exporters and importers of sport wears and equipments mail

You search Auto repair manual PDF exporters and importers of sport wears and equipments mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





Victory V92SC Sport Cruiser COMFORT SPORT HANDLEBAR REMOVAL AND INSTALLATION

0

Filed Under (Victory) by admin on 13-11-2010

download
1. Remove wiring harness dart clips. 2. Disconnect clutch switch connector. 3. Remove 2screwsforclutch lever bracket clamp, remove clutch lever bracket from handlebar. 4. Remove screws for left handlebar switch assembly. Disconnect fast idle cable from lever. Remove switch assembly. 5. Grasp left grip end firmly. While twisting grip end back&forth, pull grip end off and discard. 6. Remove left grip by insertingathin screwdriver between the grip and handlebar end. Spray as mall amount of water/soap solution into the area between the grip and handlebar end. Aggressively twist the grip back-and-forth while simultaneously pulling the grip off. 1. Locate accessory handlebar. 2. Clean inside of throttle grip assembly and throttle cable flange grooves. Ill. 1. 3. Clean throttle grip area. Ill. 1. 4. Slide throttle assembly onto right handlebar end (cableshavenot been removed and should still be attached to the throttle tube). 5. Position the handlebar over the top of the triple clamp and reinstall using bolts removed instep 10. of handlebar removal. Torque to 30 ft. lbs. 6. Install right handlebar switch housing onto handlebar. NOTE: Make sure that locating pin of switch assembly aligns with hole in handlebars. 7. Install right handlebar switch housing screws, make sure locating pin properly aligns with hole in handlebar. Tighten screws to specified torque. 8. Install master cylinder and clamp, install screws. 9. Torque screws to specification. 10. Connect front brake switch wiring harness. 11. Install fast idle cable onto fast idle lever. 12. Clean inside of left grip and handlebar grip surfaces

MPS Sport Bike Auto Shift Installation Manuals

0

Filed Under (Suzuki) by admin on 21-02-2012

download
The first thing to do is remove the seat, fuel tank, and possibly the front fairing if equipped. You will need plenty of room to work. Electrical Connections – You will need to locate and test a few things on your bike before you start wiring. A good ground, an ignition switched 12 volt power source, the horns, and the ignition coils. We have plug n play style harnesses available for some bikes. Check the web site for specific models. Control Box Wiring Coils – Most four cylinder motorcycles use either a individual firing system or a waste spark system. Waste spark is by far the most common. All four cylinder bikes with only two coils use a waste spark system. Most late model four cylinder sport bikes use waste spark systems even though they have four individual coils. Bikes with a waste spark systems will need the 360 calibrated unit. The 360 calibrated Sport Bike Autoshifts are identified by the 360 engraved into the box below the wire lead exit. The P/N for these boxes has the 360 as a suffix. (P/N 1-0299-360) Some of the newest fuel injected bikes (Hayabusa, GSXR1000, ZX12) that have cam sync sensors are individual firing. These bikes will require 720 calibration and will have no outside identifiers and the P/N 1-0299. The Sport Bike Auto Shift has four brown wire leads that are connected to the negative of each individual coil on a four coil system. You will notice that the connector for the four brown wires has a molded in ridge that marks the brown wire that is used as the rpm sensor. This must be connected to the number one cylinder coil negative wire.

Incoming search terms:

HONDA VFR800, CBR1100XX Blackbird, ST 1300 Sport Brake Lever Part INSTALLATION

0

Filed Under (Honda) by admin on 02-11-2011

download
Congratulations on your purchase of an ASV C/5 Sport Streetbike lever. The correct installation of control
levers on a sport/street motorcycle is critical. Incorrect installation or the installation of an incorrect part
can result in a malfunction of your clutch and / or front brake system. This lever should be installed by a
certified mechanic; preferably at your local motorcycle dealer service dept. ASV Inventions, Inc. accepts no
liability for malfunctions as a result of incorrect installation or the installation of a part that was not
designed specifically for your motorcycle. Please check the list below to confirm that the correct year, make
and model of your motorcycle is listed. If the correct year, make and model of your motorcycle is not listed
below, then this part is not the correct part for your motorcycle and must not be installed onto your
motorcycle. ASV C/5 Sport front brake lever part number: BRC541 fits only the following motorcycles:
Please disregard any dashes or letters after this part number that are listed on the part number label of
this box that your lever came in, (ex; BRC541-SK) Any dashes or letters following your part number are for
colors and/or length of the lever and do not affect the application of the lever to the bike.

HONDA GL1800 CHROME SPORT SHIFTER INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
1. Place bike on center stand. 2. Remove the two bolts that hold the stock foot pegs and remove foot peg. 3. Install shifter slot over shifter peg. 4. With the longer bolts supplied, sandwich the Sport Shifter plate between the peg and frame. 5. Screw in bolts and secure tightly. Double check tightness per service manual. 6. Install shifter pegs with hardware provided MOUNTING INSTRUCTIONS FOR 45-1620 GL1800 CHROME SPORT SHIFTER

Moto Guzzi Sport 1100i Owners Manual

0

Filed Under (Moto Guzzi) by admin on 29-11-2010

download
General features Identification data Instruments and controls Riding your motorcycle Break-in Maintenance and adjustments Wheel removal Service schedule Cleaning – Storing Cleaning the windscreen Lubrication Valve gear WEBER injectionignition system (I.A.W.) Electrical equipment Wiring diagram Illustrations Lubrication Pressure fed by gear pump. Oil filters: wire mesh inside sump and replaceable cartridge filter outside sump. Normal lubrication pressure 3.8Ö 4.2 [5] kg/cm2, pressure valve, thermostat and cooler. Low oil pressure sensor (electrical) on crankcase. Generator/Alternator On front of crankshaft (1 4V – 25A). Ignition “WEBER MARELLI” electronic digital induced discharge, with high efficiency coil. Spark plugs: Spark plug gap: 0,7 mm. SPORT 1100 DAYTONA R NGK BPR 6 ESI NGK DR9 E IMS Starting Electric starter (12V-1,2 kW) with solenoid engagement. Ring gear bolted on flywheel. Starter button (START) on right of handlebars. Driveline data Clutch Twin driven plates, dry type, on flywheel. Hand controlled by lever on left of handlebars. Primary drive By gears. Ratio: 1 to 1.3529 (tooth ratio 17/23). Gearbox 5-speed, with constantly meshed gears with front dog clutch. Incorporated cush drive. Pedal operated on the left side of the motorcycle. Gear ratios: Low gear = 1 to 1,812 (tooth ratio 16/29) 2nd gear = 1 to 1,250 (tooth ratio 20/25) 3rd gear = 1 to 1 (tooth ratio 23/23) 4th gear = 1 to 0,833 (tooth ratio 24/20) 5th gear = 1 to 0,730 (tooth ratio 26/19) Ratio: 1:4,125 (tooth ratio 8/33) Overall gear ratios (Engine-wheel): Low gear = 1 to 10,1150 2nd gear = 1 to 6,9761 3rd gear = I to 5,5809 4th gear = 1 to 4,6507 5th gear = 1 to 4,0783 Frame Rectangular section single-beam in NiCrMo steel. Semisupporting engine base. Suspensions Front: White Power upside-down hydraulic telescopic fork with individually adjustable rebound and compression; Rear: steel swing arm with oval cross section. Single shock absorber White Power with separate adjustment of spring preload and of hydraulic rebound and compression damping. Wheels Light alloy castings with 3 hollow spokes (rear wheel with cush drive unit). Rim sizes: – front: 3,50x 17 MT H2 – rear: 4,50×17 MT H2 Tires -front: 120/70 ZR 17 – rear: 160/70 ZR 17 [160/60 ZR 17] Type: Tubeless Front: two Brembo drilled semi-floating disc brakes in stainless steel for SPORT I 100; [two Brembo drilled floating discs, Racing type for DAYTONA RS] with fixed 4 differential piston calipers. Adjustable manual control lever on the right side of the handle-bar; – disc 320 mm;

Incoming search terms:

Ducati Sport Clutch Lever INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 26-10-2010

download
1 To remove your stock lever, use a 19mm wrench or (adjustable wrench) to remove the large sheet metal nut attached to the main pivot bolt that holds the lever. (Photo 1a) Once the locknut is removed, push the main pivot bolt out with your finger or if necessary tap lightly with a rubber mallet or plastic handle end of a screwdriver (Photo 1b) After the pivot bolt is removed, the lever will detach from the master cylinder. (Photo 1c) 1a See other side for further instructions INSTALLATION INSTRUCTIONS FOR PART # CRC552 ® C/5 Sport Clutch Lever Part # CRC552 1b 1c INSTRUCTIONS_CRC552 12/27/07 10:05 AM 23 4 2 Included with your ASV lever is a plastic bag that contains a custom pivot bolt, spacer & locknut. These parts will replace the OEM Brembo parts that were used with your stock lever. 3 Carefully place the lever into the master cylinder while aligning the plunger rod into the plunger cup on your ASV lever as shown in photo 3. 4 Align the lever and the master cylinder pivot bolt holes and Install the main pivot bolt, you will need to pre-load the lever into the master cylinder to get the bolt through the holes. The bolt head has two cut outs on the sides that need to be aligned with the matching area on the master cylinder. Be sure the head of the bolt seats down into the slotted area of the master cylinder. It may be necessary to use a rubber mallet or Plastic end of a screwdriver (Photo 4) to tap the head of the bolt down into its slot. 5 On the other side of the pivot bolt where the threads are, you will see that there is space around the pivot bolt. You will need to install the aluminum spacer that was supplied in the plastic bag with the pivot bolt and locknut. The spacer has a small flange on one side. The flange should be on the outer side when installing it into the hole surrounding the bolt. (Photo 5a) You may need to use pressure to seat the spacer fully into the hole surrounding the pivot bolt. You should be able to do this by using your fingers or thumbs as shown in photo 5b.

Ducati Sport Classic License Plate Bracket Installation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
1. Remove the original fender assembly, it is held on by four M6 bolts. Disconnect the tail light harness connector. 2. Remove the tail light assembly from the fender. Take off the brake light lens by removing two screws on the sides of the unit and switch the turn signal connectors inside as shown. Reinstall the lens. 3. Assemble the base plate, bracket, and tail light as shown. Use hardware provided with the kit. It may be useful to put pieces of tape over the M6x30 bolt heads to temporarily keep them in place. Ducati Sport Classic License Plate Bracket Installation 4. Install the complete assembly on the bike. This may require a bit of patience with the four bolts. Start the locknuts onto the bolts by hand, then push the whole assembly forward and tighten. 5. Reconnect the harness connector. 6. After the installation is complete, it is strongly recommended that the rear spring preload be set to 1″ static sag (stock settings are too soft)

Suzuki DRZ 400K Dual Sport Kit Installation Manual

0

Filed Under (Suzuki) by admin on 11-02-2012

download
DRZ 400 (Kick Start) Dual Sport Kit Installation Manual 1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the side panels, seat, and gas tank. 3. Unplug the headlight from the stock wiring and remove. 4. Unplug the kill button from the stock wiring and remove (Photo 2). The connector is a gray two-conductor connector located under the fuel tank. Release detent on connector to separate. Kill switch connector Photo 2 5. Unplug the stock taillight and remove. Using a utility knife, trim the taillight mounting tabs flush with the underside of the fender. ¼” Photo 3 Countersunk screw and bezel, 4 Places 6. Taillight Installation Position the taillight assembly so that the edge of the red taillight extends past the edge of the fender about 1/4″ as shown in Photo 3. With the taillight positioned as shown Photos 3 & 4 , transfer the four mounting hole locations into the bottom of the fender. Drill the mounting holes at 1/4″ diameter. Use the 6 x 16 mm counter-sunk fasteners and bezels for mounting the taillight

2000-2003 KTM MXC / EXC Dual Sport Kit Installation And Removal Manual

0

Filed Under (KTM) by admin on 08-02-2012

download
00-’03 KTM 400/450/520/525 EXC & MXC Dual Sport Kit Installation Manual 1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, fuel tank, and side panels. Stock switch Bracket Photo 2 EXC – Unplug and remove the stock headlight. (Photo 2.) Unplug the stock three-pin taillight connector and pull the taillight wires back to the rear of the airbox temporarily. MXC – Remove the stock front number plate. 3. Make sure the stock battery is oriented in its mounting bracket as shown with the positive terminal on the left side of the bike (as viewed if sitting on the bike). If not, remove and spin it 180 degrees. Photo 3
4. MXC ONLY! (EXC skip this step.) Locate the stock lighting wiring harness zip-tied under the frame back-bone (See Photo 4). Remove the securing zip-ties and route this wiring forward to the area behind the headlight. Route along right side of frame using factory wire- guide clamp. 5. Brake Light Switch Installation: The KTM kit uses a hydraulic brake-switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the stock banjo bolt and replace with the hydraulic switch as shown. Make sure to install

HONDA XR 100 Dual Sport Kit Installation Manual

0

Filed Under (Honda) by admin on 09-11-2011

download
installation of a Baja Designs Dual Sport kit by itself does not make an off-road motorcycle street legal. Each state has different equipment requirements for street legal motorcycles, including but not limited to such items as DOT approved tires, left and right side mirrors, speedometers, quiet exhaust, chain guards, and side reflectors. Contact your state’s department of motor vehicles or highway patrol for a comprehensive list of equipment that is required for street motorcycles before riding your bike on the street