fat boy lo bagger kits

You search Auto repair manual PDF fat boy lo bagger kits, if there are search results will appear below. If search results do not exist, please search by others keyword.



  fat boy lo bagger kits Direct Download speed 5282 Kb/s

  fat boy lo bagger kits Full Version speed 6162 Kb/s



HARLEY DAVIDSON SLOTTED 6-SPOKE FRONT WHEEL KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to FRONT WHEEL in Service Manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. For FXSTD Models: Discard tapered spacer. 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43918-07 and 43919-07: • The side of the wheel with the valve stem and directional arrow is the right side of the wheel. • The left side of the wheel is the primary bearing side. For Kits 43920-08 and 43921-08: • The left side of the wheel has a machined groove in the hub face to identify it as the primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44055-07, 44056-07, 44057-07, 44058-07, 43538-09, 43549-09 and 43577-09: • The wheel should be installed so that the hub markings are on the left side of the motorcycle. An arrow cast into the rim of Kits 44055-07, and 44056-07 indicates the direction of rotation. A groove is machined in the left-side hub face to indicate the primary bearing side. • For dual brake disc models, install the brake disc according to the Service Manual. The chrome hub cap (2) is not used. • For single brake disc models, install the brake disc according to the Service Manual. The chrome hub cap MAINTENANCE AND CLEANING Chrome parts must be maintained regularly so they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner applied with the Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant.

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

HARLEY DAVIDSON SKULL FOOT BOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Kit 50704-04 is an Operator Footboard Insert Kit. •This kit fits all 2004 and later FLHRS/I (Road King® Custom) model motorcycles. •This kitalso fits 1986 and later FLHR/I/CI, FLHT/C/CI/CUI and FLTR/I models equipped with Swept-Wing footboard pans 50683-04 (right) and 50688-04 (left) . Kit 50704-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50705-04 1Operator footboard insert (left) 50706-04 Kit 50707-04 is a Passenger Footboard Insert Kit. •This kitfits 2004 FLHTCSE models, and all 1986 and later Touring model motorcycles equipped with Swept- Wing Grooved Passenger Footboard Kit 50357-04 . Kit 50707-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50708-04 1 Passenger footboard insert (left) 50709-04 Kit 50710-04 is an Operator Footboard Insert Kit. •This kitfits all 1980 and later Touring models except FLHRS, and 1986 and later FL Softail®model motorcy- cles equipped with footboard pans 50621-79A. Kit 50710-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50711-04 1Operator footboard insert (left) 50712-04 Kit 50713-04 is a Passenger Footboard Insert Kit. •This kit fits all 1986 and later Touring models . •This kit also fits 1986 and later FL Softail models when equipped with accessory passenger footboard kits (Part Number 50602-89B, 50955-97A, 50955-00 or 50602-00). • This kit iscompatible with Chrome Passenger Footboard Cover Kits (Part Numbers 50782-91, 50193-96, 50194-96 and 50246-00). • This kit is notcompatible with Leather Passenger Footboard Fringe Kits (Part Numbers 50947-98 or 50956-98). Kit 50713-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50714-04 1 Passenger footboard insert (left) 50715-04 Installation, Kit 50704-04 (For Swept-Wing Operator Footboards): Removing Previously Installed Inserts 1. Apply liquid dishwashing soap to the rubber beads protruding through the bottom of the footboard pan. 2. With the operator footboard in the “up” position, use a screwdriver to work the rubber footboard beads out through the top of the footboard. 3. Repeat the above steps for the remaining footboard insert. Installing the New Inserts 4. Apply liquid dishwashing soap to the rubber beads on the new footboard insert. 5. Place the footboard insert into position on the footboard pan. From the underside of the footboard, use a pliers to pull each rubber bead into its mating hole in the footboard pan until the beads protrude through the pan. 6. Repeat the above steps for the remaining footboard insert.

Incoming search terms:

Harley- Davidson Bagger Audio factory service manual for removal

0

Filed Under (Harley Davidson) by admin on 03-04-2012

download
POWER & SPEAKER HARNESS INSTALLATION- (Read electrical connections prior to connecting center power and ground wires) 1. Disconnect battery (negative cable first!) 2. Remove outer faring cover 3. Route long speaker wires from fairing area through tank channel to seat area. 4. Route one pair of speaker wires under each fender strut support; purple and purple and black wires to the right and green and green and black wires to the left. AMPLIFIER INSTALLATION- 1. Factory installed electronics will determine suggested placement of amplifier. 2. Position and attach amplifier to outer fairing support bars with supplied wire ties. (Electra/Ultra/Street Glide) BAGGER AUDIO™ LIDS INSTALLATION- Detach factory lid by removing the 2 screws holding the factory strap to inner lid and 5 small torque screws holding lid to factory latch assembly. (Consult factory service manual for further instructions) Remove metal strap from behind factory seal (This is the metal strap that the previous 5 small torque screws were removed from) Position metal strap in same location on your new lid. (If you purchased your product unpainted, you must install the supplied seal to your finished lid) Reattach BAGGER AUDIO™ LIDS by installing the 5 small torque screws in the same location as on the factory lid. (We suggest that you have an assistant hold the lid in place while attaching your new lids) Replace factory nylon Hinge straps with new nylon straps supplied in kit. Use metal straps and machined screws to secure the nylon hinge straps. 
 Place a small bead of silicone on the inside rim of the speaker basket to create a watertight seal between the inside of the lid and the speaker. 
 Install speaker into the bottom of the lid (not through the top opening) with supplied stainless screws and washers (4 per lid). Be sure to center speaker in lid opening to ensure proper speaker grill placement. Install speaker with terminals facing toward the front of the lid. One 1/4″ hole must be drilled in each bag. Holes can be positioned at the ownerʼs discretion. Place rubber grommet in drilled hole before running wires

TOYOTA U SERIES VALVE BODY GASKETS

0

Filed Under (Toyota Manuals) by admin on 27-09-2011

download
75431 OE# 35431-21010 U140E/F 1998-02, U240E 1999-01, U241E 2000-04, U150E 2001, U151E/F 2003-04 VB COVER Kits K75900ET K75900KT, K75900E K75900F, K75900K, K75900KT K75900EX, K75900ETX COPYRIGHT©2006 PRECISION INTERNATIONAL.ALL RIGHTS RESERVED. REPRINTING IN WHOLE OR IN PART WITHOUT THE EXPRESS PERMISSION OF PRECISION INTERNATIONAL IS PROHIBITED 75075 OE# N/A U150E 2001, U151E/F 2003-04 AUXILIARY VB (Small) Kits K75900KT K75900EX, K75900ETX K75900K 75357 OE# 35477-52020 U340/341E/F 1999-03 VB COVER Kits K75900JTX K75900JT, K75900JX K75900J 75122 OE# N/A U441E 1999-05 MAIN VB (lower) Kits K75900L 75076 OE# N/A U150E 2001, U151E/F 2003-04 AUXILIARY VB (Large) Kits K75900KT K75900EX, K75900K K75900ETX 75358 OE# 35488-52010 U340/341E/F 1999-03 VB COVER Kits K75900JTX K75900JT, K75900JX K75900J 75123 OE# N/A U441E 1999-05 VB (upper) Kits K75900

HONDA ATV Carburetor Repair Kits Installation

0

Filed Under (Honda) by admin on 21-12-2011

download
ATV Carburetor Repair Kits Complete kits to rebuild one OEM carburetor. Each kit contains necessary gaskets/o-rings, needle valve or needle valve set, and jets. Made in Japan. Note: Check all parts before installation. Honda Model Year Order No AT C70 78-85 025-001 AT C90 70-71 025-003 ATC90K1/K2/K3 72-75 025-003 AT C90 76-78 025-003 TRX90 Fourtrax 90 93-98 025-084 ATC110 79-83 025-005 ATC110 84-85 025-061 ATC125M 84-85 025-062 TRX125 Fourtrax 85-86 025-050 TRX125 Fourtrax 87-88 025-063 ATC185 1980 025-009 ATC185S 81-83 025-009 AT C200 81-82 025-008 AT C200 1983 025-009 ATC200E Big Red 82-83 025-064 ATC200ES Big Red 1984 025-064 AT C200M 84-85 025-064 AT C200S 84-86 025-065 AT C200X 83-85 025-012 AT C200X 86-87 025-014 TRX200 Fourtrax 200 90-91 025-066 TRX200D Fourtrax 200 Type II 1991 025-066 TRX200D Fourtrax 200 Type II 92-93 025-067 TRX200D Fourtrax 200 Type II 94-97 025-068 TRX200SX Fourtrax 87-88 025-069 ATC250R 81-82 025-017 ATC250R 83-84 025-018 AT C250R 1985 025-019 ATC250ES Big Red 85-87 025-029 AT C250SX 1985 025-070 TRX250 Fourtrax 250 1985 025-071 TRX250 Fourtrax 250 86-87 025-072 TRX250EX Sportrax 250EX 01-04 025-085 TRX250R Fourtrax 250R 86-87 025-060 TRX250R Fourtrax 250R 1988 025-073 TRX250X 91-92 025-074 TRX300 Fourtrax 300 1988 025-075 TRX300 Fourtrax 300 91-92 025-076 TRX300 Fourtrax 300 93-95 025-078 Honda Model Year Order No TRX300EX Fourtrax 300EX 93-98 025-081 TRX300FW Fourtrax 300 4×4 1988 025-075 TRX300FW Fourtrax 300 4×4 91-92 025-076 TRX300FW Fourtrax 300 4×4 93-95 025-078 AT C350X 1985 025-035 TRX350 Fourtrax 4×4 86-87 025-079 TRX350FE Fourtrax Rancher 4×4 ES 00-03 025-082 TRX350FM Fourtrax Rancher 4×4 00-03 025-082 TRX350TE Fourtrax Rancher ES 00-03 025-082 TRX350TM Fourtrax Rancher 00-03 025-082 TRX350D Fourtrax Foreman 4×4 87-89 025-079 TRX400FW Fourtrax Foreman 95-00 025-080 TRX450ES Fourtrax Foreman ES 98-01 025-083 TRX450FE Fourtrax Foreman ES 02-03 025-083 TRX450FM Fourtrax Foreman S 02-03 025-083 TRX450S Fourtrax Foreman S 98-01 025-083 TRX500FAFourtrax Rubicon 01-04 025-086

Incoming search terms:

HARLEY DAVIDSON SOFTAIL CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Kit Contents See Figure 3 and Table 2 for complete kit contents. See Table 1 for the grab strap part number associated with each seat kit. Table 1. Kit Numbers and Grab Strap Usage Grab Strap Kit Number 51332-07 51310-07 51910-08 51936-08 51701-06 51308-07 51365-07 51367-07 51387-06A 51388-06 51389-06 51390-06 51391-06 51392-06 51398-07 51365-07 51410-08 51411-08 51412-08 51414-08 51415-08 51416-08 51407-08 The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) INSTALLATION NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. FXST, FXSTB and FXSTS Models 1. See Figure 3 and Table 2. Unscrew the captive thumbscrew fastening the back of the original equipment (OE) seat to the vehicle. 2. Pull the seat slightly to the rear to disengage the tang at the front of the seat from the motorcycle frame. 3. Lift the front of the seat while pulling the seat carefully forward to remove the seat from the vehicle. 4. Remove the OE grab strap and attaching hardware. Save the hardware for later use. 5. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap. 2007 and Later FLSTF Models 1. Remove original equipment (OE) seat and mounting hardware following the instructions in the Owner’s Manual. 2. Remove and discard the OE grab strap and attaching hardware. 3. See Figure 3. Install two flange nuts (9) from the kit onto the OE grab strap mounting studs (as shown in Figure 1, Item 1). 4. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap.

HARLEY DAVIDSON SOFTAIL DETACHABLE SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
Detachable Saddlebag Configurations Table 1 provides a short description of the detachable saddlebag configurations. Table 1. Softail Detachable Saddlebag Configurations Accessory Configuration (Long Description) Short Descrip- tion Kit 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Other Detachable Accessories FL Outer 88237-07 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) Without Other Detachable Accessories FL Inner 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Rigid-Mounted Accessories FL Rigid 2006-Later FX Models (Except FXSTD) With Other Detachable Accessories FX Outer 88238-07 2006-Later FX Models (Except FXSTD) Without Other Detachable Accessories FX Inner 2006-Later FX Models (Except FXSTD) With Rigid-Mounted Accessories FX Rigid 2007-Later FXSTC Models With Stock Passenger Upright FXSTC Stock NOTE Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Install Turn Signal Relocation Kit Refer to instructions included with Turn Signal Relocation Kit 69857-07. Install Docking Hardware Kit(s) Without Other Detachable Accessories: Refer to instructions included with Docking Hardware Kit 53932-03. With Other Detachable Accessories: Refer to instructions included with Docking Hardware Kits 53932-03 and 88256-07. Install Rear Docking Adapter NOTE This procedure only applies to models without detachable accessories. 1. See Figure 1. Insert rear docking adapter (1) into holes in saddlebag bracket and hold in place. 2. Install rear docking adapter using screw (2) and nut (3). Tighten snugly.

Incoming search terms:

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms: