requires removal of the front facia panel of the motorcycle. 1. Remove the 3 screws along the base of the windshield from the upper section of the faring facia panel. 2. Remove the 4 remaining screws (shown above) that secure the facia panel to the faring. With these screws removed, the facia and windshield can now be removed from the motorcycle faring. 3. Position the lightbar into its mounting position. The base of the lightbar fits onto the three screw bosses used by the screws removed in step 1. 4. With the facia panel removed, the lightbar should now be wired. 5. Route the wires to their respective destinations. It is left to the installation technician’s discretion to select a path for these wires that will both protect them from possible damage and not interfere with the operation of any other vehicle components or equipment. 6. Using the original hardware removed in steps 1 & 2, remount the faring and windshield according to the motorcycle manufacturers service manual

2009 TOYOTA RAV4 DEBUTS NEW FUEL EFFICIENT FOUR CYLINDER ENGINE AND ADDS NEW SAFETY

0

Filed Under (Toyota Manuals) by admin on 01-10-2011

download
Toyota has restyled its popular RAV4 compact sport utility vehicle for 2009. The new standard 2.5-liter four-cylinder engine is more powerful than the previous 2.4-liter engine and is more fuel efficient. In addition, all RAV4 models feature interior upgrades and a comprehensive new Sport Appearance Package is available for the 4WD V6 model. All RAV4 models receive enhanced safety and security features with standard front seat active headrests and an engine immobilizer. Comfort, convenience and user technology are also significantly enhanced in 2009 RAV4 models. The Limited grade adds a new standard Smart Entry system that allows the driver to open the vehicle by simply carrying the key fob and grasping the door handle. The Sport and Limited grades offer an available new rear backup monitor. Integrated satellite radio is newly available for 2009, and the Sport and Limited grades offer a new low-cost navigation system. All RAV4 models gain new standard seat fabric, and the Sport grade exclusively offers a new, unique Charcoal leather option.

Incoming search terms:

RESTYLED 2009 TOYOTA RAV4 DEBUTS NEW FUEL-EFFICIENT FOUR-CYLINDER ENGINE AND ADDS NEW SAFETY, CONVENIENCE AND USER TECHNOLOGY FEATURES

0

Filed Under (Toyota Manuals) by admin on 17-09-2011

Download
Toyota has restyled its popular RAV4 compact sport utility vehicle for 2009. The new standard 2.5-liter four-cylinder engine is more powerful than the previous 2.4-liter engine and is more fuel efficient. In addition, all RAV4 models feature interior upgrades and a comprehensive new Sport Appearance Package is available for the 4WD V6 model. All RAV4 models receive enhanced safety and security features with standard front seat active headrests and an engine immobilizer. Comfort, convenience and user technology are also significantly enhanced in 2009 RAV4 models. The Limited grade adds a new standard Smart Entry system that allows the driver to open the vehicle by simply carrying the key fob and grasping the door handle. The Sport and Limited grades offer an available new rear backup monitor. Integrated satellite radio is newly available for 2009, and the Sport and Limited grades offer a new low-cost navigation system. All RAV4 models gain new standard seat fabric, and the Sport grade exclusively offers a new, unique Charcoal leather option.

Incoming search terms:

HARLEY DAVIDSON ELECTRA-GLO LIGHT POD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTES Clean the controller mounting area and the areas where the light pods will be mounted with soap and water before beginning the installation, and allow to dry thoroughly. Remove debris, dirt and grime from the vehicle areas to be highlighted. Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the light pods and controller box to vehicle surfaces. Light pods should not be located closer than 2.5 inches (63.5 mm) from exhaust pipes or mufflers, and must have 1.5 inches (38.1 mm) clearance from engine cylinders and heads. Do not install light pods with the light source facing directly away from the vehicle. Installation should be done in a way that allows the light to be seen indirectly by reflecting from chrome or painted surfaces of the vehicle. Prepare the Motorcycle To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to disconnect the battery cables, negative (-) cable first. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Locate and Install the Controller NOTE Do not mount the controller box in a location where vehicle suspension travel could result in contact with the ON/OFF switch or dimmer control. Damage to the controller box will occur. 2. See Figure 2. Locate the controller box (10) on a flat surface that will allow the red (+) and black (-) leads to reach the battery terminals and the rider to access the controls (with the vehicle parked) and, if necessary, the in-line fuse holder (A). a. Test-fit the controller box to the selected surface before installation. Do not remove the adhesive backing until ready to attach the controller box. b. Clean the controller box mounting area with one of the included alcohol swabs. Allow to dry thoroughly. c. Remove the liner from the adhesive backing of the controller box. Carefully position the controller box to the surface, and press firmly into place. Hold the controller box in position with steady pressure for about one minute. Connect the Battery Cables NOTE Verify that the ignition/light key switch is in the OFF position before attaching the battery cables. 3. Verify that the ignition/key switch is turned to the OFF position. Apply a light coat of Harley-Davidson electrical contact lubricant (part number 99861-02), petroleum jelly or corrosion retardant material to the battery terminals. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Refer to the owner’s manual and follow the instructions given to install first the vehicle’s positive (+) battery cable then the red (+) light pod controller lead ring terminal to the positive (+) battery terminal. Tighten to owner’s manual specifications. Install first the vehicle’s negative (-) battery cable then the black (-) light pod controller lead ring terminal to the negative (-) battery terminal. Tighten to owner’s manual specifications. Arrange the Electra-Glo Light Pods NOTES Electra-Glo light pods (1) can be installed in a variety of locations. They are best installed on a flat surface to provide indirect lighting illuminating mechanical features, vehicle finish or for ground effects. Refer to the notes at the beginning of the Installation section. 5. Select the area or lines of the motorcycle to highlight, and suitable locations for each light pod. DO NOT permanently affix the light pods at this time. Lightly tape the pods in place temporarily until the desired visual effect is achieved Verify clearance from movement of rubber mounted engine or other moving parts, heat sources, or chafe points

Incoming search terms:

Repair Manual Supplement : Vehicle Pulling to One Side Suspension

0

Filed Under (Toyota Manuals) by admin on 20-10-2011

download
2002-2009 4Runner, Avalon, Camry, Corolla, Highlander, Land Cruiser, Prius, RAV4, Sequoia, Sienna, Solar a, Tacoma, Tundra 2007-2009 Camry HV, FJ Cruiser 2002-2005 Celica, Echo, MR2 Spyder 2006-2009 Highlander HV 2003-2009 Matrix 2009 Venza 2004-2009 Yaris When radial tires are rotating, they have the characteristic of generating force in the lateral direction between the tire and the road surface. This lateral force is comprised of two factors: •Ply-steer, which changes direction according to the rotation direction of the tires. •Conicity, which is generated inafixed direction regardless of the tire rotation direction. If these lateral forces are too strong, vehicle pulling will occur. A. Ply-Steer Lateral force due to ply-steer is produced by the construction of the belts inside the tire tread. With radial tires, the wire of the belt is slanted as shown in the illustration below. Thus, it is in the lateral direction that tire tread easily changes shape (stretches), and lateral force is generated between the tire and the road surface in the lateral direction

Incoming search terms: