exhaust actuator valve on 2009 suzuki boulevard 109rt

You search Auto repair manual PDF exhaust actuator valve on 2009 suzuki boulevard 109rt, if there are search results will appear below. If search results do not exist, please search by others keyword.



  exhaust actuator valve on 2009 suzuki boulevard 109rt Direct Download speed 5282 Kb/s

  exhaust actuator valve on 2009 suzuki boulevard 109rt Full Version speed 6162 Kb/s



SUZUKI M109 1800 cc EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 10-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System. 6. Remove the dust cover from the solenoid to expose the rotating cam and cables. DO NOT TRY TO ROTATE THE CAM RELATIVE TO THE ACTUATOR SELENOID TO REMOVE THE CABLES; DOING SO MAY DAMAGE THE INTERNAL COMPONENTS OF THE SOLENOID. To remove the cables from the cam, use the slack in the cables obtained in Step 5 to disengage the cable barrels from the cam, see Figure 1. THE DUST COVER WILL NOT BE REINSTALLED. 7. Now prepare the exhaust valve actuator solenoid for reuse. SECURELY HOLD THE CAM TO PREVENT IT FROM ROTATING IN THE SOLENOID. WHILE PREVENTING THE CAM FROM ROTATING, remove the 10 – 32 flange bolt securing it, see Figure 2. Replace the cam with the Cobra supplied cam, BE SURE TO PREVENT THE CAM FROM ROTATING WHEN REINSTALLING THE BOLT, OTHERWISE DAMAGE MAY OCCUR TO THE SOLENOID , see Figure 3. Torque to factory specifications.

Incoming search terms:

SUZUKI M109 1800 cc FRONT/REAR EXHAUST / HEATSHIELD INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set collar and grommet aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve actuator solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System

1998 YAMAHA YZF-R6 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
Camshafts Drive system Camshaft cap inside diameter Camshaft journal diameter Camshaft-journal-to-camshaftcap clearance Intake camshaft lobe dimensions Measurement A Measurement B Measurement C Exhaust camshaft lobe dimensions Measurement A Measurement B Measurement C Max. camshaft runout Chain drive (right) 23.000 23.021 mm 22.967 22.980 mm 0.020 0.054 mm 33.05 33.15 mm 25.14 25.24 mm 7.81 8.01 mm 32.55 32.65 mm 25.07 25.17 mm 7.38 7.58 mm 0.08 mm 33.0 mm 25.09 mm 32.50 mm 25.02 mm 0.06 mm
2-5 ENGINE SPECIFICATIONS SPEC Head Diameter Face Width Seat Width Margin Thickness Item Standard Limit Timing chain Model/number of links Tensioning system RH2015/120 Automatic Valves, valve seats, valve guides Valve clearance (cold) Intake Exhaust Valve dimensions 0.11 0.20 mm 0.21 0.30 mm Valve head diameter A Intake Exhaust Valve face width B Intake Exhaust Valve seat width C Intake Exhaust Valve margin thickness D Intake Exhaust Valve stem diameter Intake Exhaust Valve guide inside diameter Intake Exhaust Valve-stem-to-valve-guide clearance Intake Exhaust Valve stem runout Valve seat width Intake Exhaust 24.9 25.1 mm 21.9 22.1 mm 1.14 1.98 mm 1.14 1.98 mm 0.9 1.1 mm 0.9 1.1 mm 0.6 0.8 mm 0.6 0.8 mm 3.975 3.990 mm 3.960 3.975 mm 4.000 4.012 mm 4.000 4.012 mm 0.010 0.037 mm 0.025 0.052 mm 0.9 1.1 mm 0.9 1.1 mm 1.6 mm 1.6 mm 0.5 mm 0.5 mm 3.950 mm 3.935 mm 4.042 mm 4.042 mm 0.08 mm 0.1 mm 0.04 mm 1.6 mm 1.6 mm
2-6 ENGINE SPECIFICATIONS SPEC Item Standard Limit Valve springs Free length Intake (inner) (outer) Exhaust Installed length (valve closed) Intake (inner) (outer) Exhaust Compressed spring force (installed) Intake (inner) (outer) Exhaust Spring tilt Intake (inner) (outer) Exhaust Winding direction (top view) Intake Exhaust 37.0 mm 38.4 mm 41.7 mm 30.0 mm 32.5 mm 36.1 mm 69 79 N (7.0 8.0 kgf) 114 132 N (11.6 13.4 kgf) 160 184 N (16.3 18.7 kgf) Clockwise Clockwise 35 mm 36.5 mm 39.5 mm 2.5/1.6 mm 2.5/1.7 mm 2.5/1.8 mm Cylinders Cylinder arrangement Bore stroke Compression ratio Bore Max. taper Max. out-of-round Forward-inclined, parallel 4-cylinder 65.5 45.5 mm 12.4 : 1 65.50 65.51 mm 0.05 mm 0.05 mm

Incoming search terms:

TVS – 811 Series Trap Valve Station Installation, Operation and Maintenance Instructions

0

Filed Under (TVS) by admin on 29-04-2012

download
In a piston valve, the control of stem and seat leakage is obtained by tightness of the valve sealing rings to the body and valve plug. The bonnet compresses the valve sealing rings against the body and the valve plug. Flexible disc springs automatically assure a tight seal by exerting pressure on the valve sealing rings, keeping them compressed. Opening and Closing the TVS Isolation Valves The isolation valve begins to stop flow when the valve plug enters the lower valve sealing ring. When the isolation valve is completely closed, the valve plug is in contact with the full height of the valve sealing rings, ensuring the best possible seal. In fact, there is no advantage to be gained in torqueing the valve closed. Armstrong recommends that after closing the isolation valves completely, the handwheel should be turned back one half turn. This makes it easy to re-open the valve by avoiding metal to metal seizure. Troubleshooting – Isolation Valves A piston valve will retain its leak tightness for several years without maintenance. In severe service, such as rapid heating and cooling, some field maintenance may be required. Depending on the problem, these simple steps may help: ! ! ! ! ! Isolation Valve leaks, when the valve is closed . First, Check to make sure the valve is actually closed . Check to see if bonnet is seated on the body, if not, tighten the bonnet nuts until the bonnet seats. This recompresses the valve sealing rings against the body and the valve plug. If valve continues to leak, replace the isolation valve assembly

Incoming search terms:

CYLINDER HEAD REPAIR MANUAL

0

Filed Under (Tips and Review) by admin on 28-10-2010

download
ADJUSTABLE CYLINDER HEAD STAND Head can be rotated 360 degrees. Stays in any position using a simple locking mechanism. Use on twin or four cylinder heads. Shipping weight: 14 lbs. Adjustable length-10-1/2″ to 20-1/2″ long x 14″ width x 10-3/4″ high. 35-8602 Cylinder Head Stand VALVE GUIDE DRIVERS Use for removal and installation of valve guides into cylinder head. Available in the following sizes: 35-8418 4.5mm YM-4116 35-8416 6mm YM-4064-A 35-8417 5mm YM-4097 35-8414 7mm YM-1225-A 35-8408 5.5mm YM-1122 35-8413 8mm YM-1200 VALVE GUIDE DRIVER SET (REMOVE & REPLACE) Designed for speed and accuracy, this eleven piece set provides the right tool for the job. Driver set includes two valve guide drivers (5.5mm and 6.6mm), four valve guide installers, one cutter, three cutter pilots (5.5mm, 6.6mm, and 7.7mm) and one tap handle extension bar. 35-9445 Valve Guide Driver Set YAMAHA VALVE GUIDE INSTALLERS These installers are used for installation of Yamaha shoulder less valve guides to a specific depth into the cylinder head. To use, position onto the valve guide and drive into the cylinder head until installer makes contact with cylinder head surface. Note: Must use with Valve Guide Driver. Available in the following sizes: 35-8439 4.5mm YM-4117 35-8437 5.0mm YM-4098 35-8419 5.5mm YM-4015 35-8435 6mm YM-4065-A 35-8423 7mm YM-4017 VALVE GUIDE REAMERS Reaming valve guides after installation assures a proper valve stem to valve guide fit. Available in the following sizes: 35-3829 4.5mm YM-4118 35-3851 7mm YM-1227 35-3836 5.5mm YM-1196 35-3852 8mm YM-1211 35-3847 6mm YM-4066 CLOVER VALVE LAPPING COMPOUND KIT The world famous green can with the four leaf clover. For seating valves, mating gears, and sharpening. Sold as a kit with coarse 120 grit (roughing) and 280 fine grit (finishing). 35-0309 Clover Valve Lapping Compound VALVE LAPPING TOOL The ultimate vacuum stick for insuring perfect surfaces on valves and valve seats. Interchangeable cups make unit suitable for use with virtually any size valve. Set includes vacuum stick, 3/4″ and 1/4″ diameter rubber cups. 35-8998 Valve Lapping Too

Incoming search terms:

2003 SUZUKI SV 650 FUEL SYSTEM AND THROTTLE BODY SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FUEL PUMP The electric fuel pump is mounted at the bottom of the fuel tank, which consists of the armature, magnet, impeller, brush, check valve and relief valve . The ECM controls its ON/OFF operation as controlled under the FUEL PUMP CONTROL SYSTEM . When electrical energy is supplied to the fuel pump, the motor in the pump runs and together with the impel- ler . This causes a pressure difference to occur on both sides of the impeller as there are many grooves around it . Then the fuel is drawn through the inlet port, and with its pressure increased, it is discharged through the outlet port . The fuel pump has a check valve to keep some pressure in the fuel feed hose even when the fuel pump is stopped . Also, the relief valve is equipped in the fuel pump, which releases pressurized fuel to the fuel tank when the outlet of the fuel pressure has increased up to 450 -600 kPa (4.5- 6.0 kgf/cm2,64- 85 psi) . Relief valve Brush , ∎ I,’ Check valve Magnet L Armature When the impeller is driven by the motor, pressure differential occurs between the front part and the rear part of the blade groove as viewed in angular direction due to fluid friction . This process continuously takes place causing fuel pressure to be built up . The pressurized fuel is then let out from the pump chamber and discharged through the motor section and the check valve . FUEL SYSTEM AND THROTTLE BODY 5- 3 Inlet port I I Impeller 5-4 FUEL SYSTEM AND THROTTLE BODY FUEL PRESSURE REGULATOR The fuel pressure regulator consists of the spring and valve . It keeps absolute fuel pressure of 300 kPa (3.0 kgf/cm2,43 psi) to be applied to the injector at all times . When the fuel pressure rises more than 300 kPa (3 .0 kgf/cm2, 43 psi), the fuel pushes the valve in the regulator open and excess fuel returns to the fuel tank . 90 Spring 02 Valve FUEL INJECTOR The fuel injector consists of the solenoid coil, plunger, needle valve and filter . It is an electromagnetic type injection nozzle which injects fuel in the throttle body according to the signal from the ECM. When the solenoid coil of the injector is energized by the ECM, it becomes an electromagnet and attracts the plunger. At the same time, the needle valve incorporated with the plunger opens and the injector which is under the fuel pressure injects fuel in conic dispersion . As the lift stroke of the needle valve of the injector is set constant, the volume of the fuel injected at one time is determined by the length of time during which the solenoid coil is energized (injection time)

Incoming search terms:

YAMAHA ROADLINER 1854cc exhaust system Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1. Loosen and move the right side floorboard out of the way to ease installation of the exhaust. 2. Perform the following to remove the stock exhaust system. NOTE : You must disconnect and remove the power valve cables as well as unplug the oxygen sensor connector first, then remove the exhaust system and mounting bracket, see Figure 1 for power valve. Loosening the jam nuts on each cable, and disengaging the cable barrels from the power valve pulley disconnect the power valve cables. The power valve, and cables are not needed with the new Cobra exhaust system, leave the solenoid box under the seat in place without the cables. To disconnect the O 2 sensor remove the right rear footpeg and remove the steel plate with hook securing O 2 sensor harness behind it, retain plate for later reinstallation. Remove the socket head screw securing the O 2 sensor harness and bracket to engine case on the right side of the motorcycle, see Figure 2 , unplug the stock male and female connectors, and remove entire exhaust system. Disengage the female O 2 connector from the small bracket, (which was unbolted from engine case), to gain extra harness length, upon reassembly of new Cobra exhaust, the small bracket, (from engine case), will not be reused, unless a closed loop Fi2000 ® (92-1773CL /92-1773CL-50), is to be used, then please refer to those specific instructions. Next remove the oxygen sensor from the stock exhaust and retain for later reinstallation. 3. Install new exhaust-mounting bracket using the stock M10 bolts; tighten to factory specifications, Figure 3. 4. Install the front and rear headpipes on to the motorcycle using the supplied flanges, stock bolts and nuts. NOTE: On the rear headpipe be sure to install the stock flange cover as shown in Figure 4. Make sure the pipes are parallel to each other. DO NOT TIGHTEN. 5. Remove the muffler assembly from the box and slide two supplied 27-61MSC clamps onto the muffler inlets, refer to Figure 5 for alignment. Do not install oxygen sensor at this time, as it will not clear the frame rail during installation of the muffler assembly. 6. Slide the muffler assembly on to the headpipes by tapping on the headpipes by hand as you push the muffler forward making sure the assembly slides as far forward as possible. Secure the muffler assembly to the mounting bracket using the supplied 5/16-18 bolts but DO NOT TIGHTEN. Install the oxygen sensor at this time, by inserting it between the right frame rail, and engine case, tighten securely once installed. 7. Reconnect the oxygen sensor connectors, then reposition behind the frame rail and reinstall the M6 x 50 mm bolt removed from engine case and tighten to proper factory torque specification.

Yamaha YZF-R1 and R6 TiForce slip on exhaust system REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-01-2012

download
1. Remove the fairing lowers. 2. For R1 owners, please remove the existing exhaust system from the EXUP valve rearward (EXUP valve is retained) and set aside. Save the stock exhaust clamp for reuse. For R6 owners, please disconnect the stock S-bend from the rear of the collector and set aside. Save the stock exhaust clamp for reuse (new clamp provided). Save the stock end can mounting bolt for reuse as well. 3. R1 owners only -Inspect the exhaust gasket. Replace if necessary (gasket provided). 4. For R1 owners -Install the S-Bend to the rear of the EXUP valve, make sure the system fits flush. Reuse the stock exhaust clamp to connect the S-bend to the valve. For R6 owners -Install the TiForce S-bend to the rear of the stock head pipes and collector. Make sure the system fits flush and snug. Reuse the stock exhaust clamp or the provided clamp and loosely attach for now. 5. Install the TiForce end can to the S-bend tail pipe. 6. Loosely attach the two rubber bands, stainless steel bands (K), and stay to the end can using the supplied 6mm hardware (H) and the hanger / stay arm (G). See figure 1 for the assembly procedure. 7. R1 owners -Place the bands approximately 180mm from the edge of the end can. See figure 2. R6 owners -Place the bands approximately 195mm from the edge of the end can. See figure 2. 8. R1 owners -Using the stock provided mounting point on the passenger footpeg, use the M10x45mm bolt and hardware to mount the end can loosely, allowing for some adjustment. 9. Carefully align the two stainless bands so that theyare parallel to each other, and spaced properly on the can. Tighten the 6mm hardware (H). Make sure that the rubber pads fully cover the bands (K). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 10. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire TiForce exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 11. Attach the supplied springs to secure the end can to the S-bend pipe using a spring installation tool if available. Make sure the exhaust system is free and clear of the bike. If necessary, adjust for proper clearance. 12. Go back and tighten all fasteners. 13. Check that all fasteners are tightened per specifications, then start the motor and check for exhaust leaks. 14. Reinstall the fairing lowers.

Incoming search terms:

BMW K1200 RS/ GT Full Exhaust System Full Exhaust System Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Remove the lower fairing. 3. Unscrew the O 2 sensor. Remove the stock exhaust system at the rear canister support bracket and where it bolts to the engine. CAUTION -the stock exhaust is very heavy, be careful not to drop it! Also, be careful not to damage the engine sensor located near the front header pipe. 4. Pry out the old exhaust port gaskets and replace with new BMW OE (x4) exhaust port gaskets. Adab of grease will help hold the gaskets in place while you work. 5. Coat the exhaust studs and O 2 sensor threads with high temperature anti-seize compound. 6. Install the TBR headers into the exhaust ports making sure to get a good seat onto the exhaust port gaskets. Next, install the header nuts starting at the rear/outside stud and working your way forward on the outside set of studs. Once that is finished repeat along the inside set of studs. Tighten header nuts only finger tight at this point. 7. Be sure to coat the threads of the sensor with the included packet of hi-temp anti-seize. Install the O 2 sensor into the TBR headers. Turning the sensor in the counterclockwise direction a few times then screwing it clockwise to install will help make it easier to install and prevent the wire from binding. 8. Place a bead of the hi-temp sealant on the outside edge of the headers that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 9. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) Attach it to the canister support bracket using the stock BMWhardware. Both tabs of the canister clamp should be located on the inside of the canister support bracket. Leave loose for the moment. 10. Make sure everything is lined up and start to evenly tighten up the header nuts to BMWfactory torque specification. Tighten the canister support hardware and install the springs as well. 11. Start the bike and check for leaks around the exhaust ports and the header/canister junction. 12. Reinstall the lower fairing

Incoming search terms:

2007 Yamaha V-Star 1300 Classic Straights Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Stock Exhaust System Removal 1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install Nut strip into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 8. Install Nut strip into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks. NOTE: To achieve optimum performance from your Hard-Krome exhaust system we suggest installing the Dynojet jet kit for carbureted models

Incoming search terms:

Incoming search terms: