email contacts of bajaj companies in china mail

You search Auto repair manual PDF email contacts of bajaj companies in china mail, if there are search results will appear below. If search results do not exist, please search by others keyword.



  email contacts of bajaj companies in china mail Direct Download speed 5282 Kb/s

  email contacts of bajaj companies in china mail Full Version speed 6162 Kb/s



Bajaj Removing And refitting Automatic Cam Chain Tensioner

0

Filed Under (Bajaj) by admin on 31-10-2010

download
1. Remove the 2 Flanged Bolts securing the Tensioner Assembly. 2. Remove Tensioner Assembly from the engine block. 3. Unscrew and remove Lock Bolt. 4. Remove Pushrod, Ball & Retainer, Spring and “O” ring. Clean parts thoroughly and apply grease to the Balls & Retainer. Re-assembly procedure : 1. Place Spring on Pushrod and compress the spring beyond the hole in the Pushrod. 2. Insert a pin or wire into the hole in the Pushrod to hold the Spring in its’ compressed position. 3. Place Balls & Retainer onto Pushrod. 4. Insert Pushrod into the Tensioner body with the small flat on the Pushrod facing, and aligned with, the Locking Bolt hole. 5. Insert the Locking Bolt and tighten it against the small flat on the Pushrod to lock the Pushrod in the compressed position. Remove the pin that’s holding the Spring compressed. 6. Install the Tensioner assembly onto the cylinder block and install and tighten both Flanged Bolts. Be sure that the “O” ring has been installed at the base of the flange. 7.Looosen the Lock Bolt to release the Pushrod, then re-tighten the lock bolt

Incoming search terms:

Toyota Body & Paint Preferred Partner Program

0

Filed Under (Toyota Manuals) by admin on 29-05-2011

Download
That’s why Toyota has created the innovative Body & Paint Preferred Partner Programme. Having tested a wide range of Body & Paint repair products, Toyota has selected a number of companies whose products are of the highest calibre and offer superior results, and who offer reliable, Europe-wide distribution and support. It recommends that all Toyota Authorised Repairers across Europe use products supplied by these companies. They are of course free to choose which supplier they work with from this list of recommendations. Whilst Toyota has negotiated competitive parameters with each partner, exact contract details should be agreed between the partner and the Toyota Authorised Repairer. The programme allows savings made to be reinvested into further improvement of Body & Paint activities

Incoming search terms:

DMCA

0

Filed Under () by admin on 23-05-2017

Digital Millennium Copyright Act (DMCA) Notice

We are in compliance with 17 U.S.C. $ 512 and the Digital Millennium Copyright Act (“DMCA”). It is our policy to respond to any infringement notices and take appropriate actions under the Digital Millennium Copyright Act C’DMCA”) and other applicable intellectual property laws.

If your copyrighted material has been posted on our website or if hyperlinks to your copyrighted material are returned through our search engine and you want this material removed, you must provide a written communication that details the information listed in the following section. Please be aware that you will be liable for damages (including costs and attorneys’ fees) if you misrepresent information listed on our site that is infringing on your copyrights. We suggest that you first contact an attorney for legal assistance on this matter.

The following elements must be included in your copyright infringement claim:

1. Provide evidence of the authorized person to act on behalf of the owner of an exclusive right that is allegedly infringed.
2. Provide sufficient contact information so that we may contact you. You must also include a valid email address.
3. You must identify in sufficient detail the copyrighted work claimed to have been infringed and including at least one search term under which the material appears in our search results.
4. A statement that the complaining party has a good faith belief that use of the material in the manner complained of is not authorized by the copyright owner, its agent, or the law.
5. A statement that the information in the notification is accurate, and under penalty of perjury, that the complaining party is authorized to act on behalf of the owner of an exclusive right that is allegedly infringed.
6. Must be signed by the authorized person to act on behalf of the owner of an exclusive right that is allegedly being infringed.

Send the infringement notice via contact form with “DMCA Complaint” as your subject line otherwise we won’t be able to process your complaint.

Please allow up to a week for an email response. Note that emailing your complaint to other parties such as our Internet Service Provider will not expedite your request and may result in a delayed response due to the complaint not being filed properly.

Incoming search terms:

Harley Davidson BoonDocker Nitrous System Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 2 of 10 This manifold is also designed to vary the float bowl pressure in relation to nitrous pressure, thus keeping the nitrous and fuel delivery in sync. Fluctuations in bottle temperature greatly affect nitrous pressure, which affects nitrous delivery. By automatically adjusting the fuel delivery as nitrous pressure varies, this manifold makes nitrous safe, reliable, and easy to use. Be sure to understand and follow the tuning instructions at the end of these instructions. Proper tuning is an important part of any performance-enhancing product. Part I – Bottle Installation A. Bottle Valve Fittings Insert the 4AN x 1/8″ NPT fitting and the 1/8″ NPT Plug into the bottle valve (these are attached to the lid of the box for the bottle) . Use Teflon tape to seal the threads – be sure not to get tape inside the threads! B. Bottle Mounting Position With nitrous in the bottle, both nitrous liquid and nitrous gas are present under high pressure (760 psi at 70 deg F) . Due to gravity and acceleration forces, the liquid portion of the nitrous will be at the bottom and rearward parts of the bottle. For this nitrous system to work properly, it is important that nitrous liquid be drawn from the bottle. Nitrous vapor will cause a significant decrease in performance. For best results, the bottle should be mounted so the valve is pointed down and towards the back of the vehicle as shown below. ************** *************** ******** ********* *************** (can be installed on top or bottom of air boot) ********** ********* push-button switch (mounts on handlebar) +12 V *********** ************ **** ****** *! “**#$******%* *! “**#$*#*%* 20 deg to 90 Front of motorcycle Rear of motorcycle BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 3 of 10 Bottle mounted inside airbox: For some applications, a small bottle can be mounted inside the airbox as shown. Note: because of the restricted space, it was necessary to mount this bottle at a non-optimal angle (the valve is pointed towards the front instead of the rear)

Incoming search terms:

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

Harley Davidson MC/ MIC HARNESS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2012

download
Use the diagonal cutters and razor blade to cut any tie wraps or harness coverings away from the harness connected to C28. At least 3 ” of wire must be unsheathed. Use a 1/16″ wide blade flat screw driver to push the Ampseal connector wedge lock tabs away from the red wedge lock as shown in Photo 3. Pull the wedge lock up as shown in Photo 4. The wedge lock should never be removed from the housing for insertion or removal of the contacts. Photo 3 – Connector Disassembly Step 1 Photo 4- Connector Disassembly Step 2 Technique for removal of Ampseal contacts from the connector housing (refer to Photos 5 and 6): Grab the wire to be removed with needle nose pliers or hemostats. While rotating the wire back and forth over a half turn (1/4 turn in each direction), gently pull the wire until the contact is removed. Photo 5- Pin Removal, Step 1 Photo 6- Pin Removal, Step 2 End of Removal Technique
3 of 5 Document part number: 65298R2 Installing Kennedy Audio Interface Harness part #85582 Locate Kennedy harness part #85582 and 3 pieces of 1/8″ diameter x 2″ shrink-wrap. The sequence for installing the harness is: Locate and remove the appropriate contact from the Ampseal connector (refer to Figure 1, below). Place a piece of heat shrink over the corresponding mating pin on Kennedy harness #85582. Press the mating pin and the Ampseal connector contact together (See Photos 7 and 8)

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

WAAREE A -1 4 T20W40 OIL 4 stoke Motorcycle Engine Oil

0

Filed Under (Tips and Review) by admin on 16-11-2010

download
APPLICATION •Designed for all high power 4 Stroke Motorcycle & Scooters •Recommended for use in 4 Stroke Motorcycles & Scooters of Hero Honda, Bajaj, TVS, Yamaha, Suzuki, LML & all other makes where OEM is recommending 20w40 Oil. BENEFITS •Excellent heat resistance capability to ensure more power for greater pick up •Excellent Enginecleanliness, outstandingthermal & oxidation stability to help fight deposit formation leading to longer drain intervals and excellent fuel efficiency. •Excellent Valve Train Wear Performance & High Temperature characteristics ensuring longer engine life •Excellent formulation to handle the different requirements of three critical zones of 4 stroke Motorcycle engines , Gear and Clutch. PERFORMANCE STANDARD •API SM*(*VTW ONLY) •JASO-MA2 TYPICAL PRODUCT DATA CHARACTERISTICS WAAREE A1 4T 20W40 KV, cSt @ 1000C 14.80 VI , min 115 Flash Point (COC) c0Min 236 TBN mg KOH/g Min 7.40 Pour Point 0 C Max -21 (These are typical figures and do not constitute a specification

Honda CRF/ TRX 450R Camshaft Installation

0

Filed Under (Honda) by admin on 19-11-2011

download
Break-in of this camshaft is important and you should adhere to all of the following instructions. It is also very important to use plenty of engine assembly lubricant, recommended is Coastal Engine Assembly Lube or Clevite 77, both are available from most automotive supply companies. We recommend you change the engine oil before the initial start-up of the engine after the assembly. Then change the oil again after the break-in of the cams to remove the excess
phosphate from the coated cams. These steps will help ensure that the camshaft breaks-in properly and that you have a long lasting product. Using full synthetic engine oil during break-in is not recommended but, is OK to use after the one-hour break-in period is over. Following a regular maintenance schedule is the best way to ensure durability and performance over the long run. Cleanliness is always a good place to start. Make sure the motorcycle is cleaned thoroughly before you start. It would be advisable to use an engine degreaser on the frame and the engine. Remove the fuel tank and thoroughly clean the inside of the frame rails, around the carburetor, and behind the radiators. Be sure to remove the ignition coil assembly and using high-pressure air, clean the spark plug hole out before the plug is removed. This will ensure a clean engine during the assembly process and less of a chance of thread damage and/or dirt contamination in the engine during reassembly

Incoming search terms: